Specifications Index

SPECIFICATIONS INDEX

System			Specification/Procedure
Air Conditioning
Service			REFRIGERANT R134A PHYSICAL DATA
Torque			N/A
Axle Nut/Hub Nut
Front			200 Nm +180°
Rear			200 Nm +180°
Battery			COLD CRANK AMPS TABLE
Brakes
Bleeding Sequence			HYDRAULIC SYSTEM, BLEEDING
Disc Brakes			FRONT BRAKES REAR BRAKES
Torque			FASTENER TIGHTENING SPECIFICATIONS Hydraulic Components FASTENER TIGHTENING SPECIFICATIONS Mechanical Components
Charging
Generator			N/A
Torque			FASTENER TIGHTENING SPECIFICATIONS
Drive Belts
Adjustment
2.0L			RIBBED BELT, REMOVING AND INSTALLING
3.0L			RIBBED BELT, REMOVING AND INSTALLING for Engine Code(s): CPNB RIBBED BELT, REMOVING AND INSTALLING for Engine Code(s): CTUC and CTUD
3.2L			RIBBED BELT, REMOVING AND INSTALLING
Belt Routing
		2.0L	See fig. 10 under Installing
	3.0L		See fig. 10 under Installing for Engine Code(s): CPNB See fig. 8 under Installing for Engine Code(s): CTUC and CTUD
	3.2L		See fig. 5 under Installing
Engine Cooling
General Service Specifications			Refer to the approrpiate FLUID CAPACITY TABLES information.
Radiator Cap Pressure
	2.0L		1.4 to 1.6 bar (20.30 to 23.20 psi)
	3.0L		1.4 to 1.6 bar (20.30 to 23.20 psi)
	3.2L		1.4 to 1.6 bar (20.30 to 23.20 psi)
Thermostat R & I
2.0L			COOLANT THERMOSTAT, REMOVING AND INSTALLING
	3.0L		Map Controlled Engine Cooling Thermostat -F265-, REMOVING AND INSTALLING for Engine Code(s): CPNB COOLANT THERMOSTAT, REMOVING AND INSTALLING for Engine Code(s): CTUC and CTUD
	3.2L		COOLANT PUMP/THERMOSTAT
Water Pump R & I
2.0L			COOLANT PUMP, REMOVING AND INSTALLING
	3.0L		COOLANT PUMP, REMOVING AND INSTALLING for Engine Code(s): CPNB COOLANT PUMP/THERMOSTAT for Engine Code(s): CTUC and CTUD
	3.2L		COOLANT PUMP, REMOVING AND INSTALLING
Engine Mechanical
2.0L
		Compression	COMPRESSION PRESSURE, CHECKING
Oil Pressure			Oil pressure when the vehicle is idling: 1.2 to 2.1 bar Oil pressure at 2000 RPM: 1.6 to 2.1 bar Oil pressure at 3, 700 RPM: 3.0 to 4.0 bar During the break-in phase, the oil pressure may be at 2000/min at 3.0 to 4.0 bar.
Overhaul			10 ENGINE ASSEMBLY
Torque			ENGINE, INSTALLING
3.0L
	Compression		COMPRESSION PRESSURE, CHECKING for Engine Code(s): CPNB COMPRESSION PRESSURE, CHECKING for Engine Code(s): CTUC and CTUD
	Oil Pressure		CTUC & CTUD Engines Oil pressure when the vehicle is idling: minimum 1.2 bar (17.4 psi) Oil pressure at 2, 000 RPM: minimum 1.5 bar (21.7 psi) CPNB Engine Oil pressure when the vehicle is idling: minimum 0.8 bar (11.6 psi) Oil pressure at 2, 000 RPM: minimum 1.5 bar (21.7 psi)
	Overhaul		10 ENGINE ASSEMBLY for CTUC & CTUD Engines 10 ENGINE ASSEMBLY for CPNB Engine
	Torque		Tightening Specifications for CTUC & CTUD Engines Tightening Specifications for CPNB Engine
3.2L
		Compression	COMPRESSION PRESSURE, CHECKING
Oil Pressure			Oil pressure at idle: at least 1.2 bar (17.40 psi) pressure. Oil pressure at 2000 RPM: at least 1.5 bar (21.75 psi) pressure.
Overhaul			10 ENGINE ASSEMBLY
Torque			Tightening Specifications
Fluid Specifications			See FLUIDS under MAINTENANCE tab.
Engine Oil Pan Drain Plug			30 Nm
Flywheel/Flex Plate Torque			60 Nm + 90°
Fuel System
Pressure Specification
2.0L			The fuel injection system is separated into a high-pressure section (maximum approximately 120 bar) and a low-pressure section (approximately 7 bar).
	3.0L		CTUC & CTUD Engines The fuel injection system is separated into a high-pressure section (maximum approximately 120 bar (1740 psi)) and a low-pressure section (approximately 7 bar (101.5 psi)). CPNB Engine N/A
3.2L			The injection system is separated into a high-pressure section (maximum approximately 120 bar (1740 psi)) and a low-pressure section (approximately 6 bar (87 psi))
Fuel Pressure Test Procedure
	2.0L		Fuel Pressure Sensor -G247-, CHECKING
	3.0L		FUEL PRESSURE AND RESIDUAL PRESSURE, CHECKING, VEHICLES WITH 3.0L TFSI ENGINE for CTUC & CTUD Engines FUEL PUMP, CHECKING FUEL PRESSURE for CPNB Engine
	3.2L		FUEL PRESSURE AND RESIDUAL PRESSURE BEFORE HIGH PRESSURE PUMP, CHECKING
Ignition
Firing Order & Cylinder Identification			FIRING ORDER & CYLINDER IDENTIFICATION
Ignition Wires (Resistance)			Coil-On-Plug
Ignition Wires (Routing)			Coil-On-Plug
Spark Plug
2.0L			TEST DATA AND SPARK PLUGS
	3.0L		TEST DATA AND SPARK PLUGS for CTUC & CTUD Engines CPNB N/A
3.2L			TEST DATA AND SPARK PLUGS
Starting
Starter			N/A
Torque			FASTENER TIGHTENING SPECIFICATIONS
Wheel Alignment
Adjustment Specifications			WHEEL ALIGNMENT SPECIFIED VALUES
Torque			FASTENER TIGHTENING SPECIFICATIONS
Wheel & Tire
Wheel Lug Nut Torque			140 Nm