Specifications Index

RDX COMMON SPECS & PROCEDURES INDEX

System		Specification/Procedure
Air Conditioning
Service		2013-15: AIR CONDITIONING 2016-18: AIR CONDITIONING
Torque		2013-15: HEATING, VENTILATION, AND AIR CONDITIONING 2016-18: HVAC SYSTEM
Axle Nut/Hub Nut
Front		328 N.m (242 ft. lbs.)
Rear Knuckle / Hub Bearing Bolts		2013-15: 181 N.m (133 ft. lbs.) 2016-18: 245 N.m (181 ft. lbs.)
Battery		BATTERY TEST
Brakes
Bleeding Sequence		CONVENTIONAL BRAKE SYSTEM BLEEDING (2013-18)
Disc Brakes		2013-15: BRAKES 2016-18: BRAKES
Torque		2013-15: BRAKES TORQUE SPECIFICATIONS (2013-15) 2016-18: BRAKES TORQUE SPECIFICATIONS (2016-18)
Charging
Generator brush length		2013-15: ENGINE ELECTRICAL 2016-18: ENGINE ELECTRICAL
Torque		2013-15: ENGINE ELECTRICAL 2016-18: ENGINE ELECTRICAL
Drive Belts
Belt Routing & Adjustment		2013-15: DRIVE BELT REMOVAL AND INSTALLATION 2016-18: DRIVE BELT REMOVAL AND INSTALLATION
Engine Cooling
General Service Specifications		2013-15: COOLING SYSTEM 2016-18: COOLING SYSTEM
Radiator Cap Pressure		93-123 kPa (0.95-1.25 kgf/cm2, 13.5-17.8 psi)
Thermostat R & I		2013-15: THERMOSTAT REMOVAL, INSTALLATION, AND TEST 2016-18: THERMOSTAT REMOVAL, INSTALLATION, AND TEST
Water Pump R & I		2013-15: WATER PASSAGE REMOVAL AND INSTALLATION 2016-18: WATER PUMP REMOVAL AND INSTALLATION
Engine Mechanical
Compression		930 kPa (9.48 kgf/cm² , 134.8 psi) Minimum 200 kPa (2.04 kgf/cm² , 29.0 psi) Maximum variation
Oil Pressure (176°F (80°C)		70 kPa (0.71 kgf/cm² , 10.1 psi) min. @ idle 490 kPa (5.00 kgf/cm² , 71.1 psi) min. @ 3000 RPM
Overhaul		2013-15: See applicable specifications tables in STANDARDS AND SERVICE LIMITS (2013-15) 2016-18: See applicable specifications tables in STANDARDS AND SERVICE LIMITS (KA/KC MODELS) (2016)
Torque		2013-15: ENGINE MECHANICAL 2016-18: ENGINE MECHANICAL
Fluid Specifications		See FLUIDS under MAINTENANCE tab.
Flywheel/Flex Plate Torque		74 N.m (55 ft. lbs.)
Fuel System
Pressure Specification		2013-15: 390-440 kPa (4.0-4.5 kgf/cm² , 57-64 psi) 2016-18: 400-450 kPa (4.08-4.59 kgf/cm² , 58-65.3 psi)
Fuel Pressure Test Procedure		2013-15: FUEL PRESSURE TEST 2016-18: FUEL PRESSURE TEST
Ignition
Firing Order & Cylinder Identification		FIRING ORDER & CYLINDER IDENTIFICATION
Spark Plug NGK: 7751
Gap		1.1 mm (.044 in.)
Torque		22 N.m (16 ft. lbs.)
Starting
Starter		2013-15: ENGINE ELECTRICAL 2016-18: ENGINE ELECTRICAL
Torque		2013-15: ENGINE ELECTRICAL 2016-18: ENGINE ELECTRICAL
Wheel Alignment
Adjustment Specifications		2013-15: SUSPENSION 2016-18: SUSPENSION
	Torque	2013-15: SUSPENSION 2016-18: SUSPENSION SYSTEM
Wheel & Tire
Wheel Lug Nut Torque		108 N.m (80 ft. lbs.)