Specifications Index
SPECIFICATIONS INDEX
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | Refrigerant R134a Physical Data | ||
| Torque | Fastener Tightening Specifications | ||
| Axle Nut/Hub Nut | |||
| Front | 200 Nm +180° turn | ||
| Rear | 200 Nm +180° | ||
| Battery | Battery | ||
| Brakes | |||
| Bleeding Sequence | BRAKE SYSTEM, BLEEDING Hydraulic Components | ||
| Disc Brakes | FRONT BRAKES REAR BRAKES |
||
| Torque | N/A | ||
| Charging | |||
| Generator | N/A | ||
| Torque | |||
| Drive Belts | |||
| Adjustment | |||
| 2.0L | RIBBED BELT, REMOVING AND INSTALLING | ||
| 3.0L | RIBBED BELT, REMOVING AND INSTALLING | ||
| Belt Routing | |||
| 2.0L | See fig. 7 under Installing | ||
| 3.0L | See fig. 10 under Installing | ||
| Engine Cooling | |||
| General Service Specifications | Refer to the approrpiate FLUID CAPACITY TABLES information. | ||
| Radiator Cap Pressure | |||
| 2.0L | Oil pressure at idle: 1.2 to 2.0 bar (17.4 to 29 psi) Oil pressure at 2000 RPM: 1.6 to 2.2 bar (23.2 to 32 psi) Oil pressure at 3700 RPM: 3 to 4 bar (43 to 58 psi) |
||
| 3.0L | 1.4 to 1.6 bar (20.30 to 23.20 psi) | ||
| Thermostat R & I | |||
| 2.0L | Coolant Thermostat, Removing And Installing | ||
| 3.0L | Coolant Thermostat, Removing And Installing | ||
| Water Pump R & I | |||
| 2.0L | Coolant Pump, Removing And Installing | ||
| 3.0L | Coolant Pump, Removing And Installing | ||
| Engine Mechanical | |||
| 2.0L | |||
| Compression | Compression Pressure, Checking | ||
| Oil Pressure | Oil pressure at idle: 1.2 to 2.0 bar (17.4 to 29 psi) Oil pressure at 2000 RPM: 1.6 to 2.2 bar (23.2 to 32 psi) Oil pressure at 3700 RPM: 3 to 4 bar (43 to 58 psi) During the Brake-in phase, the oil pressure may be at 2000 RPM at 3 to 4 bar (43 to 58 psi). |
||
| Overhaul | 10 ENGINE ASSEMBLY | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| 3.0L | |||
| Compression | Compression Pressure, Checking | ||
| Oil Pressure | Oil pressure when the vehicle is idling: minimum 1.2 bar (17.4 psi) Oil pressure at 2, 000 RPM: minimum 1.5 bar (21.7 psi). |
||
| Overhaul | 10 ENGINE ASSEMBLY | ||
| Torque | Tightening Specifications | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. | ||
| Engine Oil Pan Drain Plug | 30 Nm | ||
| Flywheel/Flex Plate Torque | 60 Nm + 90° | ||
| Fuel System | |||
| Pressure Specification | |||
| 2.0L | The injection system is separated into a high-pressure section (maximum approximately 120 bar (1740 psi) and a low-pressure section (approximately 6 bar (87 psi). | ||
| 3.0L | The fuel injection system is separated into a high-pressure section (maximum approximately 120 bar) and a low-pressure section (approximately 7 bar). | ||
| Fuel Pressure Test Procedure | |||
| 2.0L | Fuel Pressure Sensor -G247-, Checking | ||
| 3.0L | Fuel Pressure And Residual Pressure Before High Pressure Pump, Checking | ||
| Ignition | |||
| Firing Order & Cylinder Identification | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires (Resistance) | Coil-On-Plug | ||
| Ignition Wires (Routing) | Coil-On-Plug | ||
| Spark Plug | |||
| 2.0L | TEST DATA AND SPARK PLUGS | ||
| 3.0L | TEST DATA AND SPARK PLUGS | ||
| Starting | |||
| Starter | Cold Crank Amps Table | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Wheel Alignment | |||
| Adjustment Specifications | VEHICLE ALIGNMENT | ||
| Torque | Fastener Tightening Specifications
Front FASTENER TIGHTENING SPECIFICATIONS Rear |
||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 120 Nm | ||