Rearview Camera -R189-, CALIBRATING

-- Setup requirements, refer to Calibration Tool VAS6350, INSTALLING AND ALIGNING .

-- Connect the Vehicle Diagnostic Tester.

Calibration Tool - Wheel Center MountingsVAS6350/1 installing:

-- Check which hole circle the rims have.

-- Mount the Calibration Tool - Wheel Center MountingsVAS6350/1 appropriately.

-- To do so, attach three wheel bolt adapters in the bolt circle to each Calibration Tool - Wheel Center MountingsVAS6350/1.

-- Attach paddles to both Calibration Tool - Wheel Center MountingsVAS6350/1 and secure them with clamping screw.

-- Place the Wheel Center MountingsVAS6350/1 onto the wheel bolts on the rear wheels.

The Calibration Tool - Wheel Center MountingsVAS6350/1 are positioned by the "O rings" in the adapters and held in place.

Fig 1: Identifying Wheel Pick-Ups On Wheel Mounting Bolts At Rear Wheels

Courtesy of AUDI OF AMERICA, LLC

-- Adjust paddle with aid of clamping screws so that they move freely just above the floor. Make sure the paddles move easily.

-- Install and align the Calibration ToolVAS6350, refer to Calibration Tool VAS6350, INSTALLING AND ALIGNING .

Distance measurement:

-- Switch on the Calibration Tool - Spacing LaserVAS6350/2.

Fig 2: Identifying Laser Display

Courtesy of AUDI OF AMERICA, LLC

-- Hold the Calibration Tool - Spacing LaserVAS6350/2 -2- flush in the bracket on one side of the calibration board. The Calibration Tool - Spacing LaserVAS6350/2 -2- must sit securely in the bracket.

Fig 3: Ensuring Laser Beam From Distance Laser VAS 6350/2 Hits Lower, Enlarged Part Of Paddle

Courtesy of AUDI OF AMERICA, LLC

-- Press the measuring button briefly.

The laser turns on.

-- Make sure that the laser beam from Calibration Tool - Spacing LaserVAS6350/2 -2- hits on the lower, enlarged part of paddle -1-.

If this is not the case, correct the paddles accordingly using clamping screws on the Calibration Tool - Wheel Center MountingsVAS6350/1.

-- Use one hand to secure the Calibration Tool - Spacing LaserVAS6350/2 in the bracket on the Calibration UnitVAS6350A while the laser beam is visible on the paddle.

-- Press the measuring button briefly for the distance measurement.

Fig 4: Identifying Display Readout

Courtesy of AUDI OF AMERICA, LLC

-- Note the value read off.

-- Repeat measuring procedure in the same manner for the other rear wheel on the other side of the Calibration UnitVAS6350A.

The distance value must be the same on both sides.

If values are not identical:

-- Align the Calibration UnitVAS6350A long enough so that both sides are identical.

Pay attention when aligning the Calibration UnitVAS6350A, that the Calibration Tool - Linear LaserVAS6350/3 from the Calibration UnitVAS6350A strikes the center of the Audi rings and the indicator of the level remains centered. If necessary, make further corrections.

Dimension measurement -H- :

-- Measure the height of the Calibration UnitVAS6350A, dimension -H- (top edge platform - floor).

Fig 5: Identifying Height Of Calibration Platform, Dimension -H-

Courtesy of AUDI OF AMERICA, LLC

Enter the height and distance dimensions into the Vehicle Diagnostic Tester in "millimeters".

Performing calibration

Vehicle Diagnostic Tester is attached.

-- Select the Diagnostic  mode and start the diagnostics.

-- Select the tab test plan  .

-- Select select individual tests  and choose the following sequence.

• Body
• Electrical Equipment
• 01 - OBD-capable systems
• 6C - rearview camera system/J772
• 6C - rearview camera system control module, functions
• 6C - Calibration, (Repair Group 91)

From here the Vehicle Diagnostic Tester advances the calibration procedure forward.