Engine Control Module --, 2018 MY

DTC / Description	Monitor Strategy Description	Malfunction Criteria and Threshold Value	Secondary Parameters with Enable Conditions	Monitoring Time Length	MIL Illum.	Component Diagnostic Procedure
P000A "A" Camshaft Position Slow Response Bank 1	Variable Valve Timing (VVT) Intake Actuator Slow Response	Adjustment angle difference >= 1.0; < 10.0° CRK	Modeled oil temperature -40 - 160° C Engine speed 608 - 6, 016 RPM Set point change > 20.0° CRK Camshaft position not calibrated Dynamic diagnosis timer >= 0.95 - 4.0 s	0.0 (FTP75: 300.0) s Continuous	2 DCY	-- Check the Camshaft Adjustment Valve 1 -N205-. Refer to Camshaft Adjustment Valve 1 - N205-, CHECKING .-- Check the Camshaft Position Sensor -G40-. Refer to Camshaft Position Sensor - G40-, CHECKING .-- Check the Fuel Pressure Regulator Valve -N276-. Refer to Fuel Metering Valve - N290-, CHECKING .-- Check the Engine Speed Sensor -G28-. Refer to Engine Speed Sensor - G28-, CHECKING
P000B "B" Camshaft Position Slow Response Bank 1	Variable Valve Timing (VVT) Exhaust Actuator Slow Response	Adjustment angle difference>= 1.0; < 3.50° CRK	Modeled oil temperature -40 - 160° C Engine speed 608 - 6, 016 RPM Set point change > 6.0° CRK Camshaft position not calibrated Dynamic diagnosis timer >= 0.95 - 4.0 s	0.0 (FTP75: 700.0) s Continuous	2 DCY	-- Check the Exhaust Camshaft Adjustment Valve 1 -N318-. Refer to Exhaust Camshaft Adjustment Valve 1 - N318-, CHECKING .-- Check the Camshaft Position Sensor -G40-. Refer to Camshaft Position Sensor - G40-, CHECKING .-- Check the Fuel Pressure Regulator Valve -N276-. Refer to Fuel Metering Valve - N290-, CHECKING .-- Check the Engine Speed Sensor -G28-. Refer to Engine Speed Sensor - G28-, CHECKING .
P0010 "A" Camshaft Position Actuator Control Circuit/Open Bank 1	Variable Valve Timing (VVT) Intake Actuator Open Circuit	Output voltage lower range 1.92 - 2.21 V Output voltage upper range 2.85 - 3.25 V	Actuator commanded off	2.0 s Continuous	2 DCY	-- Check the Engine Speed Sensor -G28-. Refer to Engine Speed Sensor - G28-, CHECKING .-- Check the Camshaft Position Sensor -G40-. Refer to Camshaft Position Sensor - G40-, CHECKING .-- Check the Camshaft Adjustment Valve 1 -N205-. Refer to Camshaft Adjustment Valve 1 - N205-, CHECKING .-- Check the Fuel Pressure Regulator Valve -N276-. Refer to Fuel Metering Valve - N290-, CHECKING .
P0011 "A" Camshaft Position - Timing Over-Advanced or System Performance Bank 1	Variable Valve Timing (VVT) Intake Actuator Target Error	Camshaft position deviation > 10.0° CRK	Modeled oil temperature -40 - 160° C Engine speed 608 - 6, 016 RPM Camshaft position not calibrated Camshaft position adjustment active Catalyst heating not active Camshaft position deviation integrator (actual vs. set point position) >= 9.0 - 12.0° CRK	0.0 (FTP75: 250.0) s Continuous	2 DCY	-- Check the Engine Speed Sensor -G28-. Refer to Engine Speed Sensor - G28-, CHECKING -- Check the Camshaft Position Sensor -G40-. Refer to Camshaft Position Sensor - G40-, CHECKING .-- Check the Camshaft Adjustment Valve 1 -N205-. Refer to Camshaft Adjustment Valve 1 - N205-, CHECKING .-- Check the Fuel Pressure Regulator Valve -N276-. Refer to Fuel Metering Valve - N290-, CHECKING .
P0013 "B" Camshaft Position Actuator Control Circuit/Open Bank 1	Variable Valve Timing (VVT) Exhaust Actuator Open Circuit	Output voltage, lower range1.92 - 2.21 V Output voltage, upper range2.85 - 3.25 V	Actuator commanded off	2.0 s Continuous	2 DCY	-- Check the Exhaust Camshaft Adjustment Valve 1 -N318-. Refer to Exhaust Camshaft Adjustment Valve 1 - N318-, CHECKING .-- Check the Engine Speed Sensor -G28-. Refer to Engine Speed Sensor - G28-, CHECKING .-- Check the Camshaft Position Sensor -G40-. Refer to Camshaft Position Sensor - G40-, CHECKING .-- Check the Camshaft Adjustment Valve 1 -N205-. Refer to Camshaft Adjustment Valve 1 - N205-, CHECKING .-- Check the Fuel Pressure Regulator Valve -N276-. Refer to Fuel Metering Valve - N290-, CHECKING .
P0014 "B" Camshaft Position - Timing Over-Advanced or System Performance Bank 1	Variable Valve Timing (VVT) Exhaust Actuator Target Error	Difference between target and actual position > 10.0° CRK	Modeled oil temperature -40 - 160° C Engine speed 608 - 6, 016 RPM Camshaft position not calibrated Camshaft position adjustment active Catalyst heating not active Camshaft position deviation integrator (actual vs. set point position) >= 9.0 - 12.0° CRK	0.0 (FTP75: 450.0) s Continuous	2 DCY	-- Check the Exhaust Camshaft Adjustment Valve 1 -N318-. Refer to Exhaust Camshaft Adjustment Valve 1 - N318-, CHECKING .-- Check the Engine Speed Sensor -G28-. Refer to Engine Speed Sensor - G28-, CHECKING .-- Check the Camshaft Position Sensor -G40-. Refer to Camshaft Position Sensor - G40-, CHECKING .-- Check the Camshaft Adjustment Valve 1 -N205-. Refer to Camshaft Adjustment Valve 1 - N205-, CHECKING .-- Check the Fuel Pressure Regulator Valve -N276-. Refer to Fuel Metering Valve - N290-, CHECKING .
P0016 Crankshaft Position - Camshaft Position Correlation Bank 1 Sensor A	Camshaft Position / Crankshaft Position Adaptation Value Monitoring	Diff. actual camshaft adaptation per cylinder vs. previous >= 12.0° CRK	General: Camshaft phasing commanded Engine speed < 8, 160 RPM Diff. actual intake camshaft position vs. previous camshaft position @ reference signal edge < 2.0° CRK Case 1: ignition off Engine speed > 380 RPM Engine stalling >= 1.0 s CKP stalling not detected Case 2: ignition on Synchronization test incorrect Or Engine running And Depending on engine: Engine stalling >= 5.0 s CKP stalling not detected Case 3: backwards rotation Backwards rotation not detected CKP stalling not detected Case 4: stop/start-cycle Engine speed >= 400 RPM Engine stopped	0.1 s Continuous	2 DCY	-- Check the Engine Speed Sensor -G28-. Refer to Engine Speed Sensor - G28-, CHECKING .-- Check the Camshaft Position Sensor -G40-. Refer to Camshaft Position Sensor - G40-, CHECKING .-- Check the Camshaft Adjustment Valve 1 -N205-. Refer to Camshaft Adjustment Valve 1 - N205-, CHECKING .
	Camshaft Position / Crankshaft Position (CMP / CKP) Intake Sensor Adaptation Value Monitoring	Adapted value for each edge of the target wheel < -14.0° CRK Or Adapted value for each edge of > 14.0° CRK	Camshaft position adjustment active (Exhaust side) Engine speed 288 - 4, 000 RPM Modeled oil temperature >= -15° C Modeled oil temperature <= 160° C Diff. actual exhaust camshaft position vs. previous camshaft position @ reference signal edge < 2.0° CRK And Case 1: Ignition off Engine speed > 380 RPM Engine stalling >= 1.0 s Or Case 2: Engine speed >= 380 RPM Or Engine running And Engine stalling>= 5.0 s CKP stalling not detected Or Case 3: Backwards rotation not detected CKP stalling not detected Or Case 4: Engine speed>= 400 RPM Engine stopped	720.0° CRK Multiple	2 DCY
P0017 Crankshaft Position - Camshaft Position Correlation Bank 1 Sensor B	Camshaft Position / Crankshaft Position (CMP / CKP) Exhaust Sensor Adaptation Value Monitoring	Adapted value for each edge of the target wheel < -14.0° CRK Or Adapted value for each edge of > 14.0° CRK	Camshaft position adjustment active (Exhaust side) Engine speed 288 - 4, 000 RPM Modeled oil temperature >= -15° C Modeled oil temperature <= 160° C Diff. actual exhaust camshaft position vs. previous camshaft position @ reference signal edge < 2.0° CRK And Case 1: Ignition off Engine speed > 380 RPM Engine stalling >= 1.0 s CKP stalling not detected Or Case 2: Engine speed >= 380 RPM Or Engine running And Engine stalling>= 5.0 s CKP stalling not detected Or Case 3: Backwards rotation not detected CKP stalling not detected Or Case 4: Engine speed>= 400 RPM Engine stopped	720.0° CRK Multiple	2 DCY	-- Check the Exhaust Camshaft Adjustment Valve 1 -N318-. Refer to Exhaust Camshaft Adjustment Valve 1 - N318-, CHECKING .-- Check the Engine Speed Sensor -G28-. Refer to Engine Speed Sensor - G28-, CHECKING .
P0030 HO2S Heater Control Circuit Bank 1 Sensor 1	Oxygen Sensors (O2S) Heater Front Open Circuit	O2S front heater voltage lower range 1.92 - 2.21 V O2S front heater voltage upper range 2.85 - 3.25 V		2.5 s Continuous	2 DCY	-- Check the Oxygen Sensor 1 Before Catalytic Converter -GX10-. Refer to Oxygen Sensor 1 Before Catalytic Converter - GX10-, CHECKING .
P0031 HO2S Heater Control Circuit Low Bank 1 Sensor 1	Oxygen Sensors (O2S) Heater Front Short To Ground	O2S front heater voltage < 1.92 - 2.21 V		2.5 s Continuous	2 DCY	-- Check the Oxygen Sensor 1 Before Catalytic Converter -GX10-. Refer to Oxygen Sensor 1 Before Catalytic Converter - GX10-, CHECKING .
P0032 HO2S Heater Control Circuit High Bank 1 Sensor 1	Oxygen Sensors (O2S) Heater Front Short To Battery Plus	O2S front heater driver temperature > 160.0 - 200.0° C Or O2S front heater driver output current > 8.0 - 12.0 A	Modeled EGT @ O2S front >= -273° C Actuator commanded on	2.5 s Continuous	2 DCY	-- Check the Oxygen Sensor 1 Before Catalytic Converter -GX10-. Refer to Oxygen Sensor 1 Before Catalytic Converter - GX10-, CHECKING .
P0033 Turbocharger/Supercharger Bypass Valve "A" Control Circuit	Turbocharger (TC) Compressor Actuator Open Circuit	Voltage, lower range1.92 - 2.21 V Voltage, upper range2.85 - 3.25 V	Actuatorcommanded off	1.0 s Continuous	2 DCY	-- Check the Turbocharger Recirculation Valve -N249-. Refer to Turbocharger Recirculation Valve - N249-, CHECKING .-- Check the Charge Air Pressure Actuator -V465-. Refer to Charge Air Pressure Actuator - V465- / Charge Air Pressure Actuator Position Sensor - G581-, CHECKING .
	Turbocharger (TC) Compressor Actuator Short To Battery Plus	Current> 4.0 - 7.0 A Or Temperature > 160 - 200° C	Actuatorcommanded on	1.0 s Continuous	2 DCY
P0034 Turbocharger/Supercharger Bypass Valve "A" Control Circuit Low	Turbocharger (TC) Compressor Actuator Short To Ground	Voltage< 1.92 - 2.21 V	Actuatorcommanded off	1.0 s Continuous	2 DCY	-- Check the Turbocharger Recirculation Valve -N249-. Refer to Turbocharger Recirculation Valve - N249-, CHECKING .-- Check the Charge Air Pressure Actuator -V465-. Refer to Charge Air Pressure Actuator - V465- / Charge Air Pressure Actuator Position Sensor - G581-, CHECKING .
P0036 HO2S Heater Control Circuit Bank 1 Sensor 2	Oxygen Sensors (O2S) Heater Rear Open Circuit	O2S rear heater voltage lower range 1.92 - 2.21 V O2S rear heater voltage upper range 2.85 - 3.25 V	Engine not in start process	2.5 s Continuous	2 DCY	-- Check the Oxygen Sensor 1 After Catalytic Converter -GX7-. Refer to Oxygen Sensor 1 After Catalytic Converter - GX7-, CHECKING .
P0037 HO2S Heater Control Circuit Low Bank 1 Sensor 2	Oxygen Sensors (O2S) Heater Rear Short To Ground	O2S rear heater voltage < 1.92 - 2.21 V	Engine not in start process	2.5 s Continuous	2 DCY	-- Check the Oxygen Sensor 1 After Catalytic Converter -GX7-. Refer to Oxygen Sensor 1 After Catalytic Converter - GX7-, CHECKING .
P0038 HO2S Heater Control Circuit High Bank 1 Sensor 2	Oxygen Sensors (O2S) Heater Rear Short To Battery Plus	O2S rear heater driver temperature > 160.0 - 200.0° C Or O2S rear heater driver output current > 8.0 - 12.0 A	Modeled EGT @ O2S rear >= -273° C Actuator commanded on Engine not in start process	2.5 s Continuous	2 DCY	-- Check the Oxygen Sensor 1 After Catalytic Converter -GX7-. Refer to Oxygen Sensor 1 After Catalytic Converter - GX7-, CHECKING .
P0045 Turbocharger/Supercharger Boost Control "A" Circuit/Open	Turbocharger (TC) Boost Pressure Control Open Circuit	Bypass valve driver load resistance > 200.0 kΩ	Deviation between actual and filtered boost pressure actuator position <= 5.0% Boost pressure control not active Time delay > 1.0 s	0.4 s Continuous	2 DCY	-- Check the Turbocharger Recirculation Valve -N249-. Refer to Turbocharger Recirculation Valve - N249-, CHECKING .-- Check the Charge Air Pressure Actuator -V465-. Refer to Charge Air Pressure Actuator - V465- / Charge Air Pressure Actuator Position Sensor - G581-, CHECKING .
P0068 MAP/MAF - Throttle Position Correlation	Intake Air (IA) System Rationality Check	Throttle opening area correction included controller and adaptation < -60.0% Lambda controller included correction and adaptation -30.0 - 30.0% Lambda controller active	Intake manifold modeled adaptation active (By throttle opening area) Throttle position 0.0 - 100.003° TPS Engine speed 576 - 3, 008 RPM Pressure quotient @ throttle 0.22 - 0.60 [-] Fast throttle adaptation finished MAP gradient -200.0 - 200.0 kPa/s Fuel cut off not active Time after engine start > 5.0 s Turbocharger boost pressure 135.0 kPa BARO 73.0 - 107.50 kPa	5.0 s Continuous	2 DCY	-- Check the Intake system for vacuum leaks, make sure oil dipstick is pushed properly into place.-- Check the Throttle Valve Control Module -GX3-. Refer to Throttle Valve Control Module - GX3-, CHECKING .-- Check the Intake Manifold Sensor -GX9-. Refer to Intake Manifold Sensor - GX9-, CHECKING .-- Check the EVAP Canister Purge Regulator Valve 1 -N80-. Refer to EVAP Canister Purge Regulator Valve 1 - N80-, CHECKING .
P0068 MAP/MAF - Throttle Position Correlation	Manifold Absolute Pressure (MAP) Sensor Large Leakage Detection	Difference MAP set point vs. actual MAP < -15.0 - -10.0 kPa	Fast throttle adaptation finished MAP gradient -200.0 - 200.0 kPa/s Vehicle speed <= 1 mph Time after engine start > 5.0 s Engine speed, lower range > 576 RPM Engine speed, upper range < 3, 000 RPM IAT @ manifold > -48° C ECT @ cylinder head > -48° C Pressure quotient @ throttle 0.10 - 0.60 [-] Load dynamic conditions: Dynamic engine speed < 8, 160 RPM Dynamic air mass < 15.01 mg/stk	5.0 s Continuous	2 DCY
P0070 Ambient Air Temperature Sensor Circuit "A"	COM: Ambient Air Temperature (AAT) Sensor Short To Battery / Open Circuit	AAT sensor voltage > 4.50 V		2.0 s Continuous	2 DCY	-- Check the Outside Air Temperature Sensor -G17-. Refer to Outside Air Temperature Sensor - G17-, CHECKING .
P0071 Ambient Air Temperature Sensor Circuit "A" Range/Performance	Ambient Air Temperature (AAT) Sensor Cross Check	High side: reference measuring Diff. AAT @ cold start vs. IAT @ manifold @ cold start > 25.0 K Diff. AAT @ cold start vs. ECT @ cylinder head @ cold start n.a. K Diff. AAT @ cold start vs. ECT @ radiator outlet @ cold start > 25.0 K Min. amount of faulty reference measurements to detect defective sensor 2.0 [-] Or Low side: reference measuring Diff. IAT @ manifold @ cold start vs. AAT @ cold start > 25.0 K Diff. ECT @ cylinder head @ cold start vs. AAT @ cold start n.a. K Diff. ECT @ radiator outlet @ cold start vs. AAT @ cold start > 25.0 K Min. amount of faulty reference measurements to detect 2.0 [-]	Engine off time >= 360.0 min Engine off time plausible Time after engine start < 1, 400.0 s Depending on temperature slope @ cold start: Diff. actual IAT @ manifold vs. IAT @ manifold @ start of DCY < 256.0 K Diff. actual ECT @ cylinder head vs. ECT @ cylinder head @ start of DCY n.a. K Diff. actual ECT @ radiator outlet vs. ECT @ radiator outlet @ start of DCY < 256.0 K Diff. actual AAT vs. AAT @ start of DCY < 256.0 K For time >= 1.0 s Depending on mean value condition Mean value of all temperature sensors @ cold start>= -256° C Number of valid sensors >= 2.0 [-] Depending on block heater / solar radiation detection Time after engine start >= 0.5 s Vehicle speed >= 22 mph For time>= 20.0 s Diff. actual IAT @ manifold vs. min. IAT @ manifold < 5.0 K Diff. actual ECT @ cylinder head vs. min. ECT @ cylinder head n.a. K Diff. actual AAT vs. min. AAT < 4.0 K Diff. actual ECT @ radiator outlet vs. min. ECT @ radiator outlet < 1.1 K	0.1 s Once / DCY	2 DCY	-- Check the Outside Air Temperature Sensor -G17-. Refer to Outside Air Temperature Sensor - G17-, CHECKING .
P0072 Ambient Air Temperature Sensor Circuit "A" Low	COM: Ambient Air Temperature (AAT) Sensor Short To Ground	AAT sensor voltage < 0.10 V		2.0 s Continuous	2 DCY	-- Check the Outside Air Temperature Sensor -G17-. Refer to Outside Air Temperature Sensor - G17-, CHECKING .
P0087 Fuel Rail/System Pressure - Too Low Bank 1	Fuel Rail Pressure (FRP) Out Of Range Low	Deviation between reference fuel pressure set point and current fuel pressure > 2, 999.80 kPa Case 1: Deviation lambda of controller included adaptation -50.0 - 50.0% High pressure controller output > 45.0 mg Fuel pressure > 3, 500.31 kPa Case 2: Fuel pump at max limit Mass fuel flow set point < 1, 389.0 mg/stk Fuel pressure < 34, 777.60 kPa	General: Engine speed608 - 6, 816RPM Fuel mass set point5.0 - 1, 389.0 0 mg/stk Time after engine start > 10.0 s Engine warm-up not calibrated Catalyst heating not calibrated Full loadnot calibrated Catalyst purgenot calibrated Lambda control not calibrated Evap purge functionality diagnosisnot calibrated Fuel pressure set point gradient<= 34, 777.60 kPa And Depending on low dynamic conditions: Fuel mass set point lower range > 5.0 mg/stk For time >= 10.0 s Fuel mass set point upper range< 187.17 - 229.23 mg/stk Fuel mass set point gradient-1, 389.0 - 1, 389.0 mg/stk For time>= 5.0 s And Depending on canister purge: Canister load not calibrated [-] Or Evap purge valve not calibrated	5.0 s Continuous	2 DCY	-- Check the fuel pressure and delivery quantity. Refer to fuel system mechanical testing in PRELIMINARY CHECK and/or to appropriate repair information.-- Check the Fuel Pressure Sensor -G247-. Refer to Fuel Pressure Sensor - G247-, CHECKING .-- Check the Fuel Pressure Regulator Valve -N276-. Refer to Fuel Metering Valve - N290-, CHECKING .-- Check the Fuel Delivery Unit -GX1- / Fuel Pump Control Module -J538-. Refer to Fuel Delivery Unit -GX1- / Fuel Pump Control Module -J538-, CHECKING .
P0087 Fuel Rail/System Pressure - Too Low Bank 1	Fuel Rail Pressure (FRP) Rationality Check Low	Deviation lambda of controller included adaptation -50.0 - 50.0% And High pressure controller output > 45.0 mg And Deviation between fuel pressure set point and current fuel pressure > 2, 999.80 kPa And Fuel pressure >= 3, 500.31 kPa		5.0 s Continuous	2 DCY
P0088 Fuel Rail/System Pressure - Too High Bank 1	Fuel Rail Pressure (FRP) Out Of Range High	Deviation between fuel pressure set point and current fuel pressure < -2, 999.90 kPa Deviation lambda of controller included adaptation -50.0 - 50.0% Case 1: High pressure controller output < -45.0 mg Case 2: Flow control valve open Mass fuel flow set point > 15.01 mg/stk	General: Engine speed 608 - 6, 816 RPM Fuel mass set point 5.0 - 1, 389.0 mg/stk Time after engine start > 10.0 s Engine warm-up not calibrated Catalyst heating not calibrated Full load not calibrated Catalyst purge not calibrated Lambda control not calibrated Evap purge functionality diagnosis not calibrated Fuel pressure set point gradient <= 34, 777.60 kPa And Depending on low dynamic conditions: Fuel mass set point lower range > 5.0 mg/stk For time >= 10.0 s Fuel mass set point upper range < 187.17 - 229.23 mg/stk Fuel mass set point gradient -1, 389.0 - 1, 389.0 mg/stk For time >= 5.0 s And Depending on canister purge: Canister load not calibrated [-] Or Evap purge valve not calibrated	5.0 s Continuous	2 DCY	-- Check the fuel pressure and delivery quantity. Refer to fuel system mechanical testing in PRELIMINARY CHECK and/or to appropriate repair information.-- Check the Fuel Pressure Sensor -G247-. Refer to Fuel Pressure Sensor - G247-, CHECKING .-- Check the Fuel Pressure Regulator Valve -N276-. Refer to Fuel Metering Valve - N290-, CHECKING .
P0090 Fuel Pressure Regulator 1 Control Circuit/Open	Fuel Volume Regulator Control Open Circuit	Voltage high side< 1.87 - 2.26 V Voltage low side> 2.78 - 3.33V	Engine speed0 RPM Or Fuel cut offactive Actuator commanded off	0.8 s Continuous	2 DCY	-- Check the Fuel Delivery Unit -GX1- / Fuel Pump Control Module -J538-. Refer to Fuel Delivery Unit -GX1- / Fuel Pump Control Module -J538-, CHECKING .-- Check the Fuel Pressure Regulator Valve -N276-. Refer to Fuel Metering Valve - N290-, CHECKING .
P0090 Fuel Pressure Regulator 1 Control Circuit/Open	Fuel Volume Regulator Control Open Circuit	Low and high side off: Voltage low side > 2.78 - 3.33V Voltage high side< 1.87 - 2.26V Low and high side on: Current low side < 12.2 - 15.0 A Current high side< 13.5 - 16.5 A	Engine speed> 600 RPM And Fuel cut offnot active Actuator commanded on	0.8 s Continuous	2 DCY
P0091 Fuel Pressure Regulator 1 Control Circuit Low	Fuel Volume Regulator Control Short To Ground (High Side)	Current high side> 13.5 - 17.0 A	Ignition on Or Ignition off (during ECM keep alive-time) And Actuatorcommanded on	0.8 s Continuous	2 DCY	-- Check the Fuel Delivery Unit -GX1- / Fuel Pump Control Module -J538-. Refer to Fuel Delivery Unit -GX1- / Fuel Pump Control Module -J538-, CHECKING .-- Check the Fuel Pressure Regulator Valve -N276-. Refer to Fuel Metering Valve - N290-, CHECKING .
P0091 Fuel Pressure Regulator 1 Control Circuit Low	Fuel Volume Regulator Control Short To Ground (Low Side)	Voltage low side < 1.87 - 2.26V (hardware values)	Ignition on Or Ignition off (during ECM keep alive-time) And Actuatorcommanded off	0.8 s Continuous	2 DCY
P0092 Fuel Pressure Regulator 1 Control Circuit High	Fuel Volume Regulator Control Short To Battery Plus (Low Side)	Current low side > 13.5 - 17.0 A	Ignition on Or Ignition off (during ECM keep alive-time) And Actuator commanded on	0.8 s Continuous	2 DCY	-- Check the Fuel Delivery Unit -GX1- / Fuel Pump Control Module -J538-. Refer to Fuel Delivery Unit -GX1- / Fuel Pump Control Module -J538-, CHECKING .-- Check the Fuel Metering Valve -N290-. Refer to Fuel Metering Valve - N290-, CHECKING .
P0092 Fuel Pressure Regulator 1 Control Circuit High	Fuel Volume Regulator Control Short To Battery Plus (High Side)	Voltage high side < 2.78 - 3.33 V	Ignition on Or Ignition off (during ECM keep alive-time) And Actuator commanded off	0.8 s Continuous	2 DCY
P00AF Turbocharger/Supercharger Boost Control "A" Module Performance	Turbocharger (TC) Boost Pressure Control Rationality Check	Diff. set point boost pressure actuator vs. actual position > 12.0 - 100.0%	Time after engine start >= 4.0 s ECT @ cylinder head > -40° C AAT > -40° C	0.5 s Continuous	2 DCY	-- Check the Charge Air Pressure Actuator -V465-. Refer to Charge Air Pressure Actuator - V465- / Charge Air Pressure Actuator Position Sensor - G581-, CHECKING .
	Turbocharger (TC) Boost Pressure Control Rationality Check Low	Boost pressure actuator position controller output < -98.0%	Time after engine start > 4.0 s ECT @ cylinder head > -40° C AAT > -40° C Diff. set point boost pressure actuator vs. actual position boost pressure actuator <= 12.0 - 100.0%
	Turbocharger (TC) Boost Pressure Control Rationality Check High	Boost pressure actuator position controller output > 98.0%	Time after engine start >= 4.0 s ECT @ cylinder head > -40° C AAT > -40° C Diff. set point boost pressure actuator vs. actual position boost pressure actuator <= 12.0 - 100.0%
P00B7 Engine Coolant Flow Low/Performance	Engine Cooling System: Bypass Valve Functional Check	Diff. previous and actual position of RVC < 4.0° [-] And Delay time 0.5 s	ECT @ cylinder head > 11° C RVC position 240.02 - 270.0° [-] Diff. previous actual and target position of RVC > 5.0° [-] And RVC adaptation finished Or RVC adaptation not active	14.0 s Continuous	2 DCY	-- Check the engine coolant system for leaks or damage. Repair as necessary. Refer to appropriate repair information.-- Check the Engine Temperature Control Actuator -N493-. Refer to Engine Temperature Control Actuator - N493-, CHECKING ..
			ECT @ cylinder head > 11° C RVC position 135.02 - 240.0° [-] Diff. previous actual and target position of RVC > 5.0° [-] And RVC adaptation finished Or RVC adaptation not active
			ECT @ cylinder head > 11° C RVC position 100.02 - 135.0° [-] Diff. previous actual and target position of RVC > 5.0° [-] And RVC adaptation finished Or RVC adaptation not active
			ECT @ cylinder head > 11° C RVC position 0.0 - 100.0° [-] Diff. previous actual and target position of RVC > 5.0° [-] And RVC adaptation finished Or RVC adaptation not active
P0106 Manifold Absolute Pressure/Barometric Pressure Sensor Circuit Range/Performance	Intake Air (IA) System Rationality Check	Throttle opening area correction included controller and adaptation < 45.0% Lambda controller included correction and adaptation > 30.0%	Intake manifold modeled adaptation active (By throttle opening area) Throttle position 0.0 - 100.003° TPS Engine speed 576 - 3, 008 RPM Pressure quotient @ throttle 0.22 - 0.60 [-] Fast throttle adaptation finished MAP gradient -200.0 - 200.0 kPa/s Fuel cut off not active Time after engine start > 5.0 s Turbocharger boost pressure < 135.0 kPa BARO 73.0 - 107.50 kPa	5.0 s Continuous	2 DCY	-- Check the Throttle Valve Control Module -GX3-. Refer to Throttle Valve Control Module - GX3-, CHECKING .-- Check the Charge Air Pressure Sensor -G31-. Refer to Charge Air Pressure Sensor - G31-, CHECKING .-- Check the Intake Manifold Sensor -GX9-. Refer to Intake Manifold Sensor - GX9-, CHECKING .
	Intake Air (IA) System Rationality Check	Throttle opening area correction included controller and adaptation > 45.0% Lambda controller included < -30.0%		5.0 s Continuous
	Manifold Absolute Pressure (MAP) Sensor Engine Standing: Cross Check	Case 1: charged engine Diff. BARO vs MAP > 8.50 kPa Diff. turbocharger boost pressure vs. MAP> 8.50 kPa Diff. BARO vs. turbocharger boost pressure <= 8.50 kPa Case 2: non charged engine Diff. BARO mean value vs. MAP mean value not calibrated kPa Diff. deviation BARO mean value to mean value (MAP mean value, BARO mean value, BARO @ ECM keep alive time and MAP @ ECM keep alive time) not calibrated kPa Diff. deviation MAP mean value to mean value (MAP mean value, BARO mean value, BARO @ ECM keep alive time and MAP @ ECM keep alive time) not calibrated kPa Diff. BARO mean value @ ECM keep alive vs. MAP mean value @ ECM keep alive time not calibrated kPa Diff. BARO mean value vs. MAP mean value not calibrated kPa	Case A: engine stop during DCY Engine stopped Vehicle speed< 1 mph Engine @ driving cycle not calibrated For time >= 10.0 s Case B: engine stop @ start of DCY Engine stopped Vehicle speed< 1 mph Engine @ driving cycle not calibrated	3.0 s Continuous
	Manifold Absolute Pressure (MAP) Sensor ECM Keep Alive-Time: Cross Check	Case 1: charged engine Diff. BARO vs MAP > 8.50 kPa Diff. BARO vs. turbocharger boost pressure <= 8.50 kPa Diff. turbocharger boost pressure vs. MAP > 8.50 kPa Case 2: non charged engine Diff. BARO mean value @ ECM not calibrated kPa	Engine stopped Vehicle speed< 1 mph ECM keep alive time 10.0 - 6, 553.5 s Time after engine stop >= 5.0 s BARO sensor voltage 0.20 - 4.80 V MAP sensor voltage 0.20 - 4.80 V Boost pressure sensor voltage 0.20 - 4.80 V
	Manifold Absolute Pressure (MAP) Sensor Full Load: Cross Check	Diff. BARO vs. MAP > 543.40 kPa	Engine speed 2, 000 - 8, 160 RPM Throttle position >= 27.353 - 78.004° TPS For time >= 2.0 s
P0107 Manifold Absolute Pressure/Barometric Pressure Sensor Circuit Low	Manifold Absolute Pressure (MAP) Sensor Circuit Low	Intake manifold pressure sensor voltage < 0.20 V		0.5 s Continuous	2 DCY	-- Check the Throttle Valve Control Module -GX3-. Refer to Throttle Valve Control Module - GX3-, CHECKING .-- Check the Intake Manifold Sensor -GX9-. Refer to Intake Manifold Sensor - GX9-, CHECKING .
P0108 Manifold Absolute Pressure/Barometric Pressure Sensor Circuit High	Manifold Absolute Pressure (MAP) Sensor Circuit High	Intake manifold pressure sensor voltage > 4.80 V		0.5 s Continuous	2 DCY	-- Check the Intake Manifold Sensor -GX9-. Refer to Intake Manifold Sensor - GX9-, CHECKING .
P0111 Intake Air Temperature Sensor 1 Circuit Range/Performance Bank 1	Intake Air Temperature (IAT) Sensor @ Manifold Cross Check	High side: reference measuring Diff. IAT @ manifold @ cold start vs. AAT @ cold start > 25.0 K Diff. IAT @ manifold @ cold start vs. ECT @ cylinder head @ cold start n.a. K Diff. IAT @ manifold @ cold start vs. ECT @ radiator outlet @ cold start > 25.0 K Min. amount of faulty reference measurements to detect defective sensor 2.0 [-] Or Low side: reference measuring Diff. AAT @ cold start vs. IAT @ manifold @ cold start > 25.0 K Diff. ECT @ cylinder head @ cold start vs. IAT @ manifold @ cold start > 25.0 K Diff. ECT @ radiator outlet @ cold start vs. IAT @ manifold @ cold start > 25.0 K Min. amount of faulty reference measurements to detect 2.0 [-]	Engine off time >= 360.0 min Engine off time plausible Time after engine start <= 1, 400.0 s Depending on temperature slope @ cold start: Diff. actual IAT @ manifold vs. IAT @ manifold @ start of DCY < 256.0 K Diff. actual ECT @ cylinder head vs. ECT @ cylinder head @ start of DCYn.a. K Diff. actual ECT @ radiator outlet vs. ECT @ radiator outlet @ start of DCY < 256.0K Diff. actual AAT vs. AAT @ start of DCY < 256.0 K For time>= 1.0 s Depending on mean value condition Mean value of all temperature sensors @ cold start>= -256° C Number of valid sensors >= 2.0 [-] Depending on block heater / solar radiation detection Time after engine start >= 0.5 s Vehicle speed>= 22 mph For time>= 20.0 s Diff. actual IAT @ manifold vs. min. IAT @ manifold < 5.0 K Diff. actual ECT @ cylinder head vs. min. ECT @ cylinder headn.a. K Diff. actual AAT vs. min. AAT< 4.0 K Diff. actual ECT @ radiator outlet vs. min. ECT @ radiator outlet< 1.1 K	0.1 s Once / DCY	2 DCY	-- Check the Intake Manifold Sensor -GX9-. Refer to Intake Manifold Sensor - GX9-, CHECKING .
P0112 Intake Air Temperature Sensor 1 Circuit Low Bank 1	Intake Air Temperature (IAT) Sensor Short To Ground	IAT sensor voltage < 0.10 V		0.5 s Continuous	2 DCY	-- Check the Intake Manifold Sensor -GX9-. Refer to Intake Manifold Sensor - GX9-, CHECKING .
P0113 Intake Air Temperature Sensor 1 Circuit High Bank 1	Intake Air Temperature (IAT) Sensor Open Circuit	IAT sensor voltage > 4.50 V		0.5 s Continuous	2 DCY	-- Check the Intake Manifold Sensor -GX9-. Refer to Intake Manifold Sensor - GX9-, CHECKING .
P0116 Engine Coolant Temperature Sensor 1 Circuit Range/Performance	Engine Coolant Temperature (ECT) Sensor @ Cylinder Head Rationality Check Low	Difference between modelled and measured cylinder block > 5.0 K	ECT @ cylinder head -128 - 127° C Time after engine start > 60.0 s	30.0 s Once / DCY	2 DCY	-- Check the Engine Coolant Temperature Sensor -G62-. Refer to Engine Coolant Temperature Sensor - G62-, CHECKING .-- Check the Engine Coolant Temperature Sensor on Radiator Outlet -G83-. Refer to Engine Coolant Temperature Sensor On Radiator Outlet - G83-, CHECKING .
	Engine Coolant Temperature (ECT) Sensor @ Cylinder Head Rationality Check Inappropriately Low	Diff. min temperature of cross check sensors vs. ECT @ cylinder head @ engine start >= 25° C	Cross checks finished	1.0 s Once / DCY
	Engine Coolant Temperature (ECT) Sensor @ Cylinder Head Rationality Check High	ECT @ cylinder head @ engine start > 40 - 80° C	Cross checks finished Engine running Engine off time >= 360.0 min Valid AAT signal for time >= 2.0 s Valid engine stop signal for time >= 2.0 s
		Difference between maximum and minimum temperature of < 1° C	ECT @ cylinder head > -256° C IAT @ throttle-48 - 143° C Depending on thermostat control: ECT @ cylinder head not calibrated ° C Or ECT @ cylinder head not calibrated ° C Engine not calibrated And Engine part load Or Engine full load Engine speed> 1, 300 RPM Vehicle speed>= 12 mph Engine load > 2.0% For time >= 20.0 - 43.0 s Engineidle Vehicle speed< 3 mph Or Fuel cut offactive Or Engine stop for time>= 20.0 - 43.0 s Time after engine start > 100.0 s
P0117 Engine Coolant Temperature Sensor 1 Circuit Low	Engine Coolant Temperature (ECT) Sensor @ Cylinder Head Short To Ground	ECT sensor voltage @ cylinder head < 0.30 V		0.5 s Continuous	2 DCY	-- Check the Engine Coolant Temperature Sensor -G62-. Refer to Engine Coolant Temperature Sensor - G62-, CHECKING .-- Check the Engine Coolant Temperature Sensor on Radiator Outlet -G83-. Refer to Engine Coolant Temperature Sensor On Radiator Outlet - G83-, CHECKING .
P0118 Engine Coolant Temperature Sensor 1 Circuit High	Engine Coolant Temperature (ECT) Sensor @ Cylinder Head Short To Battery / Open Circuit	ECT sensor voltage @ cylinder head > 4.90 V	IAT @ throttle >= -33° C Time after engine start > 60.0 s	0.5 s Continuous	2 DCY	-- Check the Engine Coolant Temperature Sensor -G62-. Refer to Engine Coolant Temperature Sensor - G62-, CHECKING .-- Check the Engine Coolant Temperature Sensor on Radiator Outlet -G83-. Refer to Engine Coolant Temperature Sensor On Radiator Outlet - G83-, CHECKING .
P0121 Throttle/Pedal Position Sensor/Switch "A" Circuit Range/Performance	Throttle Position Sensor (TPS) 1 Rationality Check	Difference between TPS 1 and TPS 2 > 6.499° TPS	Throttle adaptation (@ initial start or after detection of throttle exchange or checksum error) not active	0.3 s Continuous	2 DCY	-- Check the Throttle Valve Control Module -GX3-. Refer to Throttle Valve Control Module - GX3-, CHECKING .
	Throttle Position Sensor (TPS) 1 Rationality Check	Normalized difference between measured and modeled value of mass air flow from TPS 1 >= 1.0 [-] Or Relative mass air flow integral from TPS 1 > 60.0 [-]		0.01 s Continuous	2 DCY
P0122 Throttle/Pedal Position Sensor/Switch "A" Circuit Low	Throttle Position Sensor (TPS) 1 Short To Ground / Open Circuit	Throttle position sensor 1 voltage < 0.15 V		0.2 s Continuous	2 DCY	-- Check the Throttle Valve Control Module -GX3-. Refer to Throttle Valve Control Module - GX3-, CHECKING .
P0123 Throttle/Pedal Position Sensor/Switch "A" Circuit High	Throttle Position Sensor (TPS) 1 Short To Battery Plus	Throttle position sensor 1 voltage > 4.85 V		0.2 s Continuous	2 DCY	-- Check the Throttle Valve Control Module -GX3-. Refer to Throttle Valve Control Module - GX3-, CHECKING .
P0131 O2 Sensor Circuit Low Voltage Bank 1 Sensor 1	Oxygen Sensors (O2S) Front Short To Ground	O2S sensor voltage < 0.15 V	Engine running	0.5 s Continuous	2 DCY	-- Check the Oxygen Sensor 1 Before Catalytic Converter -GX10-. Refer to Oxygen Sensor 1 Before Catalytic Converter - GX10-, CHECKING .
P0132 O2 Sensor Circuit High Voltage Bank 1 Sensor 1	Oxygen Sensors (O2S) Front Short To Battery Voltage	O2S sensor voltage > 5.20 - 5.35 V	Engine running	0.5 s Continuous	2 DCY	-- Check the Oxygen Sensor 1 Before Catalytic Converter -GX10-. Refer to Oxygen Sensor 1 Before Catalytic Converter - GX10-, CHECKING .
P0133 O2 Sensor Circuit Slow Response Bank 1 Sensor 1	Oxygen Sensors (O2S) Front Dynamic Path Response Check	Case 1: With arithmetic filtering : average check Mean value of normalized signal amplitude not active [-] Or Ratio check Ratio of failed diagnostic cycle not active [-] Case 2: with EWMA filtering Mean value of normalized signal amplitude >= 1.10 [-]	Conditions range 1: (Standard parameters) General conditions: Time after engine start >= 0.0 s ECT @ cylinder head >= -48° C Vehicle speed>= 0 mph Integrated air mass after gear change 0.0 g MAF 0.0 mg/stk Integrated air mass per cylinder >= 0.0 kg Static conditions: O2S front ready Lambda stimulation active Lambda control value -35.0 - 35.0% Engine speed 928 - 3, 008 RPM MAF to activate diagnosis function 150.0 - 600.0 mg/stk MAF per segment > 18.0 kg/h Counter of integrated mass for fuel in oil < 255.0 [-] Catalyst purge not active Limited dynamic conditions: Integrated air mass after dynamic conditions are fulfilled not calibrated g Dynamic engine speed < 150 RPM Dynamic MAF not calibrated mg/stk Or Dynamic MAF per segment < 30.0 kg/h Dynamic lambda not calibrated % Change of dynamic torque < 0.07 [-] Conditions range 2: (Diagnosis carried out together with the catalyst efficiency diagnosis) General conditions Vehicle speed >= 22 mph BARO >= 0.0 kPa Catalyst overheating protection not active Turbine overheating protection not active O2S rear ready O2S heater rear active O2S front ready Internal resistance O2S rear <= 700.0 Ω Time after a catalyst purge phase >= 1.0 s Engine speed 1, 088 - 3, 008 RPM Deviation of lambda controller output @ start diagnosis < 10.0% Fast trim control ready Proportional part of secondary fuel control loop not calibrated % Coasting function not active Lambda adaptation not active Valve lift not active And Heat input conditions integrated Heat energy >= 550.0 - 700.0 kJ Or Time after engine start > 6, 553.5 s Or Time after first start of driving cycle > 6, 553.5 s And Depending on scavenging Integrated air mass after end of scavenging >= 50.0 g And Depending on lambda controller deviation Deviation of lambda controller set point and actual value during diagnosis < 10.0% Or Deviation of lambda controller output below set point during diagnosis < 6.0 - 22.8% Or Deviation of lambda controller output over set point during diagnosis < 7.0 - 25.0% And Temperature conditions ECT @ cylinder head > 60° C IAT @ manifold > -48° C Modeled catalyst temperature once after engine start > 510° C Modeled catalyst temperature @ start of diagnosis 500 - 800° C Modeled catalyst temperature during diagnosis 470 - 830° C Integrated air mass, catalyst temperature conditions fulfilled > 0.0 - not calibrated g Diff. between dynamic and stationary catalyst temperature @ start of diagnosis -100.0 K Diff. between dynamic and stationary catalyst temperature during diagnosis -150.0 - 150.0 K Modeled EGT @ O2S rear < 900° C Air mass conditions: Air mass @ start of diagnosis 89.99 - 1, 389.0 mg/stk Air mass during diagnosis not calibrated mg/stk MAF per cylinder @ start of diagnosis 28.0 - 150.0 kg/h MAF per cylinder during diagnosis not calibrated kg/h Load conditions: Air mass set point not calibrated mg/stk Engine load not calibrated % Accelerator pedal value not calibrated % For time not calibrated s And Low dynamic conditions: Dynamic engine speed < 50 RPM Dynamic air mass < 29.99 mg/stk Dynamic lambda controller output < 20.0% Integrated air mass after dynamic conditions are fulfilled > 20.0 g Evap purge conditions: Case 1 Evap purge valve not calibrated Case 2 Canister load calculation not calibrated Evap purge valve not calibrated Case 3 Canister load not calibrated [-] Evap purge valve not calibrated Close the gap conditions: O2S rear voltage @ diagnosis start >= 0.55 V Integrated air mass to start diagnosis >= 0.0 g O2S front dynamic diagnosis separate not active	4.4 s Once / DCY	1 DCY	-- Check the Oxygen Sensor 1 Before Catalytic Converter -GX10-. Refer to Oxygen Sensor 1 Before Catalytic Converter - GX10-, CHECKING .
P0133 O2 Sensor Circuit Slow Response Bank 1 Sensor 1	Oxygen Sensors (O2S) Front Delay Path Response Check	Normalized lambda controller value vs. modeled lambda value >= 1.10 [-]	General conditions: O2S front ready Time after engine start >= 0.0 s MAF to activate diagnosis function 0.0 mg/stk Integrated air mass per cylinder >= 0.3 - 2.0 kg Vehicle speed >= 0 mph Static condition Engine speed 1, 216 - 3, 008 RPM MAF per cylinder 20.0 - 150.0 kg/h Vehicle speed >= 3 mph Dynamic conditions Dynamic engine speed < 288 RPM Dynamic torque < 80.0 Nm Absolute dynamic MAF < 70.0 kg/h Activation due to canister purge Canister purge no purge Or Canister purge not active Or Canister purge wait ramp open Or Canister purge min purge And Canister load known Or Canister purge not calibrated And Moving mean value canister load <= 1.80 [-]	4.4 s Once / DCY	1 DCY
P0135 O2 Sensor Heater Circuit Bank 1 Sensor 1	Oxygen Sensors (O2S) Heater Front Functional Check	O2S ceramic temp. < 630° C	Actuator commanded on For time >= 10.0 s	20.0 s Continuous	2 DCY	-- Check the Oxygen Sensor 1 Before Catalytic Converter -GX10-. Refer to Oxygen Sensor 1 Before Catalytic Converter - GX10-, CHECKING .
P0137 O2 Sensor Circuit Low Voltage Bank 1 Sensor 2	Oxygen Sensors (O2S) Rear Short To Ground	O2S sensor voltage < 0.15 V	O2S heater active	0.5 s Continuous	2 DCY	-- Check the Oxygen Sensor 1 After Catalytic Converter -GX7-. Refer to Oxygen Sensor 1 After Catalytic Converter - GX7-, CHECKING .
P0138 O2 Sensor Circuit High Voltage Bank 1 Sensor 2	Oxygen Sensors (O2S) Rear Short To Battery	O2S sensor voltage > 5.2 - 5.35 V	O2S heater active	0.5 s Continuous	2 DCY	-- Check the Oxygen Sensor 1 After Catalytic Converter -GX7-. Refer to Oxygen Sensor 1 After Catalytic Converter - GX7-, CHECKING .
P013A O2 Sensor Slow Response - Rich to Lean Bank 1 Sensor 2	Oxygen Sensors (O2S) Rear Rich To Lean Transition Response Check	Case 1: with arithmetic filtering Gradient sensor voltagenot calibrated mV/s Or Gradient sensor voltage not calibrated mV/s Case 2: with EWMA filtering Gradient sensor voltage < 900.0 mV/s	General conditions: Vehicle speed>= 22 mph BARO >= 0.0 kPa Catalyst overheating protectionnot active Turbine overheating protection not active O2S rear ready O2S heater rear active O2S front ready Internal resistance O2S rear <= 700.0 Ω Time after a catalyst purge phase >= 1.0 s Integrated heat energy >= 550.0 - 700.0 kJ Or Time after engine start > 6, 553.5 s Engine speed 1, 088 - 3, 008 RPM Lambda control value < 50.0% Deviation of lambda controller output @ start diagnosis < 10.0% Fast trim control ready Proportional part of secondary fuel control loop not calibrated [-] Coasting function not active Lambda adaptation not active Valve lift not equipped Number of checks not calibrated [-] Counter of integrated mass for fuel in oil < 255.0 [-] And Depending on scavenging integrated air mass after end of scavenging >= 50.0 g And Depending on lambda controller deviation Deviation of lambda controller set point and actual value during diagnosis < 10.0% Or Deviation of lambda controller output below set point during diagnosis < 6.0 - 22.8% Or Deviation of lambda controller output over set point during diagnosis < 7.0 - 25.0% And Temperature conditions: ECT @ cylinder head > 60° C IAT @ manifold > -48° C Modeled catalyst temperature once after engine start > 510° C Modeled catalyst temperature @ start of diagnosis 500 - 800° C Modeled catalyst temperature during diagnosis 470 - 830° C Integrated air mass, catalyst temperature conditions fulfilled not calibrated g Diff. between dynamic and stationary catalyst temperature @ start of diagnosis -100.0 - 100.0 K Diff. between dynamic and stationary catalyst temperature during diagnosis -150.0 - 150.0 K Modeled EGT @ O2S rear <= 900° C Air mass conditions air mass @ start of diagnosis 89.99 - 1, 389.0 mg/stk Air mass during diagnosis not calibrated mg/stk MAF per cylinder @ start of diagnosis 28.0 - 150.0 kg/h MAF per cylinder during diagnosis not calibrated kg/h Load conditions: Air mass set point not calibrated mg/stk Engine load not calibrated % Accelerator pedal value not calibrated % For time not calibrated s And Low dynamic conditions Dynamic engine speed < 50 RPM Dynamic air mass < 29.99 mg/stk Dynamic lambda controller output < 20.0% Integrated air mass after dynamic conditions are fulfilled > 20.0 g Evap purge conditions: Case 1 Evap purge valve not calibrated Case 2 Canister load calculation not calibrated Evap purge flow not calibrated Case 3 Canister load not calibrated [-] Evap purge flow not calibrated Close the gap conditions O2S rear voltage @ diagnosis start >= 0.55 V Integrated air mass to start diagnosis >= 0.0 g O2S front dynamic diagnosis separate not active Gradient rich to lean diagnosis conditions Internal resistance O2S rear <= 700.0 Ω Modeled catalyst temperature once after engine start >= 0.0 - 1, 775° C Modeled EGT @ O2S rear >= 0.0 - 1, 775° C MAF per cylinder @ start of diagnosis 0.0 - 2, 047.97 kg/h	0.0 (FTP75: 50.0) s Once / DCY	1 DCY	-- Check the Oxygen Sensor 1 After Catalytic Converter -GX7-. Refer to Oxygen Sensor 1 After Catalytic Converter - GX7-, CHECKING .
P013B O2 Sensor Slow Response - Lean to Rich Bank 1 Sensor 2	Oxygen Sensors (O2S) Rear Lean To Rich Transition Response Check	Case 1: with arithmetic filtering Gradient sensor voltagenot calibrated mV/s Or Gradient sensor voltage not calibrated mV/s Case 2: with EWMA filtering Gradient sensor voltage < 650.0 mV/s	General conditions: Vehicle speed>= 22 mph BARO >= 0.0 kPa Catalyst overheating protectionnot active Turbine overheating protection not active O2S rear ready O2S heater rear active O2S front ready Internal resistance O2S rear <= 700.0 Ω Time after a catalyst purge phase >= 1.0 s Integrated heat energy >= 550.0 - 700.0 kJ Or Time after engine start > 6, 553.5 s Engine speed 1, 088 - 3, 008 RPM Lambda control value < 50.0% Deviation of lambda controller output @ start diagnosis < 10.0% Fast trim control ready Proportional part of secondary fuel control loop not calibrated [-] Coasting function not active Lambda adaptation not active Valve lift not equipped Number of checks not calibrated [-] Counter of integrated mass for fuel in oil < 255.0 [-] And Depending on scavenging Integrated air mass after end of scavenging >= 50.0 g And Depending on lambda controller deviation Deviation of lambda controller set point and actual value during diagnosis < 10.0% Or Deviation of lambda controller output below set point during diagnosis < 6.0 - 22.8% Or Deviation of lambda controller output over set point during diagnosis < 7.0 - 25.0% And Temperature conditions: ECT @ cylinder head > 60° C IAT @ manifold > -48° C Modeled catalyst temperature once after engine start > 510° C Modeled catalyst temperature @ start of diagnosis 500 - 800° C Modeled catalyst temperature during diagnosis 470 - 830° C Integrated air mass, catalyst temperature conditions fulfilled not calibrated g Diff. between dynamic and stationary catalyst temperature @ start of diagnosis -100.0 - 100.0 K Diff. between dynamic and stationary catalyst temperature during diagnosis -150.0 - 150.0 K Modeled EGT @ O2S rear <= 900° C Air mass conditions air mass @ start of diagnosis 89.99 - 1, 389.0 mg/stk Air mass during diagnosis not calibrated mg/stk MAF per cylinder @ start of diagnosis 28.0 - 150.0 kg/h MAF per cylinder during diagnosis not calibrated kg/h Load conditions: Air mass set point not calibrated mg/stk Engine load not calibrated % Accelerator pedal value not calibrated % For time not calibrated s And Low dynamic conditions Dynamic engine speed < 50 RPM Dynamic air mass < 29.99 mg/stk Dynamic lambda controller output < 20.0% Integrated air mass after dynamic conditions are fulfilled > 20.0 g Evap purge conditions: Case 1 Evap purge valve not calibrated Case 2 Canister load calculation not calibrated Evap purge flow not calibrated Case 3 Canister load not calibrated [-] Evap purge flow not calibrated Close the gap conditions O2S rear voltage @ diagnosis start >= 0.55 V Integrated air mass to start diagnosis >= 0.0 g O2S front dynamic diagnosis separate not active Gradient lean to rich diagnosis conditions Internal resistance O2S rear <= 700.0 Ω Modeled catalyst temperature once after engine start >= 0.0 - 1, 775° C Modeled EGT @ O2S rear >= 0.0 - 1, 775° C MAF per cylinder @ start of diagnosis 0.0 - 2, 047.97 kg/h	0.0 (FTP75: 50.0) s Once / DCY	1 DCY	-- Check the Oxygen Sensor 1 After Catalytic Converter -GX7-. Refer to Oxygen Sensor 1 After Catalytic Converter - GX7-, CHECKING .
P013E O2 Sensor Delayed Response - Rich to Lean Bank 1 Sensor 2	Oxygen Sensors (O2S) Rear Delayed Response Monitoring, Delay Measurement	Sensor signal delay time > 0.9 s	General conditions: Intrusive lambda ramp requestnot active Catalyst monitor lambda modulation request active Vehicle speed>= 22 mph Barometric pressure>= 0.0 kPa Catalyst overheating protection not active Turbine overheating protection not active O2S rear ready O2S front ready Internal resistance O2S rear <= 700.0 Ω ECT @ cylinder head > 60° C IAT @ manifold > -48° C Modeled catalyst temperature @ start of diagnosis> 510° C Modeled catalyst temperature @ during diagnosis470 - 830° C Diff. between dynamic and stationary catalyst temperature -150 - 150° C Integrated air mass, catalyst temp. conditions fulfilled>= 0.0 g Modeled EGT @ O2S rear<= 900° C MAF per cylinder28.0 - 150.0 kg/h Air mass, lower range >= 89.99 - 100.0 mg/stk Air mass, upper range <= 650.0 - 1, 389.0 mg/stk And Engine load not calibrated % Air mass set point not calibrated g/stk Accelerator pedal valuenot calibrated % For timenot calibrated s Depending on scavenging: Integrated air mass after end of scavenging >= 50.0 g And Low dynamic conditions Dynamic engine speed< 50 RPM Dynamic air mass < 29.99 mg/stk Dynamic lambda controller output< 20.0% And Integrated air mass after dynamic conditions are fulfilled > 20.0 g Time after a catalyst purge phase>= 1.0 s O2S rear voltage @ diagnosis start>= 0.55 V Integrated air mass >= 0.0 g Engine speed1, 088 - 3, 008 RPM Deviation of lambda controller output < 50.0% Proportional part of secondary fuel control loopnot calibrated % Coasting functionnot active O2S heater rear active Lambda adaptation not active Valve lift not active And Heat input conditions Integrated heat energy >= 550.0 - 700.0 kJ Or Time after engine start not calibrated s Or Time after first start of driving cycle > 6, 553.5 s And Depending on Lambda control: Sum of integral and proportional part of secondary fuel control loop before diagnosis < 0.10 [-] Or Sum of integral and proportional part of secondary fuel control loop during diagnosis < 0.25 [-] Depending on canister purge: Canister load not calibrated [-] Evap purge flow not calibrated Or Canister load calculation not calibrated Evap purge flow not calibrated Or Evap purge valvenot calibrated Or Evap purge valvenot calibrated Or Evap purgenot calibrated Or Depending on canister purge closing: Canister purge (conditions) not calibrated Canister purge valve (closing time)not calibrated s And Choice of: Evap purge valvenot calibrated Or Evap purge valvenot calibrated And Modeled air mass integral> 50.0 g Integrated air mass per cylinder>= 1.40 - 1.70kg	0.0 (FTP 75: 50.0) s Once / DCY	1 DCY	-- Check the Oxygen Sensor 1 After Catalytic Converter -GX7-. Refer to Oxygen Sensor 1 After Catalytic Converter - GX7-, CHECKING .
P013F O2 Sensor Delayed Response - Lean to Rich Bank 1 Sensor 2	Oxygen Sensors (O2S) Rear Delayed Response Monitoring, Delay Measurement	Sensor signal delay time > 1.5 s	General conditions: Intrusive lambda ramp requestnot active Catalyst monitor lambda modulation request active Vehicle speed>= 22 mph Barometric pressure>= 0.0 kPa Catalyst overheating protection not active Turbine overheating protection not active O2S rear ready O2S front ready Internal resistance O2S rear <= 700.0 Ω ECT @ cylinder head > 60° C IAT @ manifold > -48° C Modeled catalyst temperature @ start of diagnosis> 510° C Modeled catalyst temperature @ during diagnosis470 - 830° C Diff. between dynamic and stationary catalyst temperature -150 - 150° C Integrated air mass, catalyst temp. conditions fulfilled>= 0.0 g Modeled EGT @ O2S rear<= 900° C MAF per cylinder28.0 - 150.0 kg/h Air mass, lower range >= 89.99 - 100.0 mg/stk Air mass, upper range <= 650.0 - 1, 389.0 mg/stk And Engine load not calibrated % Air mass set point not calibrated g/stk Accelerator pedal valuenot calibrated % For timenot calibrated s Depending on scavenging: Integrated air mass after end of scavenging >= 50.0 g And Low dynamic conditions Dynamic engine speed< 50 RPM Dynamic air mass < 29.99 mg/stk Dynamic lambda controller output< 20.0% And Integrated air mass after dynamic conditions are fulfilled > 20.0 g Time after a catalyst purge phase>= 1.0 s O2S rear voltage @ diagnosis start>= 0.55 V Integrated air mass >= 0.0 g Engine speed1, 088 - 3, 008 RPM Deviation of lambda controller output < 50.0% Proportional part of secondary fuel control loopnot calibrated % Coasting functionnot active O2S heater rear active Lambda adaptation not active Valve lift not active And Heat input conditions Integrated heat energy >= 550.0 - 700.0 kJ Or Time after engine start not calibrated s Or Time after first start of driving cycle > 6, 553.5 s And Depending on Lambda control: Sum of integral and proportional part of secondary fuel control loop before diagnosis < 0.10 [-] Or Sum of integral and proportional part of secondary fuel control loop during diagnosis < 0.25 [-] Depending on canister purge: Canister load not calibrated [-] Evap purge flow not calibrated Or Canister load calculation not calibrated Evap purge flow not calibrated Or Evap purge valvenot calibrated Or Evap purge valvenot calibrated Or Evap purgenot calibrated Or Depending on canister purge closing: Canister purge (conditions) not calibrated Canister purge valve (closing time)not calibrated s And Choice of: Evap purge valvenot calibrated Or Evap purge valvenot calibrated And Modeled air mass integral> 50.0 g Integrated air mass per cylinder>= 1.40 - 1.70kg	0.0 (FTP75: 50.0) s Once / DCY	1 DCY	-- Check the Oxygen Sensor 1 After Catalytic Converter -GX7-. Refer to Oxygen Sensor 1 After Catalytic Converter - GX7-, CHECKING .
P0140 O2 Sensor Circuit No Activity Detected Bank 1 Sensor 2	Oxygen Sensors (O2S) Rear Open Circuit	Internal resistance of O2S (binary) > 25, 000.0 Ω		2.5 s Continuous	2 DCY	-- Check the Oxygen Sensor 1 After Catalytic Converter -GX7-. Refer to Oxygen Sensor 1 After Catalytic Converter - GX7-, CHECKING .
P0141 O2 Sensor Heater Circuit Bank 1 Sensor 2	Oxygen Sensors (O2S) Heater Rear Out Of Range High	Internal resistance of O2S (binary) 700.0 - 25, 000.0 Ω	Actuatorcommanded on For time >= 10.0 s	20.0 s Once / DCY	2 DCY	-- Check the Oxygen Sensor 1 After Catalytic Converter -GX7-. Refer to Oxygen Sensor 1 After Catalytic Converter - GX7-, CHECKING .
P0149 Fuel Timing Error	Fuel Injection Valve Supply Voltage Out Of Range Low	Boost voltage < 30.0 V	Engine running >= 0.3 s	3.6 s Continuous	2 DCY	-- Check the Engine Control Module -J623-. Refer to appropriate repair information.
	Fuel Injection Valve Supply Voltage Out Of Range Low	Boost voltage <= 50.0 V
	Fuel Injection Valve Supply Voltage Out Of Range High	Boost voltage > 75.0 V
P0171 System Too Lean Bank 1	Fuel System Too Lean	Lambda controller output > 35.0%	Lambda control closed loop Air mass > 60.0 mg/stk Engine speed > 576 RPM ECT @ cylinder head > 20° C IAT @ manifold > -48° C AAT > -48° C And Evap purge valveclosed Or Canister load <= 1.20 [-] Evap purge flow at max. value Or Depending on canister purge min: Lower limit of lambda controller output not calibrated Or Upper limit of lambda controller output not calibrated And Evap purge flow at min. value	25.0 s Continuous	2 DCY	-- Check the intake system visually for leaks (false air).-- Check the vacuum lines visually for leaks.-- Check the fuel pressure and delivery quantity. Refer to fuel system mechanical testing in PRELIMINARY CHECK and/or to appropriate repair information.-- Check the Fuel Pressure Sensor -G247-. Refer to Fuel Pressure Sensor - G247-, CHECKING -- Check the Fuel Injectors --. Refer to Fuel Injectors --, CHECKING -- Check the Oxygen Sensor 1 Before Catalytic Converter -GX10-. Refer to Oxygen Sensor 1 Before Catalytic Converter - GX10-, CHECKING .-- Check the Oxygen Sensor 1 After Catalytic Converter -GX7-. Refer to Oxygen Sensor 1 After Catalytic Converter - GX7-, CHECKING .-- Check the Fuel Delivery Unit -GX1- / Fuel Pump Control Module -J538-. Refer to Fuel Delivery Unit -GX1- / Fuel Pump Control Module -J538-, CHECKING .-- Check the Intake Manifold Sensor -GX9-. Refer to Intake Manifold Sensor - GX9-, CHECKING .
P0172 System Too Rich Bank 1	Fuel System Too Rich	Lambda controller output < -35.0%	Lambda control closed loop Mass air flow > 60.0 mg/stk Engine speed > 576 RPM ECT @ cylinder head > 20° C IAT @ manifold > -48° C AAT > -48° C Oil dilution not detected And Evap purge valveclosed Or Canister load <= 1.20 [-] Evap purge flow at max. value Or Depending on canister purge min: Lower limit of lambda controller output not calibrated Or Upper limit of lambda controller output not calibrated And Evap purge flow at min. value	60.0 s Continuous	2 DCY	-- Check the fuel pressure and delivery quantity. Refer to fuel system mechanical testing in PRELIMINARY CHECK and/or to appropriate repair information.-- Check the Fuel Pressure Sensor -G247-. Refer to Fuel Pressure Sensor - G247-, CHECKING -- Check the Fuel Injectors --. Refer to Fuel Injectors --, CHECKING -- Check the Oxygen Sensor 1 Before Catalytic Converter -GX10-. Refer to Oxygen Sensor 1 Before Catalytic Converter - GX10-, CHECKING .-- Check the Fuel Delivery Unit -GX1- / Fuel Pump Control Module -J538-. Refer to Fuel Delivery Unit -GX1- / Fuel Pump Control Module -J538-, CHECKING .-- Check the Intake Manifold Sensor -GX9-. Refer to Intake Manifold Sensor - GX9-, CHECKING .-- Check the EVAP Canister Purge Regulator Valve 1 -N80-. Refer to EVAP Canister Purge Regulator Valve 1 - N80-, CHECKING .
P0190 Fuel Pressure Regulator 1 Control Circuit/Open	Fuel Pressure LP Sensor Short To Battery / Open Circuit	High fuel pressure sensor voltage > 4.80 V		2.0 s Continuous	2 DCY	-- Check the Fuel Pressure Sensor -G247-. Refer to Fuel Pressure Sensor - G247-, CHECKING -- Check the Fuel Pressure Regulating Valve -N276-. Refer to Fuel Metering Valve - N290-, CHECKING .
P0191 Fuel Rail Pressure Sensor Circuit Range/Performance Bank 1	Fuel Rail Pressure (FRP) Out Of Range High	Fuel pressure > 26, 500.18 kPa	Engine speed > 512; < 6, 816 RPM Time after engine start > 10.0 s	5.0 s Continuous	2 DCY	-- Check the Fuel Pressure Sensor -G247-. Refer to Fuel Pressure Sensor - G247-, CHECKING .-- Check the Fuel Pressure Regulating Valve -N276-. Refer to Fuel Metering Valve - N290-, CHECKING .
P0192 Fuel Rail Pressure Sensor Circuit Low Bank 1	Fuel Pressure LP Sensor Short To Ground	High fuel pressure sensor voltage < 0.20 V		2.0 s Continuous	2 DCY	-- Check the Fuel Pressure Sensor -G247-. Refer to Fuel Pressure Sensor - G247-, CHECKING .-- Check the Fuel Pressure Regulating Valve -N276-. Refer to Fuel Metering Valve - N290-, CHECKING .
P01C4 Fuel Pressure Sensor "A" Circuit Range/Performance	Fuel Rail Pressure (FRP) Sensor Rationality Check Low	Deviation lambda of controller included adaptation < -22.50% And High pressure controller output > 40.0 mg	General: Engine speed 512 - 6, 816 RPM Fuel mass set point 5.0 - 1, 389.0 mg/stk Time after change to DFI not equipped s Time after engine start > 10.0 s Engine warm-up not active Catalyst heating not active Full load not active Catalyst purge not active Lambda control closed loop Evap purge functionality diagnosis not active Fuel pressure set point gradient <= 34, 777.60 kPa And Depending on low dynamic conditions: Fuel mass set point lower range > 5.0 mg/stk For time >= 10.0 s Fuel mass set point upper range < 187.17 - 229.23 mg/stk Fuel mass set point gradient -1, 389.0 - 1, 389.0 mg/stk For time >= 5.0 s And Depending on canister purge: Canister load <= 1.0 [-] Or Evap purge valve not active or closed	5.0 s Continuous	2 DCY	-- Check the Fuel Pressure Sensor -G247-. Refer to Fuel Pressure Sensor - G247-, CHECKING .-- Check the Fuel Pressure Regulating Valve -N276-. Refer to Fuel Metering Valve - N290-, CHECKING .
P01C4 Fuel Pressure Sensor "A" Circuit Range/Performance	Fuel Rail Pressure (FRP) Sensor Rationality Check High	Deviation lambda of controller included adaptation > 30.0% And High pressure controller output < -35.0 mg	General: Engine speed 608 - 6, 816 RPM Fuel mass set point 5.0 - 1, 389.0 mg/stk Time after change to DFI not equipped s Time after engine start > 10.0 s Engine warm-up not active Catalyst heating not active Full load not active Catalyst purge not active Lambda control closed loop Evap purge functionality diagnosis not active Fuel pressure set point gradient <= 34, 777.60 kPa And Depending on low dynamic conditions: Fuel mass set point lower range > 5.0 mg/stk For time >= 10.0 s Fuel mass set point upper range < 187.17 - 229.23 mg/stk Fuel mass set point gradient -1, 389.0 - 1, 389.0 mg/stk For time >= 5.0 s And Depending on canister purge: Canister load <= 1.0 [-] Or Evap purge valve not active or closed	5.0 s Continuous	2 DCY
P0201 Cylinder 1 Injector "A" Circuit	Fuel Injection Valves Open Circuit	Fault pattern for open circuit via powerstage diagnosis detected Injector low side voltage < 2.0 V	Engine stop not active ECT @ cylinder head >= -30° C Engine speed < 7, 000 RPM Injection time >= 0.0 s	8, 640.0° CRK Continuous	2 DCY	-- Check the Fuel Injectors --. Refer to Fuel Injectors --, CHECKING .
	Fuel Injection Valves Short Circuit	Fault pattern for short circuit via powerstage diagnosis detected Injector current rise time during peak phase < 0.064 ms
	Fuel Injection Valves Electrical Error	Indeterminate fault pattern via powerstage diagnosis detected And Injector low side voltage < 2.0 V Injector low side switch current > 25.0 A Or Injector low side voltage < 2.0 V Injector high side switch current > 25.0 [-] Or Injector low side voltage < 2.0 V Injector low side switch current (hardware values) > 9.0 - 14.0 A Or Injector voltage < 2.0 V Injector low side switch current > 25.0 [-] Or Injector voltage < 2.0 V Injector low side switch current (hardware values) > 9.0 - 14.0 A Or Injector load resistance to ground and battery > 20.0 Ω Injector low side switch current > 25.0 A Or Injector load resistance to ground and battery > 20.0 Ω Injector high side switch current > 25.0 [-] Or Power stage temperature > 150° C	Engine running ECT @ cylinder head >= -30° C Engine speed < 7, 000 RPM Injection time >= 0.0 s
P0202 Cylinder 2 Injector "A" Circuit	Fuel Injection Valves Open Circuit	Fault pattern for open circuit via powerstage diagnosis detected Injector low side voltage < 2.0 V	Engine stop not active ECT @ cylinder head >= -30° C Engine speed < 7, 000 RPM Injection time >= 0.0 s	8, 640.0° CRK Continuous	2 DCY	-- Check the Fuel Injectors --. Refer to Fuel Injectors --, CHECKING .
	Fuel Injection Valves Short Circuit	Fault pattern for short circuit via powerstage diagnosis detected Injector current rise time during peak phase < 0.064 ms
	Fuel Injection Valves Electrical Error	Indeterminate fault pattern via powerstage diagnosis detected And Injector low side voltage < 2.0 V Injector low side switch current > 25.0 A Or Injector low side voltage < 2.0 V Injector high side switch current > 25.0 [-] Or Injector low side voltage < 2.0 V Injector low side switch current (hardware values) > 9.0 - 14.0 A Or Injector voltage < 2.0 V Injector low side switch current > 25.0 [-] Or Injector voltage < 2.0 V Injector low side switch current (hardware values) > 9.0 - 14.0 A Or Injector load resistance to ground and battery > 20.0 Ω Injector low side switch current > 25.0 A Or Injector load resistance to ground and battery > 20.0 Ω Injector high side switch current > 25.0 [-] Or Power stage temperature > 150° C	Engine running ECT @ cylinder head >= -30° C Engine speed < 7, 000 RPM Injection time >= 0.0 s
P0203 Cylinder 3 Injector "A" Circuit	Fuel Injection Valves Open Circuit	Fault pattern for open circuit via powerstage diagnosis detected Injector low side voltage < 2.0 V	Engine stop not active ECT @ cylinder head >= -30° C Engine speed < 7, 000 RPM Injection time >= 0.0 s	8, 640.0° CRK Continuous	2 DCY	-- Check the Fuel Injectors --. Refer to Fuel Injectors --, CHECKING .
	Fuel Injection Valves Short Circuit	Fault pattern for short circuit via powerstage diagnosis detected Injector current rise time during peak phase < 0.064 ms
	Fuel Injection Valves Electrical Error	Indeterminate fault pattern via powerstage diagnosis detected And Injector low side voltage < 2.0 V Injector low side switch current > 25.0 A Or Injector low side voltage < 2.0 V Injector high side switch current > 25.0 [-] Or Injector low side voltage < 2.0 V Injector low side switch current (hardware values) > 9.0 - 14.0 A Or Injector voltage < 2.0 V Injector low side switch current > 25.0 [-] Or Injector voltage < 2.0 V Injector low side switch current (hardware values) > 9.0 - 14.0 A Or Injector load resistance to ground and battery > 20.0 Ω Injector low side switch current > 25.0 A Or Injector load resistance to ground and battery > 20.0 Ω Injector high side switch current > 25.0 [-] Or Power stage temperature > 150° C	Engine running ECT @ cylinder head >= -30° C Engine speed < 7, 000 RPM Injection time >= 0.0 s
P0204 Cylinder 4 Injector "A" Circuit	Fuel Injection Valves Open Circuit	Fault pattern for open circuit via powerstage diagnosis detected Injector low side voltage < 2.0 V	Engine stop not active ECT @ cylinder head >= -30° C Engine speed < 7, 000 RPM Injection time >= 0.0 s	8, 640.0° CRK Continuous	2 DCY	-- Check the Fuel Injectors --. Refer to Fuel Injectors --, CHECKING .
	Fuel Injection Valves Short Circuit	Fault pattern for short circuit via powerstage diagnosis detected Injector current rise time during peak phase < 0.064 ms
	Fuel Injection Valves Electrical Error	Indeterminate fault pattern via powerstage diagnosis detected And Injector low side voltage < 2.0 V Injector low side switch current > 25.0 A Or Injector low side voltage < 2.0 V Injector high side switch current > 25.0 [-] Or Injector low side voltage < 2.0 V Injector low side switch current (hardware values) > 9.0 - 14.0 A Or Injector voltage < 2.0 V Injector low side switch current > 25.0 [-] Or Injector voltage < 2.0 V Injector low side switch current (hardware values) > 9.0 - 14.0 A Or Injector load resistance to ground and battery > 20.0 Ω Injector low side switch current > 25.0 A Or Injector load resistance to ground and battery > 20.0 Ω Injector high side switch current > 25.0 [-] Or Power stage temperature > 150° C	Engine running ECT @ cylinder head >= -30° C Engine speed < 7, 000 RPM Injection time >= 0.0 s
P0221 Throttle/Pedal Position Sensor/Switch "B" Circuit Range/Performance	Throttle Position Sensor (TPS) 2 Rationality Check	Normalized difference between measured and modeled value of mass air flow from TPS 2 >= 1.0 [-] Or Relative mass air flow integral from TPS 2 > 60.0 [-]	Throttle adaptation (@ initial start or after detection of throttle exchange or checksum error) not active	0.01 s Continuous	2 DCY	-- Check the Throttle Valve Control Module -GX3-. Refer to Throttle Valve Control Module - GX3-, CHECKING .
P0222 Throttle/Pedal Position Sensor/Switch "B" Circuit Low	Throttle Position Sensor (TPS) 2 Short To Ground / Open Circuit	Throttle position sensor 2 voltage < 0.15 V		0.2 s Continuous	2 DCY	-- Check the Throttle Valve Control Module -GX3-. Refer to Throttle Valve Control Module - GX3-, CHECKING .
P0223 Throttle/Pedal Position Sensor/Switch "B" Circuit High	Throttle Position Sensor (TPS) 2 Short To Battery Plus	Throttle position sensor 2 voltage > 4.85 V		0.2 s Continuous	2 DCY	-- Check the Throttle Valve Control Module -GX3-. Refer to Throttle Valve Control Module - GX3-, CHECKING .
P0230 Fuel Pump Circuit	Fuel Pump Control Module (FPCM) Open Circuit	Phase current < 0.3 A For consecutive number of checks 20.0 [-]		1.7 s Continuous	2 DCY	-- Check the Fuel Delivery Unit -GX1- / Fuel Pump Control Module -J538-. Refer to Fuel Delivery Unit -GX1- / Fuel Pump Control Module -J538-, CHECKING .
P0230 Fuel Pump Circuit	Fuel Pump Control Module (FPCM) Short Circuit	Phase current >= 25.0 A		1.5 s Continuous	2 DCY
P0236 Turbocharger/Supercharger Boost Sensor "A" Circuit Range/Performance	Turbocharger (TC) Boost Pressure Sensor Engine Standing: Cross Check	Diff. turbocharger boost pressure vs. MAP > 8.50 kPa Diff. BARO vs. turbocharger boost pressure > 8.50 kPa Diff. BARO vs. MAP <= 8.50 kPa	Case 1: Engine stop during DCY Engine stopped Vehicle speed< 1 mph Engine @ driving cycle not calibrated For time >= 10.0 s Case 2: Engine stop @ start of DCY Engine stopped Vehicle speed < 1 mph Engine @ driving cycle not calibrated	3.0 s Continuous	2 DCY	-- Check the Charge Air Pressure Sensor -G31-. Refer to Charge Air Pressure Sensor - G31-, CHECKING -- Check the Charge Air Pressure Actuator -V465-. Refer to Charge Air Pressure Actuator - V465- / Charge Air Pressure Actuator Position Sensor - G581-, CHECKING .
	Turbocharger (TC) Boost Pressure Sensor ECM Keep Alive-Time: Cross Check		Engine stopped Vehicle speed< 1 mph ECM keep alive-time 10.0 - 6, 553.5 s Time after engine stop >= 5.0 s BARO sensor voltage 0.20 - 4.80 V MAP sensor voltage 0.20 - 4.80 V Boost pressure sensor voltage 0.20 - 4.80 V
	Turbocharger (TC) Boost Pressure Sensor Idle Speed: Cross Check	Diff. BARO vs. turbocharger boost pressure > 268.69 kPa Diff. turbocharger boost pressure > 10.0 kPa	Throttle position <= 119.500° TPS Engine speed <= 0 RPM And Time since idle speed > 10.0 s For time >= 10.0 s
	Turbocharger (TC) Boost Pressure Sensor Full Load: Cross Check	Diff. turbocharger boost pressure vs. MAP > 10.0 kPa Case 1: Diff. BARO vs. turbocharger boost pressure @ fuel cut off > 271.70 kPa Case 2: Diff. BARO vs. turbocharger boost pressure @ idle speed > 271.70 kPa	Engine speed 2, 000 - 8, 160 RPM Throttle position >= 27.353 - 78.004° TPS For time >= 2.0 s
P0237 Turbocharger/Supercharger Boost Sensor "A" Circuit Low	Turbocharger (TC) Boost Pressure Sensor Circuit Low	Turbocharger boost pressure sensor voltage < 0.20 V		0.5 s Continuous	2 DCY	-- Check the Charge Air Pressure Sensor -G31-. Refer to Charge Air Pressure Sensor - G31-, CHECKING .-- Check the Charge Air Pressure Actuator -V465-. Refer to Charge Air Pressure Actuator - V465- / Charge Air Pressure Actuator Position Sensor - G581-, CHECKING .
P0238 Turbocharger/Supercharger Boost Sensor "A" Circuit High	Turbocharger (TC) Boost pressure Sensor Circuit High	Turbocharger boost pressure sensor voltage > 4.80 V		0.5 s Continuous	2 DCY	-- Check the Charge Air Pressure Sensor -G31-. Refer to Charge Air Pressure Sensor - G31-, CHECKING .-- Check the Charge Air Pressure Actuator -V465-. Refer to Charge Air Pressure Actuator - V465- / Charge Air Pressure Actuator Position Sensor - G581-, CHECKING .
P025A Fuel Pump Module "A" Control Circuit/Open	Fuel Pump (FP) Open Circuit	Signal voltage, lower range > 1.92 - 2.21 V And Signal voltage, upper range < 2.84 - 3.25 V	Actuator commanded off	0.5 s Continuous	2 DCY	-- Check the Fuel Delivery Unit -GX1- / Fuel Pump Control Module -J538-. Refer to Fuel Delivery Unit -GX1- / Fuel Pump Control Module -J538-, CHECKING .
P025C Fuel Pump Module "A" Control Circuit Low	Fuel Pump (FP) Short To Ground	Signal voltage < 1.92 - 2.21 V	Actuator commanded off	3.0 s Continuous	2 DCY	-- Check the Fuel Delivery Unit -GX1- / Fuel Pump Control Module -J538-. Refer to Fuel Delivery Unit -GX1- / Fuel Pump Control Module -J538-, CHECKING .
P025D Fuel Pump Module "A" Control Circuit High	Fuel Pump (FP) Short To Battery Plus	Power stage temperature > 160 - 200° C Or Signal current > 100.0 - 180.0 mA	Actuator commanded on	0.5 s Continuous	2 DCY	-- Check the Fuel Delivery Unit -GX1- / Fuel Pump Control Module -J538-. Refer to Fuel Delivery Unit -GX1- / Fuel Pump Control Module -J538-, CHECKING .
P0261 Cylinder 1 Injector "A" Circuit Low	Fuel Injection Valves Short To Ground	Fault pattern for short to ground via powerstage diagnosis detected Injector voltage < 2.0 V	Engine stop not active ECT @ cylinder head >= -30° C Engine speed < 7, 000 RPM Injection time >= 0.0 s	8, 640.0° CRK Continuous	2 DCY	-- Check the Fuel Injectors --. Refer to Fuel Injectors --, CHECKING .
	Fuel Injection Valves Short To Ground (Low Side)	Injector driver voltage < 2.0 V And Injector driver high side switch < 25.0 A And Injector driver low side switch current < 25.0 A	Engine running ECT @ cylinder head >= -30° C Engine speed < 7, 000 RPM Injection time >= 0.0 ms	720° CRK Continuous
	Fuel Injection Valves Short To Ground (High Side)	Injector driver voltage < 2.0 V And Injector driver high side switch current > 25.0 A		720° CRK Continuous
P0262 Cylinder 1 Injector "A" Circuit High	Fuel Injection Valves Short To Battery Plus	Fault pattern for short to battery plus via powerstage diagnosis detected Injector voltage > 2.0 V	Engine stop not active ECT @ cylinder head >= -30° C Engine speed < 7, 000 RPM Injection time >= 0.0 s	8, 640.0° CRK Continuous	2 DCY	-- Check the Fuel Injectors --. Refer to Fuel Injectors --, CHECKING .
	Fuel Injection Valves Short To Battery Plus (Low Side)	Injector driver voltage > 2.0 V And Injector driver low side switch current > 25.0 A	Engine running ECT @ cylinder head >= -30° C Engine speed < 7, 000 RPM Injection time >= 0.0 s	720° CRK Continuous
	Fuel Injection Valves Short To Battery Plus (High Side)	Injector driver voltage > 2.0 V And Injector driver high side switch current > 25.0 A		720° CRK Continuous
P0264 Cylinder 2 Injector "A" Circuit Low	Fuel Injection Valves Short To Ground	Fault pattern for short to ground via powerstage diagnosis detected Injector voltage < 2.0 V	Engine stop not active ECT @ cylinder head >= -30° C Engine speed < 7, 000 RPM Injection time >= 0.0 s	8, 640.0° CRK Continuous	2 DCY	-- Check the Fuel Injectors --. Refer to Fuel Injectors --, CHECKING .
	Fuel Injection Valves Short To Ground (Low Side)	Injector driver voltage < 2.0 V And Injector driver high side switch < 25.0 A And Injector driver low side switch current < 25.0 A	Engine running ECT @ cylinder head >= -30° C Engine speed < 7, 000 RPM Injection time >= 0.0 ms	720° CRK Continuous
	Fuel Injection Valves Short To Ground (High Side)	Injector driver voltage < 2.0 V And Injector driver high side switch current > 25.0 A		720° CRK Continuous
P0265 Cylinder 2 Injector "A" Circuit High	Fuel Injection Valves Short To Battery Plus	Fault pattern for short to battery plus via powerstage diagnosis detected Injector voltage > 2.0 V	Engine stop not active ECT @ cylinder head >= -30° C Engine speed < 7, 000 RPM Injection time >= 0.0 s	8, 640.0° CRK Continuous	2 DCY	-- Check the Fuel Injectors --. Refer to Fuel Injectors --, CHECKING .
	Fuel Injection Valves Short To Battery Plus (Low Side)	Injector driver voltage > 2.0 V And Injector driver low side switch current > 25.0 A	Engine running ECT @ cylinder head >= -30° C Engine speed < 7, 000 RPM Injection time >= 0.0 s	720° CRK Continuous
	Fuel Injection Valves Short To Battery Plus (High Side)	Injector driver voltage > 2.0 V And Injector driver high side switch current > 25.0 A		720° CRK Continuous
P0267 Cylinder 3 Injector "A" Circuit Low	Fuel Injection Valves Short To Ground	Fault pattern for short to ground via powerstage diagnosis detected Injector voltage < 2.0 V	Engine stop not active ECT @ cylinder head >= -30° C Engine speed < 7, 000 RPM Injection time >= 0.0 s	8, 640.0° CRK Continuous	2 DCY	-- Check the Fuel Injectors --. Refer to Fuel Injectors --, CHECKING .
	Fuel Injection Valves Short To Ground (Low Side)	Injector driver voltage < 2.0 V And Injector driver high side switch < 25.0 A And Injector driver low side switch current < 25.0 A	Engine running ECT @ cylinder head >= -30° C Engine speed < 7, 000 RPM Injection time >= 0.0 ms	720° CRK Continuous
	Fuel Injection Valves Short To Ground (High Side)	Injector driver voltage < 2.0 V And Injector driver high side switch current > 25.0 A		720° CRK Continuous
P0268 Cylinder 3 Injector "A" Circuit High	Fuel Injection Valves Short To Battery Plus	Fault pattern for short to battery plus via powerstage diagnosis detected Injector voltage > 2.0 V	Engine stop not active ECT @ cylinder head >= -30° C Engine speed < 7, 000 RPM Injection time >= 0.0 s	8, 640.0° CRK Continuous	2 DCY	-- Check the Fuel Injectors --. Refer to Fuel Injectors --, CHECKING .
	Fuel Injection Valves Short To Battery Plus (Low Side)	Injector driver voltage > 2.0 V And Injector driver low side switch current > 25.0 A	Engine running ECT @ cylinder head >= -30° C Engine speed < 7, 000 RPM Injection time >= 0.0 s	720° CRK Continuous
	Fuel Injection Valves Short To Battery Plus (High Side)	Injector driver voltage > 2.0 V And Injector driver high side switch current > 25.0 A		720° CRK Continuous
P0270 Cylinder 4 Injector "A" Circuit Low	Fuel Injection Valves Short To Ground	Fault pattern for short to ground via powerstage diagnosis detected Injector voltage < 2.0 V	Engine stop not active ECT @ cylinder head >= -30° C Engine speed < 7, 000 RPM Injection time >= 0.0 s	8, 640.0° CRK Continuous	2 DCY	-- Check the Fuel Injectors --. Refer to Fuel Injectors --, CHECKING .
	Fuel Injection Valves Short To Ground (Low Side)	Injector driver voltage < 2.0 V And Injector driver high side switch < 25.0 A And Injector driver low side switch current < 25.0 A	Engine running ECT @ cylinder head >= -30° C Engine speed < 7, 000 RPM Injection time >= 0.0 ms	720° CRK Continuous
	Fuel Injection Valves Short To Ground (High Side)	Injector driver voltage < 2.0 V And Injector driver high side switch current > 25.0 A		720° CRK Continuous
P0271 Cylinder 4 Injector "A" Circuit High	Fuel Injection Valves Short To Battery Plus	Fault pattern for short to battery plus via powerstage diagnosis detected Injector voltage > 2.0 V	Engine stop not active ECT @ cylinder head >= -30° C Engine speed < 7, 000 RPM Injection time >= 0.0 s	8, 640.0° CRK Continuous	2 DCY	-- Check the Fuel Injectors --. Refer to Fuel Injectors --, CHECKING .
	Fuel Injection Valves Short To Battery Plus (Low Side)	Injector driver voltage > 2.0 V And Injector driver low side switch current > 25.0 A	Engine running ECT @ cylinder head >= -30° C Engine speed < 7, 000 RPM Injection time >= 0.0 s	720° CRK Continuous
	Fuel Injection Valves Short To Battery Plus (High Side)	Injector driver voltage > 2.0 V And Injector driver high side switch current > 25.0 A		720° CRK Continuous
P0300 Random/Multiple Cylinder Misfire Detected	Misfire Crankshaft Speed Fluctuation (Multiple)	Number of cylinders with emission threshold misfire within 4, 000 revolutions ≥ 2.0 [-] Or Number of cylinders with emission threshold misfire within 1, 000 revolutions ≥ 2.0 [-]	Emission threshold misfire detected	1, 000 rev Continuous	2 DCY	-- Check the spark plugs visually.-- Check the intake system visually for leaks.-- Check for an engine mechanical fault with a cylinder compression test. Carbon buildup may cause a higher than normal compression reading and may contribute to this concern. Refer to appropriate repair information for low compression readings or for carbon buildup removal.-- Check the fuel pressure and delivery quantity. Refer to fuel system mechanical testing in PRELIMINARY CHECK and/or to appropriate repair information.-- Check the Fuel Injectors --. Refer to Fuel Injectors --, CHECKING .-- Check the Ignition Coils with Power Output Stage --. Refer to Ignition Coils with Power Output Stage --, CHECKING .
P0300 Random/Multiple Cylinder Misfire Detected	Misfire Crankshaft Speed Fluctuation (Multiple)	Number of cylinders with catalyst damaging misfire ≥ 2.0 [-]	Catalyst damaging misfire detected	200 rev Continuous	Immediate
P0301 Cylinder 1 Misfire Detected	Misfire Crankshaft Speed Fluctuation (Single Or Multiple)	Catalyst damage misfire: Catalyst damaging misfire rate > 3.33 - 20.83%	Initial engine speed > 550 RPM Engine speed > 550 RPM Engine speed < 6, 848 RPM Time after engine start not calibrated s Engine load > 3.17 - 37.98% Depending on ECT @ cylinder head @ start ECT @ cylinder head @ engine start <= -48° C Then activation if ECT @ cylinder head >= 20° C Or ECT @ cylinder head @ engine start> -48° C And Fuel cut offnot active Or Single fuel cut offnot active Or Number of fade out cylinders < 2.0 [-] And Dynamic manifold air pressurenot calibrated kPa Dynamic throttle position not calibrated ° TPS/s And Dynamic of engine loadnot calibrated % And Engine not calibrated Engine speed not calibrated RPM Dynamic of ignition angle @ idle speed not calibrated ° CRK Or Dynamic of ignition angle not calibrated ° CRK And Rough road not detected	200 rev Continuous	Immediate	-- Check the spark plugs visually.-- Check the intake system visually for leaks.-- Check for an engine mechanical fault with a cylinder compression test. Carbon buildup may cause a higher than normal compression reading and may contribute to this concern. Refer to appropriate repair information for low compression readings or for carbon buildup removal.-- Check the fuel pressure and delivery quantity. Refer to fuel system mechanical testing in PRELIMINARY CHECK and/or to appropriate repair information.-- Check the Fuel Injectors --. Refer to Fuel Injectors --, CHECKING .-- Check the Ignition Coils with Power Output Stage --. Refer to Ignition Coils with Power Output Stage --, CHECKING .
		Emission threshold misfire within 1, 000 rev: Emission threshold misfire rate (MR) > 1.85%		1, 000 rev Continuous	2 DCY
		Emission threshold misfire within 4, 000 rev: Emission threshold misfire rate (MR) > 1.85%		4 x 1, 000 rev Continuous	2 DCY
P0302 Cylinder 2 Misfire Detected	Misfire Crankshaft Speed Fluctuation (Single Or Multiple)	Catalyst damage misfire: Catalyst damaging misfire rate > 3.33 - 20.83%	Initial engine speed > 550 RPM Engine speed > 550 RPM Engine speed < 6, 848 RPM Time after engine start not calibrated s Engine load > 3.17 - 37.98% Depending on ECT @ cylinder head @ start ECT @ cylinder head @ engine start <= -48° C Then activation if ECT @ cylinder head >= 20° C Or ECT @ cylinder head @ engine start> -48° C And Fuel cut offnot active Or Single fuel cut offnot active Or Number of fade out cylinders < 2.0 [-] And Dynamic manifold air pressurenot calibrated kPa Dynamic throttle position not calibrated ° TPS/s And Dynamic of engine loadnot calibrated % And Engine not calibrated Engine speed not calibrated RPM Dynamic of ignition angle @ idle speed not calibrated ° CRK Or Dynamic of ignition angle not calibrated ° CRK And Rough road not detected	200 rev Continuous	Immediate	-- Check the spark plugs visually.-- Check the intake system visually for leaks.-- Check for an engine mechanical fault with a cylinder compression test. Carbon buildup may cause a higher than normal compression reading and may contribute to this concern. Refer to appropriate repair information for low compression readings or for carbon buildup removal.-- Check the fuel pressure and delivery quantity. Refer to fuel system mechanical testing in PRELIMINARY CHECK and/or to appropriate repair information.-- Check the Fuel Injectors --. Refer to Fuel Injectors --, CHECKING .-- Check the Ignition Coils with Power Output Stage --. Refer to Ignition Coils with Power Output Stage --, CHECKING .
		Emission threshold misfire within 1, 000 rev: Emission threshold misfire rate (MR) > 1.85%		1, 000 rev Continuous	2 DCY
		Emission threshold misfire within 4, 000 rev: Emission threshold misfire rate (MR) > 1.85%		4 x 1, 000 rev Continuous	2 DCY
P0303 Cylinder 3 Misfire Detected	Misfire Crankshaft Speed Fluctuation (Single Or Multiple)	Catalyst damage misfire: Catalyst damaging misfire rate > 3.33 - 20.83%	Initial engine speed > 550 RPM Engine speed > 550 RPM Engine speed < 6, 848 RPM Time after engine start not calibrated s Engine load > 3.17 - 37.98% Depending on ECT @ cylinder head @ start ECT @ cylinder head @ engine start <= -48° C Then activation if ECT @ cylinder head >= 20° C Or ECT @ cylinder head @ engine start> -48° C And Fuel cut offnot active Or Single fuel cut offnot active Or Number of fade out cylinders < 2.0 [-] And Dynamic manifold air pressurenot calibrated kPa Dynamic throttle position not calibrated ° TPS/s And Dynamic of engine loadnot calibrated % And Engine not calibrated Engine speed not calibrated RPM Dynamic of ignition angle @ idle speed not calibrated ° CRK Or Dynamic of ignition angle not calibrated ° CRK And Rough road not detected	200 rev Continuous	Immediate	-- Check the spark plugs visually.-- Check the intake system visually for leaks.-- Check for an engine mechanical fault with a cylinder compression test. Carbon buildup may cause a higher than normal compression reading and may contribute to this concern. Refer to appropriate repair information for low compression readings or for carbon buildup removal.-- Check for an engine mechanical fault with a cylinder compression test. Carbon buildup may cause a higher than normal compression reading and may contribute to this concern. Refer to appropriate repair information for low compression readings or for carbon buildup removal.-- Check the fuel pressure and delivery quantity. Refer to fuel system mechanical testing in PRELIMINARY CHECK and/or to appropriate repair information.-- Check the Fuel Injectors --. Refer to Fuel Injectors --, CHECKING .-- Check the Ignition Coils with Power Output Stage --. Refer to Ignition Coils with Power Output Stage --, CHECKING .
		Emission threshold misfire within 1, 000 rev: Emission threshold misfire rate (MR) > 1.85%		1, 000 rev Continuous	2 DCY
		Emission threshold misfire within 4, 000 rev: Emission threshold misfire rate (MR) > 1.85%		4 x 1, 000 rev Continuous	2 DCY
P0304 Cylinder 4 Misfire Detected	Misfire Crankshaft Speed Fluctuation (Single Or Multiple)	Catalyst damage misfire: Catalyst damaging misfire rate > 3.33 - 20.83%	Initial engine speed > 550 RPM Engine speed > 550 RPM Engine speed < 6, 848 RPM Time after engine start not calibrated s Engine load > 3.17 - 37.98% Depending on ECT @ cylinder head @ start ECT @ cylinder head @ engine start <= -48° C Then activation if ECT @ cylinder head >= 20° C Or ECT @ cylinder head @ engine start> -48° C And Fuel cut offnot active Or Single fuel cut offnot active Or Number of fade out cylinders < 2.0 [-] And Dynamic manifold air pressurenot calibrated kPa Dynamic throttle position not calibrated ° TPS/s And Dynamic of engine loadnot calibrated % And Engine not calibrated Engine speed not calibrated RPM Dynamic of ignition angle @ idle speed not calibrated ° CRK Or Dynamic of ignition angle not calibrated ° CRK And Rough road not detected	200 rev Continuous	Immediate	-- Check the spark plugs visually.-- Check the intake system visually for leaks.-- Check for an engine mechanical fault with a cylinder compression test. Carbon buildup may cause a higher than normal compression reading and may contribute to this concern. Refer to appropriate repair information for low compression readings or for carbon buildup removal.-- Check the fuel pressure and delivery quantity. Refer to fuel system mechanical testing in PRELIMINARY CHECK and/or to appropriate repair information.-- Check the Fuel Injectors --. Refer to Fuel Injectors --, CHECKING .-- Check the Ignition Coils with Power Output Stage --. Refer to Ignition Coils with Power Output Stage --, CHECKING .
		Emission threshold misfire within 1, 000 rev: Emission threshold misfire rate (MR) > 1.85%		1, 000 rev Continuous	2 DCY
		Emission threshold misfire within 4, 000 rev: Emission threshold misfire rate (MR) > 1.85%		4 x 1, 000 rev Continuous	2 DCY
P0326 Knock / Combustion Vibration Sensor 1 Circuit Range/Performance Bank 1 or Single Sensor	Knock Sensor (KS) Rationality Check Low	For time >= 3.0 s Diff. between knock sensor signal and average knock sensor signal < 0.0 - 0.12 V	ECT @ cylinder head > 59° C Air mass > 229.0 mg/stk	4.3 s Continuous	2 DCY	-- Check the Knock Sensor 1 -G61-. Refer to Knock Sensor 1 - G61-, CHECKING .
P0327 Knock / Combustion Vibration Sensor 1 Circuit Low Bank 1 or Single Sensor	Knock Sensor (KS) Out Of Range	For time >= 0.8 s Sensor signal < 0.12 - 0.31 V	ECT @ cylinder head > 59° C Air mass > 229.0 mg/stk Engine speed > 2, 016 RPM	4.0 s Continuous	2 DCY	-- Check the Knock Sensor 1 -G61-. Refer to Knock Sensor 1 - G61-, CHECKING .
P0335 Crankshaft Position Sensor "A" Circuit	Crankshaft Position (CKP) Sensor Activity Check	Case 1: Counted exhaust camshaft signals without synchronization >= 17.0 [-] Or Counted intake camshaft signals without synchronization >= 17.0 [-] Case 2: Counted exhaust camshaft signals without synchronization not active [-] Or Counted intake camshaft signals not active [-]	Signal edges @ selected camshaft signal detected Choice of: Ignition off Engine speed > 380 RPM Engine stalling >= 1.0 s Or Synchronization test incorrect Or Engine speed >= 380 RPM Or Engine running Engine stalling >= 5.0 s Or Backwards rotation not detected Or Engine speed >= 400 RPM Engine stop active	0.01 s Continuous	2 DCY	-- Check the Engine Speed Sensor -G28-. Refer to Engine Speed Sensor - G28-, CHECKING .-- Check the Camshaft Position Sensor -G40-. Refer to Camshaft Position Sensor - G40-, CHECKING .
P0336 Crankshaft Position Sensor "A" Circuit Range/Performance	Engine Speed Sensor Out Of Range	Counted teeth vs. reference >= 1, 000, 000.0; <= 1, 000.0 μs	Engine running	3, 600.0° CRK Continuous	2 DCY	-- Check the Engine Speed Sensor -G28-. Refer to Engine Speed Sensor - G28-, CHECKING .-- Check the Camshaft Position Sensor -G40-. Refer to Camshaft Position Sensor - G40-, CHECKING .
	Crankshaft Position (CKP) Sensor Out Of Range	Segment adaptation >= 0.70%	Fuel cut off active Delay time >= 5, 760.0° CRK And Diff. actual air mass vs. previous air mass <= 20.01 - 39.99 mg/stk Engine load <= 20.0% Dynamic throttle position <= 269.50 - 398.40° TPS/s Rough road not detected Engine roughness signal not valid Segments in fuel cut-off mode >= 32.0 [-] Segment adaptation finished Engine speed 2, 496 - 5, 024 RPM 4 cylinder engine: Diff. between adapted value of cylinder 1 and cylinder 3 < 0.70% Diff. between adapted value of cylinder 2 and cylinder 4 < 0.70%	180.0° CRK Continuous
	Crankshaft Position (CKP) Rationality Check Low	Case 1: Engine speed > 3, 000 RPM Time between falling signal edges 0.0 - 50.0 μs Case 2: Engine speed <= 3, 000 RPM Time between signal edges < 30.0 μs	Engine speed >= 400 RPM	45, 720.0° CRK Continuous
	Crankshaft Position (CKP) Sensor Rationality Check	Counted teeth vs reference >= 1.0 [-]; <= 2.0 [-]	General conditions: Engine speed > 320 RPM And Case 1: Ignition off Engine speed > 380 RPM Engine stalling >= 1.0 s Or Case 2: Engine speed >= 380 RPM Or Engine running And Engine stalling >= 5.0 s Or Case 3: Backwards rotation not detected Or Case 4: Engine speed >= 400 RPM Engine stopped	1, 800.0° CRK Continuous
	Crankshaft Position (CKP) Sensor Rationality Check	Crankshaft reference gap not detected	General conditions: Reference gap of reluctor wheel detected And Case 1: Ignition off Engine speed > 380 RPM Engine stalling >= 1.0 s Or Case 2: Engine speed >= 380 RPM Or Engine running And Engine stalling >= 5.0 s Or Case 3: Backwards rotation not detected Or Case 4: Engine speed >= 400 RPM Engine stopped	2, 160.0° CRK Continuous
P0340 Camshaft Position Sensor "A" Circuit Bank 1 or Single Sensor	Camshaft Position (CMP) Intake Sensor Signal Activity Check	No change on signal >= 3.0 [-]	Engine speed >= 400 RPM	4, 680.0° CRK Continuous	2 DCY	-- Check the Engine Speed Sensor -G28-. Refer to Engine Speed Sensor - G28-, CHECKING .-- Check the Camshaft Position Sensor -G40-. Refer to Camshaft Position Sensor - G40-, CHECKING .
P0341 Camshaft Position Sensor "A" Circuit Range/Performance Bank 1 or Single Sensor	Camshaft Position (CMP) Intake Sensor Rationality Check	Ratio between measured segment time ratio and specified camshaft angle ratio > 2.75 [-] Or Ratio between measured segment time ratio and specified camshaft angle ratio < 0.36 [-] Or Offset between camshaft and crankshaft < -79.0° CRK Or Offset between camshaft and crankshaft > 15.0° CRK	Engine speed 400 - 8, 160 RPM	990.0° CRK Continuous	2 DCY	-- Check the Engine Speed Sensor -G28-. Refer to Engine Speed Sensor - G28-, CHECKING .-- Check the Camshaft Position Sensor -G40-. Refer to Camshaft Position Sensor - G40-, CHECKING .
	Camshaft Position (CMP) Intake Sensor Signal Activity Check	Segment time value < 50.0 μs	Engine speed 400 - 8, 160 RPM	1, 440.0° CRK Continuous
	Camshaft Position / Crankshaft Position (CMP/CKP) Intake Sensor Out Of Range	Offset between camshaft and crankshaft < -79.0° CRK Or Offset between camshaft and crankshaft > 15.0° CRK	Engine synchronization not validated Failure by exhaust camshaft detected	450.0° CRK Once / DCY
P0365 Camshaft Position Sensor "B" Circuit Bank 1	Camshaft Position (CMP) Exhaust Sensor Signal Activity Check	No change on signal>= 3.0 [-]	Engine speed >= 400 RPM	1, 080.00° CRK Continuous	2 DCY	-- Check the Camshaft Position Sensor 3 -G300-. Refer to Camshaft Position Sensor 3 - G300-, CHECKING .
P0366 Camshaft Position Sensor "B" Circuit Range/Performance Bank 1	Camshaft Position (CMP) Exhaust Sensor Rationality Check	Ratio between measured segment time ratio and specified camshaft angle ratio> 2.75 [-] Or Ratio between measured segment time ratio and specified camshaft angle ratio< 0.36 [-] Or Offset between camshaft and crankshaft< -24.0° CRK Or Offset between camshaft and crankshaft> 49.0° CRK	Engine speed400 - 8, 160RPM	990.0° CRK Continuous	2 DCY	-- Check the Camshaft Position Sensor 3 -G300-. Refer to Camshaft Position Sensor 3 - G300-, CHECKING .
	Camshaft Position (CMP) Exhaust Sensor Signal Activity Check	Segment time value< 50μs	Engine speed400 - 8, 160RPM	1, 440.0° CRK Continuous
	Camshaft Position / Crankshaft Position (CMP/CKP) Exhaust Sensor Out Of Range	Offset between camshaft and crankshaft< -24.0° CRK Or Offset between camshaft and crankshaft> 49.0° CRK	Engine synchronization via crankshaft and camshaft not finished Or Engine synchronization via crankshaft and camshaft lost	450.0° CRK Once / DCY"
P039B Cylinder 1 Pressure Too High	Knock Control Function Check	Slow detection: Ratio between knock sensor and knock threshold in main knock window > 2.0 - 3.0 [-] For time >= 9, 000.0 - 11, 700.0° CRK Or Ratio between knock sensor and noise level in pre knock window > 3.50 - 5.0 [-] For time >= 5, 760.0 - 6, 840.0° CRK Or Ratio between knock sensor and knock threshold in main knock window not calibrated [-] And Ratio between knock sensor and noise level in pre knock window not calibrated [-] For time not calibrated ° CRK Or Ratio between knock sensor and noise level in pre knock window > 3.5 - 5.0 [-] And Ratio between knock sensor and knock threshold in main knock window > 2.0 - 3.0 [-] For time >= 12, 960.0 - 16, 740.0° CRK Or Ratio between knock sensor and knock threshold in main knock window not calibrated [-] And Ratio between knock sensor and noise level in pre knock window not calibrated [-] And Ratio between knock sensor and knock threshold in main knock window not calibrated [-] For time not calibrated ° CRK Or Torque limitation factor < 0.80 [-]	Engine running ECT @ cylinder head > 59° C Engine speed 1, 216 - 6, 720 RPM Engine load not calibrated % Air mass > 501.0 - 599.0 mg/stk Delay time 0.0 seg And Dynamic engine speed not active	900.0° CRK Continuous	2 DCY	-- This DTC may set due to poor fuel quality or fuel that has aged excessively. If necessary, drain the fuel from the vehicle and replace with fresh fuel.-- Check the spark plugs visually for signs of fouling.-- Check for an engine mechanical fault with a cylinder compression test. Carbon buildup may cause a higher than normal compression reading and may contribute to this concern. Refer to appropriate repair information for low compression readings or for carbon buildup removal.-- Check the Knock Sensor 1 -G61-. Refer to Knock Sensor 1 - G61-, CHECKING .-- Check the Engine Speed Sensor -G28-. Refer to Engine Speed Sensor - G28-, CHECKING .
P039B Cylinder 1 Pressure Too High	Knock Control Function Check	Fast detection: Ratio between knock sensor and knock threshold in main knock window > 1.50 - 2.50 [-] For time >= 540.0° CRK Or Ratio between knock sensor and noise level in pre knock window > 2.75 - 4.50 [-] For time >= 360.0° CRK Case 1: Ratio between filtered engine roughness and misfire detection threshold <= 0.41 - 0.59 [-] Or Case 2: Ratio between normalized engine roughness and misfire detection threshold not calibrated [-] Or Case 3: Ratio between filtered engine roughness and misfire detection threshold not calibrated [-] Or Ratio between normalized engine roughness and misfire detection threshold not calibrated [-]	Engine running ECT @ cylinder head > 59° C Engine speed 1, 216 - 6, 720 RPM Engine load not calibrated % Air mass > 501.0 - 599.0 mg/stk Delay time 0.0 seg And Misfire detection active Dynamic engine speed not calibrated Previous cylinder shut-off not active	900.0° CRK Continuous	2 DCY
P03A5 Cylinder 2 Pressure Too High	Knock Control Function Check	Slow detection: Ratio between knock sensor and knock threshold in main knock window > 2.0 - 3.0 [-] For time >= 9, 000.0 - 11, 700.0° CRK Or Ratio between knock sensor and noise level in pre knock window > 3.50 - 5.0 [-] For time >= 5, 760.0 - 6, 840.0° CRK Or Ratio between knock sensor and knock threshold in main knock window not calibrated [-] And Ratio between knock sensor and noise level in pre knock window not calibrated [-] For time not calibrated ° CRK Or Ratio between knock sensor and noise level in pre knock window > 3.5 - 5.0 [-] And Ratio between knock sensor and knock threshold in main knock window > 2.0 - 3.0 [-] For time >= 12, 960.0 - 16, 740.0° CRK Or Ratio between knock sensor and knock threshold in main knock window not calibrated [-] And Ratio between knock sensor and noise level in pre knock window not calibrated [-] And Ratio between knock sensor and knock threshold in main knock window not calibrated [-] For time not calibrated ° CRK Or Torque limitation factor < 0.80 [-]	Engine running ECT @ cylinder head > 59° C Engine speed 1, 216 - 6, 720 RPM Engine load not calibrated % Air mass > 501.0 - 599.0 mg/stk Delay time 0.0 seg And Dynamic engine speed not active	900.0° CRK Continuous	2 DCY	-- This DTC may set due to poor fuel quality or fuel that has aged excessively. If necessary, drain the fuel from the vehicle and replace with fresh fuel.-- Check the spark plugs visually for signs of fouling.-- Check for an engine mechanical fault with a cylinder compression test. Carbon buildup may cause a higher than normal compression reading and may contribute to this concern. Refer to appropriate repair information for low compression readings or for carbon buildup removal.-- Check the Knock Sensor 1 -G61-. Refer to Knock Sensor 1 - G61-, CHECKING .-- Check the Engine Speed Sensor -G28-. Refer to Engine Speed Sensor - G28-, CHECKING
P03A5 Cylinder 2 Pressure Too High	Knock Control Function Check	Fast detection: Ratio between knock sensor and knock threshold in main knock window > 1.50 - 2.50 [-] For time >= 540.0° CRK Or Ratio between knock sensor and noise level in pre knock window > 2.75 - 4.50 [-] For time >= 360.0° CRK Case 1: Ratio between filtered engine roughness and misfire detection threshold <= 0.41 - 0.59 [-] Or Case 2: Ratio between normalized engine roughness and misfire detection threshold not calibrated [-] Or Case 3: Ratio between filtered engine roughness and misfire detection threshold not calibrated [-] Or Ratio between normalized engine roughness and misfire detection threshold not calibrated [-]	Engine running ECT @ cylinder head > 59° C Engine speed 1, 216 - 6, 720 RPM Engine load not calibrated % Air mass > 501.0 - 599.0 mg/stk Delay time 0.0 seg And Misfire detection active Dynamic engine speed not calibrated Previous cylinder shut-off not active	900.0° CRK Continuous	2 DCY
P03AF Cylinder 3 Pressure Too High	Knock Control Function Check	Slow detection: Ratio between knock sensor and knock threshold in main knock window > 2.0 - 3.0 [-] For time >= 9, 000.0 - 11, 700.0° CRK Or Ratio between knock sensor and noise level in pre knock window > 3.50 - 5.0 [-] For time >= 5, 760.0 - 6, 840.0° CRK Or Ratio between knock sensor and knock threshold in main knock window not calibrated [-] And Ratio between knock sensor and noise level in pre knock window not calibrated [-] For time not calibrated ° CRK Or Ratio between knock sensor and noise level in pre knock window > 3.5 - 5.0 [-] And Ratio between knock sensor and knock threshold in main knock window > 2.0 - 3.0 [-] For time >= 12, 960.0 - 16, 740.0° CRK Or Ratio between knock sensor and knock threshold in main knock window not calibrated [-] And Ratio between knock sensor and noise level in pre knock window not calibrated [-] And Ratio between knock sensor and knock threshold in main knock window not calibrated [-] For time not calibrated ° CRK Or Torque limitation factor < 0.80 [-]	Engine running ECT @ cylinder head > 59° C Engine speed 1, 216 - 6, 720 RPM Engine load not calibrated % Air mass > 501.0 - 599.0 mg/stk Delay time 0.0 seg And Dynamic engine speed not active	900.0° CRK Continuous	2 DCY	-- This DTC may set due to poor fuel quality or fuel that has aged excessively. If necessary, drain the fuel from the vehicle and replace with fresh fuel.-- Check the spark plugs visually for signs of fouling.-- Check for an engine mechanical fault with a cylinder compression test. Carbon buildup may cause a higher than normal compression reading and may contribute to this concern. Refer to appropriate repair information for low compression readings or for carbon buildup removal.-- Check the Knock Sensor 1 -G61-. Refer to Knock Sensor 1 - G61-, CHECKING .-- Check the Engine Speed Sensor -G28-. Refer to Engine Speed Sensor - G28-, CHECKING
P03AF Cylinder 3 Pressure Too High	Knock Control Function Check	Fast detection: Ratio between knock sensor and knock threshold in main knock window > 1.50 - 2.50 [-] For time >= 540.0° CRK Or Ratio between knock sensor and noise level in pre knock window > 2.75 - 4.50 [-] For time >= 360.0° CRK Case 1: Ratio between filtered engine roughness and misfire detection threshold <= 0.41 - 0.59 [-] Or Case 2: Ratio between normalized engine roughness and misfire detection threshold not calibrated [-] Or Case 3: Ratio between filtered engine roughness and misfire detection threshold not calibrated [-] Or Ratio between normalized engine roughness and misfire detection threshold not calibrated [-]	Engine running ECT @ cylinder head > 59° C Engine speed 1, 216 - 6, 720 RPM Engine load not calibrated % Air mass > 501.0 - 599.0 mg/stk Delay time 0.0 seg And Misfire detection active Dynamic engine speed not calibrated Previous cylinder shut-off not active	900.0° CRK Continuous	2 DCY
P03B9 Cylinder 4 Pressure Too High	Knock Control Function Check	Slow detection: Ratio between knock sensor and knock threshold in main knock window > 2.0 - 3.0 [-] For time >= 9, 000.0 - 11, 700.0° CRK Or Ratio between knock sensor and noise level in pre knock window > 3.50 - 5.0 [-] For time >= 5, 760.0 - 6, 840.0° CRK Or Ratio between knock sensor and knock threshold in main knock window not calibrated [-] And Ratio between knock sensor and noise level in pre knock window not calibrated [-] For time not calibrated ° CRK Or Ratio between knock sensor and noise level in pre knock window > 3.5 - 5.0 [-] And Ratio between knock sensor and knock threshold in main knock window > 2.0 - 3.0 [-] For time >= 12, 960.0 - 16, 740.0° CRK Or Ratio between knock sensor and knock threshold in main knock window not calibrated [-] And Ratio between knock sensor and noise level in pre knock window not calibrated [-] And Ratio between knock sensor and knock threshold in main knock window not calibrated [-] For time not calibrated ° CRK Or Torque limitation factor < 0.80 [-]	Engine running ECT @ cylinder head > 59° C Engine speed 1, 216 - 6, 720 RPM Engine load not calibrated % Air mass > 501.0 - 599.0 mg/stk Delay time 0.0 seg And Dynamic engine speed not active	900.0° CRK Continuous	2 DCY	-- This DTC may set due to poor fuel quality or fuel that has aged excessively. If necessary, drain the fuel from the vehicle and replace with fresh fuel.-- Check the spark plugs visually for signs of fouling.-- Check for an engine mechanical fault with a cylinder compression test. Carbon buildup may cause a higher than normal compression reading and may contribute to this concern. Refer to appropriate repair information for low compression readings or for carbon buildup removal.-- Check the Knock Sensor 1 -G61-. Refer to Knock Sensor 1 - G61-, CHECKING .-- Check the Engine Speed Sensor -G28-. Refer to Engine Speed Sensor - G28-, CHECKING
P03B9 Cylinder 4 Pressure Too High	Knock Control Function Check	Fast detection: Ratio between knock sensor and knock threshold in main knock window > 1.50 - 2.50 [-] For time >= 540.0° CRK Or Ratio between knock sensor and noise level in pre knock window > 2.75 - 4.50 [-] For time >= 360.0° CRK Case 1: Ratio between filtered engine roughness and misfire detection threshold <= 0.41 - 0.59 [-] Or Case 2: Ratio between normalized engine roughness and misfire detection threshold not calibrated [-] Or Case 3: Ratio between filtered engine roughness and misfire detection threshold not calibrated [-] Or Ratio between normalized engine roughness and misfire detection threshold not calibrated [-]	Engine running ECT @ cylinder head > 59° C Engine speed 1, 216 - 6, 720 RPM Engine load not calibrated % Air mass > 501.0 - 599.0 mg/stk Delay time 0.0 seg And Misfire detection active Dynamic engine speed not calibrated Previous cylinder shut-off not active	900.0° CRK Continuous	2 DCY
P0410 AIR System "A"	Secondary Air Injection (AIR) Functional Check	Diff. pressure value after secondary air injection vs. > 5.0 kPa	General: AIR pump ready Catalyst heating active AIR finished MAF <= 140.0 kg/h ECT @ cylinder head >= -10; < 115° C IAT @ manifold >= -10; < 100° C Modeled catalyst temperature < 900° C Relative barometric pressure > 0.73 [-] And Diff. BARO vs. MAP n.a. kPa Or Engine n.a.	0.1 s Once / DCY	2 DCY	-- Check the Secondary Air System -GX24-. Refer to Secondary Air Injection Sensor 1 - G609-, CHECKING .-- Check the Secondary Air Injection Pump Relay -J299- / Secondary Air Injection Pump Motor -V101-. Refer to Secondary Air Injection Pump Relay - J299- / Secondary Air Injection Pump Motor - V101-, CHECKING .
P0413 AIR System Switching Valve "A" Circuit Open	Secondary Air Injection (AIR) Valve Open Circuit	Output voltage, lower range >= 1.92 - 2.21 V Output voltage, upper range <= 2.85 - 3.25 V	Engine running Actuator commanded off	2.0 s Continuous	2 DCY	-- Check the Secondary Air System -GX24-. Refer to Secondary Air Injection Sensor 1 - G609-, CHECKING .
P0414 AIR System Switching Valve "A" Circuit Shorted	Secondary Air Injection (AIR) Valve Short To Ground	Output voltage < 1.92 - 2.21 V	Engine running Actuator commanded off	2.0 s Continuous	2 DCY	-- Check the Secondary Air System -GX24-. Refer to Secondary Air Injection Sensor 1 - G609-, CHECKING .
P0414 AIR System Switching Valve "A" Circuit Shorted	Secondary Air Injection (AIR) Valve Short To Battery Plus	Actuator temperature > 160 - 200° C Or Output current > 4.0 - 7.0 A	Engine running Actuator commanded on	2.0 s Continuous	2 DCY
P0418 AIR System Control "A" Circuit	Secondary Air Injection (AIR) Pump Relay Open Circuit	Output voltage lower range 1.92 - 2.21 V Output voltage upper range <= 2.85 - 3.25 V	Engine running Actuator commanded off	2.0 s Continuous	2 DCY	-- Check the Secondary Air Injection Pump Relay -J299- / Secondary Air Injection Pump Motor -V101-. Refer to Secondary Air Injection Pump Relay - J299- / Secondary Air Injection Pump Motor - V101-, CHECKING .
P0420 Catalyst System Efficiency Below Threshold Bank 1	Catalyst System NMOG / NMHC / NOX Conversion Capability	Arithmetic average Catalyst efficiency not calibrated [-] Or EWMA filtered Catalyst efficiency not calibrated [-] Or Arithmetic average, corrected with measured delay and transition time of oxygen sensors rear Catalyst efficiency not calibrated [-] Or EWMA filtered, corrected with measured delay and transition time of oxygen sensors rear Catalyst efficiency > 1.0 [-]	General conditions: Vehicle speed >= 22 mph BARO >= 0.0 kPa Catalyst overheating protection not active Turbine overheating protection not active O2S rear ready O2S heater rear active O2S front ready Internal resistance O2S rear <= 700.0 Ω Time after a catalyst purge phase >= 1.0 s Engine speed 1, 088 - 3, 008 RPM Lambda control value < 50.0% Deviation of lambda controller output to start diagnosis < 10.0% Deviation of lambda controller output during diagnosis < 7.0 - 24.99% Fast trim control ready Proportional part of secondary fuel control loop not calibrated % Coasting function not active Lambda adaptation not active Valve lift not equipped And Heat input conditions Integrated heat energy >= 550.0 - 700.0 kJ Or Time after engine start not calibrated s Or Time after first start of driving cycle > 6, 553.5 s And Depending on scavenging: Integrated air mass after end of scavenging >= 50.0 g Temperature conditions: ECT @ cylinder head > 60° C IAT @ manifold > -48° C Modeled catalyst temperature once after engine start > 510° C Modeled catalyst temperature to start diagnosis 500 - 800° C Modeled catalyst temperature during diagnosis 470 - 830° C Integrated air mass, catalyst temperature conditions fulfilled not calibrated g Diff. between dynamic and stationary catalyst temperature to start diagnosis -100.0 - 100.0 K Diff. between dynamic and stationary catalyst temperature during diagnosis -150.0 - 150.0 K Modeled EGT @ O2S rear <= 900° C Air mass conditions: Air mass to start diagnosis 89.99 - 1, 389.0 mg/stk Air mass during diagnosis not calibrated mg/stk MAF per cylinder to start diagnosis 28.0 - 150.0 kg/h MAF per cylinder during diagnosis not calibrated kg/h Load conditions: Air mass set point not calibrated mg/stk Engine load not calibrated % Accelerator pedal value not calibrated % For time not calibrated s And Low dynamic conditions: Dynamic engine speed < 50 RPM Dynamic air mass < 29.99 mg/stk Dynamic lambda controller output < 20.0% Integrated air mass after dynamic conditions are fulfilled > 20.0 g Evap purge conditions: Case 1 Evap purge valve not calibrated Case 2 Canister load calculation not calibrated Evap purge flow not calibrated Case 3 Canister load not calibrated [-] Evap purge flow not calibrated Close the gap conditions: O2S rear voltage @ diagnosis start >= 0.55 V Integrated air mass to start diagnosis >= 0.0 g O2S front dynamic diagnosis separate not active For arithmetic average value calculation: Number of checks required for valid result not calibrated [-] For EWMA-filter: Minimum number of tests per DCY required 1.0 Step change detection will initiate multiple tests per DCY Conditions for step change detection: Relative deviation between new measured value and old EWMA filtered value >= 0.30 - 2.0 [-] Number of checks 6.0 [-]	60.0 - 70.0 s Once / DCY	1 DCY	-- Check the Three Way Catalytic Converter (TWC). Refer to THREE WAY CATALYTIC CONVERTER (TWC), CHECKING .-- Check the Oxygen Sensor 1 After Catalytic Converter -GX7-. Refer to Oxygen Sensor 1 After Catalytic Converter - GX7-, CHECKING .-- Check the Oxygen Sensor 1 Before Catalytic Converter -GX10-. Refer to Oxygen Sensor 1 Before Catalytic Converter - GX10-, CHECKING .
P0441 EVAP System Incorrect Purge Flow	Evaporative Emission (EVAP) Canister Purge ValveFunctional Check: Stuck Close	Ratio actual intake manifold pressure and modeled set point < 0.10 [-]	ECT @ cylinder head > 60° C BARO > 73.0 kPa AAT > 4° C AAT @ start >= 5° C Diff. BARO vs. filtered MAP >= 20.0 kPa Diff. BARO vs. filtered MAP > 28.0 kPa Engine speed < 2, 800 RPM And Ratio MAF @ manifold and MAF max. > 0.07 - 0.10 [-] Engine speed1, 180 RPM Or Coasting function not calibrated And Vehicle speed >= 11mph Diff. engine speed vs. filtered engine speed < 90 RPM Diff. ratio MAF @ manifold and MAF max vs. ratio filtered MAF @ manifold and MAF max< 0.15 [-] Diff. modeled MAP vs. filtered modeled MAP < 1.50 - 2.50 kPa Integrated air mass since engine start >= 0.0 - 5, 000.0 g And Lambda conditions fullfilled Lambda control active Lambda control value -30.0 - 30.0% O2S front 0.90 - 1.10 [-] Or Fuel cut off not calibrated And Case 1: Integrated air mass @ canister purge per driving cycle not calibrated g Case 2: Ratio MAF @ canister purge and MAF per cylinder >= 0.0 [-] Or Canister purge sampling rate >= 20.0% And Integrated air mass @ canister purge valve>= 31.9 g Depending on AAT: AAT >= 30° C Canister load <= 0.20 [-] Or AAT >= 50; < 30° C Canister load <= 0.20 [-] Or AAT < 50° C Canister load <= 0.20 [-]	8.5 s Once / DCY	2 DCY	-- Check the EVAP Canister Purge Regulator Valve 1 -N80-. Refer to EVAP Canister Purge Regulator Valve 1 - N80-, CHECKING .-- Check the Fuel Tank Leak Detection Control Module -J909-. Refer to Fuel Tank Leak Detection Control Module - J909-, CHECKING .
P0444 EVAP System Purge Control Valve "A" Circuit Open	Evaporative Emission (EVAP) Canister Purge Valve Open Circuit	Output voltage, lower range >= 1.92 - 2.21 V Output voltage, upper range <= 2.85 - 3.25 V	Engine start not active Engine running Evap purge valve opening signal (PWM) > 3.13; <= 98.83% Actuator commanded off	2.0 s Continuous	2 DCY	-- Check the EVAP Canister Purge Regulator Valve 1 -N80-. Refer to EVAP Canister Purge Regulator Valve 1 - N80-, CHECKING .-- Check the Fuel Tank Leak Detection Control Module -J909-. Refer to Fuel Tank Leak Detection Control Module - J909-, CHECKING .
P0445 EVAP System Purge Control Valve "A" Circuit Shorted	Evaporative Emission (EVAP) Canister Purge Valve Short To Ground	Output voltage 1.92 - 2.21 V	Engine start not active Engine running Evap purge valve opening signal (PWM) <= 98.83% Actuator commanded off	2.0 s Continuous	2 DCY	-- Check the EVAP Canister Purge Regulator Valve 1 -N80-. Refer to EVAP Canister Purge Regulator Valve 1 - N80-, CHECKING .-- Check the Fuel Tank Leak Detection Control Module -J909-. Refer to Fuel Tank Leak Detection Control Module - J909-, CHECKING .
P0445 EVAP System Purge Control Valve "A" Circuit Shorted	Evaporative Emission (EVAP) Canister Purge Valve Short To Battery Plus	Actuator temperature 160 - 200° C Or Output current > 4.0 - 7.0 A	Engine start not active Engine running Evap purge valve opening signal (PWM) >= 3.13% Actuator commanded on	2.0 s Continuous	2 DCY
P0450 EVAP System Pressure Sensor/Switch Circuit	Natural Vacuum Leak Detection (NVLD) Switch Open Circuit	Signal voltage 0.39 - 0.55 V	Case 1: Engine running Case 2: Ignition off NVLD (EVAP-System) diagnostic mode active	0.5 s Continuous	2 DCY	-- Check the Fuel Tank Leak Detection Control Module -J909-. Refer to Fuel Tank Leak Detection Control Module - J909-, CHECKING .
P0451 EVAP System Pressure Sensor/Switch Circuit Range/Performance	Natural Vacuum Leak Detection (NVLD) Switch Functional Check Stuck Close	Natural vacuum leak detection (NVLD) switch position closed	Ignition off Fuel level < 85.10% Fuel temperature increase >= 5 K For time >= 1.0 h AAT >= 4° C Barometric pressure >= 73.0 kPa Time since ignition off > 20.0; < 1, 440.0 min	0.1 s Once / DCY	2 DCY	-- Check the Fuel Tank Leak Detection Control Module -J909-. Refer to Fuel Tank Leak Detection Control Module - J909-, CHECKING .
P0452 EVAP System Pressure Sensor/Switch Circuit Low	Natural Vacuum Leak Detection (NVLD) Switch Short To Ground	Signal voltage < 0.24 V	Case 1: Engine running Case 2: Ignition off NVLD (EVAP-System) diagnostic mode active	0.5 s Continuous	2 DCY	-- Check the Fuel Tank Leak Detection Control Module -J909-. Refer to Fuel Tank Leak Detection Control Module - J909-, CHECKING .
P0453 EVAP System Pressure Sensor/Switch Circuit High	Natural Vacuum Leak Detection (NVLD) Switch Short To Battery Plus	Signal voltage > 3.0 V	Case 1: Engine running Case 2: Ignition off NVLD (EVAP-System) diagnostic mode active	0.5 s Continuous	2 DCY	-- Check the Fuel Tank Leak Detection Control Module -J909-. Refer to Fuel Tank Leak Detection Control Module - J909-, CHECKING .
P0456 EVAP System Leak Detected (Very Small Leak)	Evaporative Emission (EVAP) System Very Small Leak Functional Check	Natural vacuum leak detection (NVLD) switch position open	Ignition off Fuel level < 85.10% Fuel temperature drop >= 6 K For time > 1.0 h AAT >= 4° C Barometric pressure > 73.0 kPa Diff. barometric pressure @ stop and barometric pressure @ start < 0.65 kPa Time since ignition off > 90.0 min; < 600.0 min	0.1 s Once / DCY	2 DCY	-- Check the EVAP System for Leaks. Refer to EVAP SYSTEM, CHECKING FOR LEAKS .-- Check the EVAP Canister Purge Regulator Valve 1 -N80-. Refer to EVAP Canister Purge Regulator Valve 1 - N80-, CHECKING .-- Check the Fuel Tank Leak Detection Control Module -J909-. Refer to Fuel Tank Leak Detection Control Module - J909-, CHECKING .
P0461 Fuel Level Sensor "A" Circuit Range/Performance	Fuel Level Sensor Plausibility Check	Diff. fuel consumption and fuel level changes < -239.0; > 12.0 l	General: Refueling or defueling not detected And Fuel tank level signal valid And Case 1: for tank full Fuel level >= 96.09% Fuel consumption since last refueling or last plausibility check > 44.0 l Case 2: for tank not full Fuel level < 96.09% Fuel consumption since last refueling or last plausibility check > 15.0 l	1.0 s Continuous	2 DCY	Check the Fuel Level Sensor -G-. Refer to appropriate repair information.
P0462 Fuel Level Sensor "A" Circuit Low	COM: Fuel Level (FL) Sensor 1 Communication With IPC	Instrument cluster module signal: circuit low failure		0.5 s Continuous	2 DCY	Check the Fuel Level Sensor -G-. Refer to appropriate repair information.
P0462 Fuel Level Sensor "A" Circuit Low	COM: Fuel Level (FL) Sensor 1 Communication With IPC	Instrument cluster module signal: signal range check failure		0.5 s Continuous	2 DCY
P0463 Fuel Level Sensor "A" Circuit High	COM: Fuel Level (FL) Sensor 1 Communication With IPC	Instrument cluster module signal: circuit high failure		0.5 s Continuous	2 DCY	Check the Fuel Level Sensor -G-. Refer to appropriate repair information.
P0491 AIR System Insufficient Flow Bank 1	Secondary Air Injection (AIR) Functional Check	Case 1: Blockage: ratio relative measured secondary air pressure and modelled secondary air pressure [tube blocked] < 0.70 [-] Or Leakage: ratio relative measured secondary air pressure and modelled secondary air pressure [leak diagnosis] < 0.65 [-] Case 2: Diff. expected integrated secondary air pressure pulsations and actual integrated secondary air pressure pulsations n.a. kPa/s Case 3: Blockage: ratio relative measured secondary air pressure and modelled secondary air pressure [tube blocked] < 0.40 [-] Or Leakage: ratio relative measured < 0.15 [-]	General: AIR pump active Catalyst heating active AIR active MAF <= 140.0 kg/h ECT @ cylinder head >= -10; < 115° C IAT @ manifold >= -10; < 100° C Modelled catalyst temperature < 900° C Relative barometric pressure > 0.73 [-] And Diff. BARO vs. MAP n.a. kPa Or Engine not running	0.1 s Once / DCY	2 DCY	-- Check the Secondary Air System -GX24-. Refer to Secondary Air Injection Sensor 1 - G609-, CHECKING .-- Check the Secondary Air Injection Pump Relay -J299- / Secondary Air Injection Pump Motor -V101-. Refer to Secondary Air Injection Pump Relay - J299- / Secondary Air Injection Pump Motor - V101-, CHECKING .
P0501 Vehicle Speed Sensor "A" Circuit Range/Performance	COM: Vehicle Speed Sensor (VSS) Communication With VSS	Speed sensor fault value: rationality check low failure		0.5 s Continuous	2 DCY	-- Check the vehicle speed signal. Refer to VEHICLE SPEED SIGNAL, CHECKING .
		Speed sensor fault value: rationality check high failure
		Speed sensor fault value: out of range low failure
		Speed sensor fault value: out of range high failure
P0502 Vehicle Speed Sensor "A" Circuit Low	Vehicle Speed Sensor (VSS) Short To Ground	Diagnostic signal from output driver failure		0.5 s Continuous	2 DCY	-- Check the vehicle speed signal. Refer to VEHICLE SPEED SIGNAL, CHECKING .
	Vehicle Speed Sensor (VSS) Open Circuit
	Vehicle Speed Sensor (VSS) Short To Battery Plus
P0506 Idle Control System RPM - Lower Than Expected	Idle Speed Control (ISC) Function Monitoring: Engine Speed Deviation	Diff. actual engine speed vs. engine speed set point < -100 RPM Integrated I-part of idle speed not calibrated	General conditions: Vehicle speed0 mph Accelerator pedalreleased by driver Throttle actuator commanded on Evap purge flow < 4.0 kg/h Engine running Time after engine start > 0.0 s Clutch switch not calibrated Barometric pressure> 70.0 kPa Catalyst heating not active ECT @ cylinder head > -48° C And Set point change not calibrated RPM For timenot calibrated s And Additional after dynamic conditions fulfilled: Gear switch not active (A/T only) Accelerator pedalreleased by driver Vehicle speed 0 mph Engine load< 31.25% (M/T only) For time>= 0.0 s	12.0 s Continuous	2 DCY	-- Check the Throttle Valve Control Module -GX3-. Refer to Throttle Valve Control Module - GX3-, CHECKING .
P0507 Idle Control System RPM - Higher Than Expected	Idle Speed Control (ISC) Function Monitoring: Engine Speed Deviation	Diff. actual engine speed vs. engine speed set point > 90 RPM Integrated I-part of idle speed not calibrated	General conditions: Vehicle speed0 mph Accelerator pedalreleased by driver Throttle actuator commanded on Evap purge flow < 4.0 kg/h Engine running Time after engine start > 0.0 s Clutch switch not calibrated Barometric pressure> 70.0 kPa Catalyst heating not active ECT @ cylinder head > -48° C And Set point change not calibrated RPM For timenot calibrated s And Additional after dynamic conditions fulfilled: Gear switch not active (A/T only) Accelerator pedalreleased by driver Vehicle speed0 mph For time>= 0.0 s	12.0 s Continuous	2 DCY	-- Check the Throttle Valve Control Module -GX3-. Refer to Throttle Valve Control Module - GX3-, CHECKING .
P050A Cold Start Idle Control System Performance	Cold Start Monitoring Idle Speed Control (ISC) Function Monitoring: Engine Speed Deviation	Diff. actual engine speed vs. engine speed set point < -100 RPM Integrated I-part of idle speed not calibrated	General conditions: Vehicle speed0 mph Accelerator pedalreleased by driver Throttle actuator commanded on Evap purge flow < 4.0 kg/h Engine running Time after engine start > 0.0 s Clutch switch not calibrated Barometric pressure> 70.0 kPa Catalyst heating active ECT @ cylinder head > -10° C And Set point change not calibrated RPM For time not calibrated s And Additional after dynamic conditions fulfilled: Gear switch not active (A/T only) Accelerator pedalreleased by driver Vehicle speed0 mph Engine load < 31.25% (M/T only) For time>= 0.0 s	12.0 s Continuous	2 DCY	-- Check the Throttle Valve Control Module -GX3-. Refer to Throttle Valve Control Module - GX3-, CHECKING .
P050A Cold Start Idle Control System Performance		Diff. actual engine speed vs. engine speed set point > 90 RPM Integrated I-part of idle speed controller not calibrated	General conditions: Vehicle speed= 0 mph Accelerator pedalreleased by driver Throttle actuator commanded on Evap purge flow < 4.0 kg/h Engine running Time after engine start > 0.0 s Clutch switch not calibrated Barometric pressure> 70.0 kPa Catalyst heating active ECT @ cylinder head > -10° C And Set point change not calibrated RPM For timenot calibrated s And Additional after dynamic conditions fulfilled: Gear switch not active (A/T only) Accelerator pedalreleased by driver Vehicle speed0 mph For time>= 0.0 s	12.0 s Continuous	2 DCY
P050B Cold Start Ignition Timing Performance	Cold Start Monitoring Ignition Control (IC) Ignition Timing Monitor	Ratio between ignition angle efficiency integral and time at > 0.20 [-]	Engine idle speed Ignition angle efficiency set point <= 0.85 [-] Modeled pressure quotient <= 1.0 [-] Barometric pressure > 0.0 kPa Catalyst heating active Engine start temperature -10 - 80° C Time after engine start > 2.0 s Vehicle speed 0 mph And Diff. air mass set point vs. filtered air mass set point for load dynamic detection < 99, 999.0 mg/stk For time >= 0.0 s And Diff. engine speed vs. filtered engine speed for engine speed dynamic detection < 8, 160 RPM For time >= 0.0 s	5.0 s Once / DCY	2 DCY	-- Check for any engine speed sensor or ignition coil faults and diagnose them first. If no other codes are set, replace the Engine Control Module -J623-. Refer to appropriate repair information.-- Check the Throttle Valve Control Module -GX3-. Refer to Throttle Valve Control Module - GX3-, CHECKING .
P052A Cold Start "A" Camshaft Position Timing Over-Advanced Bank 1	Cold Start Monitoring Variable Valve Timing (VVT) Rationality Check	Camshaft position deviation> 9.0° CRK	Modeled oil temperature-40 - 160° C Engine speed608 - 6, 016RPM Camshaft position not calibrated Camshaft position adjustmentactive Catalyst heating active Camshaft position deviation integrator (actual vs. set point position)>= 8.0° CRK*s	0.0 (FTP75: 45.0) s Once / DCY	2 DCY	-- Check the Camshaft Adjustment Valve 1 -N205-. Refer to Camshaft Adjustment Valve 1 - N205-, CHECKING .
P053F Cold Start Fuel Pressure Performance Bank 2	Cold Start Monitoring Fuel System Out Of Range Low	Deviation between set point and actual fuel pressure > 2, 999.80 kPa For time >= 3.0 s	General: Engine speed> 512 RPM Time after engine start > 10.0 s And Fuel mass set point lower range > 5.0 mg/stk For time>= 10.0 s Fuel mass set point upper range<= 187.17 - 229.23 mg/stk Fuel mass set point gradient -1, 389.0 - 1, 389.0 mg/stk For time>= 5.0 s And Additional for catalyst heating: Catalyst heating active ECT @ cylinder head > -48° C Fuel mass set point lower range>= 5.0 mg/stk For time>= 5.1 s	4.5 s Once / DCY	2 DCY	-- Check the fuel pressure and delivery quantity. Refer to fuel system mechanical testing in PRELIMINARY CHECK and/or to appropriate repair information.-- Check the Fuel Delivery Unit -GX1- / Fuel Pump Control Module -J538-. Refer to Fuel Delivery Unit -GX1- / Fuel Pump Control Module -J538-, CHECKING .-- Check the Fuel Metering Valve -N290-. Refer to Fuel Metering Valve - N290-, CHECKING .-- Check the Fuel Pressure Sensor -G247-. Refer to Fuel Pressure Sensor - G247-, CHECKING .
P053F Cold Start Fuel Pressure Performance Bank 2	Cold Start Monitoring Fuel System Out Of Range High	Deviation between set point and actual fuel pressure < -2, 999.90 kPa For time >= 3.0 s		4.5 s Once / DCY	2 DCY
P054A Cold Start "B" Camshaft Position Timing Over-Advanced Bank 1	Cold Start Monitoring Variable Valve Timing (VVT) Rationality Check	Camshaft position deviation > 9.0° CRK	Modeled oil temperature-40 - 160° C Engine speed 608 - 6, 016 RPM Camshaft position not calibrated Camshaft position adjustmentactive Catalyst heating active Camshaft position deviation integrator (actual vs. set point position)>= 8.0° CRK's	0.0 (FTP75: 45.0) s Once / DCY	2 DCY	-- Check the Exhaust Camshaft Adjustment Valve 1 -N318-. Refer to Exhaust Camshaft Adjustment Valve 1 - N318-, CHECKING .
P0601 Internal Control Module Memory Checksum Error	Engine Control Module (ECM): Checksum Verification	Calibration checksum incorrect		1.0 s Continuous	2 DCY	-- Check the Engine Control Module -J623-. Refer to appropriate repair information.
P0601 Internal Control Module Memory Checksum Error	Engine Control Module (ECM): Checksum Verification	Software checksum incorrect		1.0 s Continuous	2 DCY
P0603 Internal Control Module Keep Alive Memory (KAM) Error	Engine Control Module (ECM): Communication Check	Device 2: SPI communication with ATIC failure		2.0 s Continuous	2 DCY	-- Check the Engine Control Module -J623-. Refer to appropriate repair information.
		Device 1: SPI communication with ATIC failure
		SPI communication with ATIC failure


	Engine Control Module (ECM): Fuel Injection Valves Internal Hardware Check	Time reference from micro controller during initialization failure		4.9 s Once / DCY

		Hardware during initialization failure
		Hardware during initialization failure
		Calibration during initialization failure
		Calibration during initialization failure
		Hardware vs. software version check during initialization failure

		Communication between micro controller and SDI - Driver power stage failure		2, 880.0° CRK Continuous
				2, 880.0° CRK Continuous
				360.0° CRK Once / DCY
				360.0° CRK Once / DCY
		Time reference from micro controller during initialization missing		2, 880.0° CRK Continuous
				2, 880.0° CRK Continuous
		Communication between micro controller and SDI - Driver power stage failed		4, 320.0° CRK Continuous
				4, 320.0° CRK Continuous
P0606 Control Module Processor	Barometric Pressure (BARO) Sensor Engine Standing: Cross Check	Case 1: charged engine Diff. BARO vs. MAP > 8.50 kPa Diff. BARO vs. turbocharger boost pressure > 8.50 kPa Case 2: non charged engine Diff. BARO mean value vs. MAP mean value not calibrated kPa Diff. deviation BARO mean value to mean value (MAP mean value, BARO mean value, BARO @ ECM keep alive time and MAP @ ECM keep alive time) not calibrated kPa Diff. deviation MAP mean value not calibrated kPa	Case A: engine stop during DCY Engine stopped Vehicle speed < 1 mph Engine @ driving cycle not calibrated For time >= 10.0 s Case B: engine stop @ start of DCY Engine stopped Vehicle speed < 1 MPH Engine @ driving cycle not calibrated	3.0 s Continuous	2 DCY	-- NOTE: The BARO sensor is an internal part of the ECM and is not repairable. If the BARO reading is off by more than 10%, replace the Engine Control Module -J623-. Refer to appropriate repair information.
	Barometric Pressure (BARO) Sensor ECM Keep Alive-Time: Cross Check	Diff. BARO vs. MAP> 8.50 kPa Diff. BARO vs. turbocharger > 8.50 kPa	Engine stopped Vehicle speed < 1 mph ECM keep alive-time > 10.0 - 6, 553.5 s Time after engine stop >= 5.0 s BARO sensor voltage 0.20 - 4.80 V MAP sensor voltage 0.20 - 4.80 V Boost pressure sensor voltage 0.20 - 4.80 V
	Barometric Pressure (BARO) Sensor Full Load Cross Check	Diff. turbocharger boost pressure vs. MAP <= 10.0 kPa Case 1: Diff. BARO vs. turbocharger boost pressure @ fuel cut off not calibrated kPa Or Case 2: Diff. BARO vs. turbocharger boost pressure @ idle speed not calibrated kPa	Engine running Engine speed 2, 000 - 8, 160 RPM Throttle position >= 27.353 - 78.004° TPS For time >= 2.0 s
	Barometric Pressure (BARO) Sensor Out Of Range Low	Measured barometric pressure < 45.0 kPa		5.0 s Continuous
	Barometric Pressure (BARO) Sensor Out Of Range High	Measured barometric pressure > 115.0 kPa		5.0 s Continuous
	Knock Control Functional Check	Knock control failure	Engine running	6.4 s Continuous
	Engine Control Module (ECM): Analog / Digital Converter Function Monitoring: A/D Converter	Diff. A/D-channel 1 vs. A/D channel 2 > 0.30 V		0.5 s Continuous
	Engine Control Module (ECM): Communication Check	SPI communication with ATIC implausible	Time after ignition on >= 1.0 s	10.0 s Continuous
	Engine Control Module (ECM): Communication Check	SPI communication with ATIC failed	Time after ignition on >= 1.0 s	10.0 s Continuous
	Engine Control Module (ECM): EEPROM Check	EEPROM information failure		1.0 s Continuous
		Communication between sample software and production hardware error		1.0 s Once / DCY
		Finished NVM Crypt integrity error
		Decryption of NVM Crypt failed
	Engine Control Module (ECM): RAM Functional Check	Monitoring module check failed		0.5 s Continuous
	CAN: Controller RAM Check	RAM error memory checksum error	Initialization phase active Ignition on	0.2 s Once / DCY
P0607 Control Module Performance	Barometric Pressure (BARO) Sensor Short To Ground	Barometric pressure sensor voltage < 0.20 V		0.5 s Continuous	2 DCY	-- NOTE: The BARO sensor is an internal part of the ECM and is not repairable. If the BARO reading is off by more than 10%, replace the Engine Control Module -J623-. Refer to appropriate repair information.
P0607 Control Module Performance	Barometric Pressure (BARO) Sensor Short To Battery Plus	Barometric pressure sensor voltage > 4.80 V		0.5 s Continuous	2 DCY
P060C Internal Control Module Main Processor Performance	Engine Control Module (ECM): Electronic Throttle Control Module Function Monitoring: Injection	Fuel mass validation failed		0.5 s Continuous	2 DCY	-- Check the Throttle Valve Control Module -GX3-. Refer to Throttle Valve Control Module - GX3-, CHECKING .
	Engine Control Module (ECM): Electronic Throttle Control Module Function Monitoring: Accelerator Position	Comparison voltage sensor 1 with sensor 2 implausible
	Engine Control Module (ECM): Electronic Throttle Control Module Function Monitoring: Torque	Validation of torque losses failed
		Validation min. torque @ clutch failed
		Validation max. torque @ clutch failed
		Validation idle speed engine torque (I-Part) failed
		Validation engine torque failed
		Validation idle speed engine torque (PD-Part) failed
	Engine Control Module (ECM): Electronic Throttle Control Module Function Monitoring: Engine Speed Deviation	Engine speed validation failed
	Engine Control Module (ECM): Electronic Throttle Control Module Function Monitoring: Throttle Position	Comparison voltage sensor 1 with sensor 2 implausible
P0638 Throttle Actuator Control Range/Performance Bank 1	Throttle Actuator Adaptation Value Monitoring	Battery voltage <= 9.04 V	Throttle adaptation (@ initial start or after detection of throttle exchange or checksum error) active	0.01 s Once Per Lifetime	2 DCY	-- Check the Throttle Valve Control Module -GX3-. Refer to Throttle Valve Control Module - GX3-, CHECKING .
		Accelerator pedal value > 99.90% Or Engine speed > 64 RPM Or Vehicle speed > 1 mph Or IAT @ throttle < 5° C Or ECT @ cylinder head < 5° C Or ECT @ cylinder head > 110° C		0.01 s Once Per Lifetime
		Actual TPS ref. point > 0.503° TPS	Throttle adaptation demanded Accelerator pedal value < 99.90% Engine speed < 64 RPM Vehicle speed < 1 mph IAT @ throttle > 5° C ECT @ cylinder head 5 - 110° C	0.01 s Once / DCY
		Actual TPS 1 or 2 voltage - voltage ref. point > 0.07 V		0.01 s Once / DCY
	Throttle Actuator Monitoring Of Position	Actual TPS 1 or 2 voltage - voltage ref. point > 0.07 V		0.01 s Once Per Lifetime
		Actual TPS - ref. point > 0.503° TPS
		Actual TPS 1 or 2 voltage - voltage ref. point > 0.25 V
		Actual TPS 1 or 2 voltage - voltage ref. point > 0.07 V
		Throttle position sensor 1 voltage < 0.40 V Or Throttle position sensor 2 voltage > 4.60 V Or Throttle position sensor 1 voltage > 0.80 V Or Throttle position sensor 2 voltage < 4.20 V
		Actual TPS - ref. point > 0.503° TPS
P0642 Sensor Reference Voltage "A" Circuit Low	Engine Control Module (ECM): 5V Supply Voltage Out Of Range Low	Analog output 1 supply voltage < 4.62 V		0.2 s Continuous	2 DCY	-- If a related sensor voltage code is also set, refer to that sensor for diagnosis first. If no other related codes set, replace the Engine Control Module -J623-. Refer to appropriate repair information.
P0643 Sensor Reference Voltage "A" Circuit High	Engine Control Module (ECM): 5V Supply Voltage Out Of Range High	Analog output 1 supply voltage > 5.43 V		0.2 s Continuous	2 DCY	-- If a related sensor voltage code is also set, refer to that sensor for diagnosis first. If no other related codes set, replace the Engine Control Module -J623-. Refer to appropriate repair information.
P064A Fuel Pump Control Module	Fuel Pump Control Module (FPCM) Over-Temperature Warning Power Stage	Power stage temperature > 125° C		1.0 s Continuous	2 DCY	-- Check the Fuel Delivery Unit -GX1- / Fuel Pump Control Module -J538-. Refer to Fuel Delivery Unit -GX1- / Fuel Pump Control Module -J538-, CHECKING .
P064A Fuel Pump Control Module	Fuel Pump Control Module (FPCM) Functional Check: Electronics	Internal check failed		0.7 s Continuous	2 DCY
P0652 Sensor Reference Voltage "B" Circuit Low	Engine Control Module (ECM): 5V Supply Voltage Out Of Range Low	Analog output 2 supply voltage < 4.62 V		0.2 s Continuous	2 DCY	-- If a related sensor voltage code is also set, refer to that sensor for diagnosis first. If no other related codes set, replace the Engine Control Module -J623-. Refer to appropriate repair information.
P0653 Sensor Reference Voltage "B" Circuit High	Engine Control Module (ECM): 5V Supply Voltage Out Of Range High	Analog output 2 supply voltage > 5.43 V		0.2 s Continuous	2 DCY	-- If a related sensor voltage code is also set, refer to that sensor for diagnosis first. If no other related codes set, replace the Engine Control Module -J623-. Refer to appropriate repair information.
P0657 Actuator Supply Voltage "A" Circuit/Open	Engine Components Supply Voltage Relay Open Circuit	Output voltage, lower range >= 1.90 - 2.30 V Output voltage, upper range <= 2.80 - 3.20V	Actuator commanded off	1.0 s Continuous	2 DCY	-- Check the Motronic Engine Control Module Power Supply Relay -J271-. Refer to Motronic Engine Control Module Power Supply Relay - J271-, CHECKING .-- Check the Engine Component Power Supply Relay -J757-. Refer to Engine Component Power Supply Relay - J757-, CHECKING .
P0658 Actuator Supply Voltage "A" Circuit Low	Engine Components Supply Voltage Relay Short To Ground	Output voltage < 1.90 - 2.30 V	Actuator commanded off	1.0 s Continuous	2 DCY	-- Check the Motronic Engine Control Module Power Supply Relay -J271-. Refer to Motronic Engine Control Module Power Supply Relay - J271-, CHECKING .-- Check the Engine Component Power Supply Relay -J757-. Refer to Engine Component Power Supply Relay - J757-, CHECKING
P0659 Actuator Supply Voltage "A" Circuit High	Engine Components Supply Voltage Relay Short To Battery Voltage	Output current > 1.0 - 2.3 A Or Actuator temperature > 175 - 195° C	Actuator commanded on	1.0 s Continuous	2 DCY	-- Check the Motronic Engine Control Module Power Supply Relay -J271-. Refer to Motronic Engine Control Module Power Supply Relay - J271-, CHECKING .-- Check the Engine Component Power Supply Relay -J757-. Refer to Engine Component Power Supply Relay - J757-, CHECKING .
P0686 ECM/PCM Power Relay Control Circuit Low	Main Relay Rationality Check During Engine Off	Sensed circuit voltage > 6.0V	Actuator commanded off For time>= 0.3 s	0.1 s Continuous	2 DCY	-- Check the Motronic Engine Control Module Power Supply Relay -J271-. Refer to Motronic Engine Control Module Power Supply Relay - J271-, CHECKING .
P0687 ECM/PCM Power Relay Control Circuit High	Main Relay Rationality Check During Engine Running	Sensed circuit voltage < 5.0 V	Actuator commanded on For time>= 0.1 s	0.1 s Continuous	2 DCY	-- Check the Motronic Engine Control Module Power Supply Relay -J271-. Refer to Motronic Engine Control Module Power Supply Relay - J271-, CHECKING .
P0687 ECM/PCM Power Relay Control Circuit High	Main Relay Short To Battery Plus	Main relay driver temperature > 175 - 195° C Or Main relay output current > 1.0 - 2.3 A	Actuator commanded on For time>= 0.4 s	0.2 s Continuous	2 DCY
P0698 Sensor Reference Voltage "C" Circuit Low	Engine Control Module (ECM): 5V Supply Voltage Out Of Range Low	Analog output 3 supply voltage < 4.62 V		0.2 s Continuous	2 DCY	-- If a related sensor voltage code is also set, refer to that sensor for diagnosis first. If no other related codes set, replace the Engine Control Module -J623-. Refer to appropriate repair information.
P0699 Sensor Reference Voltage "C" Circuit High	Engine Control Module (ECM): 5V Supply Voltage Out Of Range High	Analog output 3 supply voltage > 5.43 V		0.2 s Continuous	2 DCY	-- If a related sensor voltage code is also set, refer to that sensor for diagnosis first. If no other related codes set, replace the Engine Control Module -J623-. Refer to appropriate repair information.
P11A1 Camshaft Actuator "A" Cylinder 1 Circuit/Open	Variable Valve Lift (VVL) Open Circuit	Output voltage, lower range< 1.92 - 2.21 V Output voltage, upper range> 2.85 - 3.25 V	Actuator commanded off	0.5 s Continuous	2 DCY	-- Check the Cam Adjustment Actuators --. Refer to Cam Adjustment Actuators --, CHECKING .
P11A1 Camshaft Actuator "A" Cylinder 1 Circuit/Open	Variable Valve Lift (VVL) Short To Ground	Output voltage< 1.92 - 2.21V	Actuator commanded off	0.5 s Continuous	2 DCY
P11A2 Camshaft Actuator "A" Cylinder 1 Range/Performance	Variable Valve Lift (VVL) Rationality Check Low	Actuator feedback signal voltage permanently low [-]	Modeled oil temperature< 20° C	6.0 seg Continuous	2 DCY	-- Check the Cam Adjustment Actuators --. Refer to Cam Adjustment Actuators --, CHECKING .
P11A3 Camshaft Actuator "B" Cylinder 1 Circuit/Open	Variable Valve Lift (VVL) Open Circuit	Output voltage, lower range< 1.92 - 2.21 V Output voltage, upper range> 2.85 - 3.25 V	Actuator commanded off	0.5 s Continuous	2 DCY	-- Check the Cam Adjustment Actuators --. Refer to Cam Adjustment Actuators --, CHECKING .
P11A3 Camshaft Actuator "B" Cylinder 1 Circuit/Open	Variable Valve Lift (VVL) Short To Ground	Output voltage< 1.92 - 2.21V	Actuator commanded off	0.5 s Continuous	2 DCY
P11A4 Camshaft Actuator "B" Cylinder 1 Range/Performance	Variable Valve Lift (VVL) Rationality Check Low	Actuator feedback signal voltage permanently low [-]	Modeled oil temperature< 20° C	6.0 seg Continuous	2 DCY	-- Check the Cam Adjustment Actuators --. Refer to Cam Adjustment Actuators --, CHECKING .
P11A5 Camshaft Actuator "A" Cylinder 2 Circuit/Open	Variable Valve Lift (VVL) Open Circuit	Output voltage, lower range< 1.92 - 2.21 V Output voltage, upper range> 2.85 - 3.25 V	Actuator commanded off	0.5 s Continuous	2 DCY	-- Check the Cam Adjustment Actuators --. Refer to Cam Adjustment Actuators --, CHECKING .
P11A5 Camshaft Actuator "A" Cylinder 2 Circuit/Open	Variable Valve Lift (VVL) Short To Ground	Output voltage< 1.92 - 2.21V	Actuator commanded off	0.5 s Continuous	2 DCY
P11A6 Camshaft Actuator "A" Cylinder 2 Range/Performance	Variable Valve Lift (VVL) Rationality Check Low	Actuator feedback signal voltage permanently low [-]	Modeled oil temperature< 20° C	6.0 seg Continuous	2 DCY	-- Check the Cam Adjustment Actuators --. Refer to Cam Adjustment Actuators --, CHECKING .
P11A7 Camshaft Actuator "B" Cylinder 2 Circuit/Open	Variable Valve Lift (VVL) Open Circuit	Output voltage, lower range< 1.92 - 2.21 V Output voltage, upper range> 2.85 - 3.25 V	Actuator commanded off	0.5 s Continuous	2 DCY	-- Check the Cam Adjustment Actuators --. Refer to Cam Adjustment Actuators --, CHECKING .
P11A7 Camshaft Actuator "B" Cylinder 2 Circuit/Open	Variable Valve Lift (VVL) Short To Ground	Output voltage< 1.92 - 2.21V	Actuator commanded off	0.5 s Continuous	2 DCY
P11A8 Camshaft Actuator "B" Cylinder 2 Range/Performance	Variable Valve Lift (VVL) Rationality Check Low	Actuator feedback signal voltage permanently low [-]	Modeled oil temperature< 20° C	6.0 seg Continuous	2 DCY	-- Check the Cam Adjustment Actuators --. Refer to Cam Adjustment Actuators --, CHECKING .
P11A9 Camshaft Actuator "A" Cylinder 3 Circuit/Open	Variable Valve Lift (VVL) Open Circuit	Output voltage, lower range< 1.92 - 2.21 V Output voltage, upper range> 2.85 - 3.25 V	Actuator commanded off	0.5 s Continuous	2 DCY	-- Check the Cam Adjustment Actuators --. Refer to Cam Adjustment Actuators --, CHECKING .
P11A9 Camshaft Actuator "A" Cylinder 3 Circuit/Open	Variable Valve Lift (VVL) Short To Ground	Output voltage< 1.92 - 2.21V	Actuator commanded off	0.5 s Continuous	2 DCY
P11AA Camshaft Actuator "A" Cylinder 3 Range/Performance	Variable Valve Lift (VVL) Rationality Check Low	Actuator feedback signal voltage permanently low [-]	Modeled oil temperature< 20° C	6.0 seg Continuous	2 DCY	-- Check the Cam Adjustment Actuators --. Refer to Cam Adjustment Actuators --, CHECKING .
P11AB Camshaft Actuator "B" Cylinder 3 Circuit/Open	Variable Valve Lift (VVL) Open Circuit	Output voltage, lower range< 1.92 - 2.21 V Output voltage, upper range> 2.85 - 3.25 V	Actuator commanded off	0.5 s Continuous	2 DCY	-- Check the Cam Adjustment Actuators --. Refer to Cam Adjustment Actuators --, CHECKING .
P11AB Camshaft Actuator "B" Cylinder 3 Circuit/Open	Variable Valve Lift (VVL) Short To Ground	Output voltage< 1.92 - 2.21V	Actuator commanded off	0.5 s Continuous	2 DCY
P11AC Camshaft Actuator "B" Cylinder 3 Range/Performance	Variable Valve Lift (VVL) Rationality Check Low	Actuator feedback signal voltage permanently low [-]	Modeled oil temperature< 20° C	6.0 seg Continuous	2 DCY	-- Check the Cam Adjustment Actuators --. Refer to Cam Adjustment Actuators --, CHECKING .
P11AD Camshaft Actuator "A" Cylinder 4 Circuit/Open	Variable Valve Lift (VVL) Open Circuit	Output voltage, lower range< 1.92 - 2.21 V Output voltage, upper range> 2.85 - 3.25 V	Actuator commanded off	0.5 s Continuous	2 DCY	-- Check the Cam Adjustment Actuators --. Refer to Cam Adjustment Actuators --, CHECKING .
P11AD Camshaft Actuator "A" Cylinder 4 Circuit/Open	Variable Valve Lift (VVL) Short To Ground	Output voltage< 1.92 - 2.21V	Actuator commanded off	0.5 s Continuous	2 DCY
P11AE Camshaft Actuator "A" Cylinder 4 Range/Performance	Variable Valve Lift (VVL) Rationality Check Low	Actuator feedback signal voltage permanently low [-]	Modeled oil temperature< 20° C	6.0 seg Continuous	2 DCY	-- Check the Cam Adjustment Actuators --. Refer to Cam Adjustment Actuators --, CHECKING .
P11AF Camshaft Actuator "B" Cylinder 4 Circuit/Open	Variable Valve Lift (VVL) Open Circuit	Output voltage, lower range< 1.92 - 2.21 V Output voltage, upper range> 2.85 - 3.25 V	Actuator commanded off	0.5 s Continuous	2 DCY	-- Check the Cam Adjustment Actuators --. Refer to Cam Adjustment Actuators --, CHECKING .
P11AF Camshaft Actuator "B" Cylinder 4 Circuit/Open	Variable Valve Lift (VVL) Short To Ground	Output voltage< 1.92 - 2.21V	Actuator commanded off	0.5 s Continuous	2 DCY
P11B0 Camshaft Actuator "B" Cylinder 4 Range/Performance	Variable Valve Lift (VVL) Rationality Check Low	Actuator feedback signal voltage permanently low [-]	Modeled oil temperature< 20° C	6.0 seg Continuous	2 DCY	-- Check the Cam Adjustment Actuators --. Refer to Cam Adjustment Actuators --, CHECKING .
P11BF Camshaft Actuator Outlet "A" Cylinder 1 Range/Performance	Variable Valve Lift (VVL) Short To Battery Plus	Power stage temperature > 160 - 200° C Or Output current > 4.0 - 7.0 A	Actuator commanded on	0.1 s Continuous	2 DCY	-- Check the Cam Adjustment Actuators --. Refer to Cam Adjustment Actuators --, CHECKING .
P11C0 Camshaft Actuator Outlet "B" Cylinder 1 Circuit/Open	Variable Valve Lift (VVL) Short To Battery Plus	Power stage temperature > 160 - 200° C Or Output current > 4.0 - 7.0 A	Actuator commanded on	0.1 s Continuous	2 DCY	-- Check the Cam Adjustment Actuators --. Refer to Cam Adjustment Actuators --, CHECKING .
P11C1 Camshaft Actuator Outlet "A" Cylinder 2 Range/Performance	Variable Valve Lift (VVL) Short To Battery Plus	Power stage temperature > 160 - 200° C Or Output current > 4.0 - 7.0 A	Actuator commanded on	0.1 s Continuous	2 DCY	-- Check the Cam Adjustment Actuators --. Refer to Cam Adjustment Actuators --, CHECKING .
P11C2 Camshaft Actuator Outlet "B" Cylinder 2 Circuit/Open	Variable Valve Lift (VVL) Short To Battery Plus	Power stage temperature > 160 - 200° C Or Output current > 4.0 - 7.0 A	Actuator commanded on	0.1 s Continuous	2 DCY	-- Check the Cam Adjustment Actuators --. Refer to Cam Adjustment Actuators --, CHECKING .
P11C3 Camshaft Actuator Outlet "A" Cylinder 3 Range/Performance	Variable Valve Lift (VVL) Short To Battery Plus	Power stage temperature > 160 - 200° C Or Output current > 4.0 - 7.0 A	Actuator commanded on	0.1 s Continuous	2 DCY	-- Check the Cam Adjustment Actuators --. Refer to Cam Adjustment Actuators --, CHECKING .
P11C4 Camshaft Actuator Outlet "B" Cylinder 3 Circuit/Open	Variable Valve Lift (VVL) Short To Battery Plus	Power stage temperature > 160 - 200° C Or Output current > 4.0 - 7.0 A	Actuator commanded on	0.1 s Continuous	2 DCY	-- Check the Cam Adjustment Actuators --. Refer to Cam Adjustment Actuators --, CHECKING .
P11C5 Camshaft Actuator Outlet "A" Cylinder 4 Range/Performance	Variable Valve Lift (VVL) Short To Battery Plus	Power stage temperature > 160 - 200° C Or Output current > 4.0 - 7.0 A	Actuator commanded on	0.1 s Continuous	2 DCY	-- Check the Cam Adjustment Actuators --. Refer to Cam Adjustment Actuators --, CHECKING .
P11C6 Camshaft Actuator Outlet "B" Cylinder 4 Circuit/Open	Variable Valve Lift (VVL) Short To Battery Plus	Power stage temperature > 160 - 200° C Or Output current > 4.0 - 7.0 A	Actuator commanded on	0.1 s Continuous	2 DCY	-- Check the Cam Adjustment Actuators --. Refer to Cam Adjustment Actuators --, CHECKING .
P1388 Control Module Faulty	Engine Control Module (ECM): Electronic Throttle Control Module Function Monitoring: A/D Converter	Test voltage / test pulse check failed		0.5 s Continuous	2 DCY	-- Check the Engine Control Module -J623-. Refer to appropriate repair information.
P13EA Cold Start Ignition Timing Performance Off Idle	Cold Start Monitoring Ignition Timing Monitor	Ratio between ignition angle efficiency integral and time at > 0.16 [-]	Engine part load Ignition angle efficiency set point <= 0.90 [-] Vehicle speed > 2 mph And Barometric pressure > 0.0 kPa And Catalyst heating active And Engine start temperature -10 - 80° C And Time after engine start > 2.0 s And Diff. air mass set point vs. filtered air mass set point for load dynamic detection < 99, 999.0 mg/stk For time >= 0.0 s And Diff. engine speed vs. filtered engine speed for engine speed dynamic detection < 8, 160 RPM For time >= 0.0 s	5.0 s Once / DCY	2 DCY	-- Check for any engine speed sensor or ignition coil faults and diagnose them first. If no other codes are set, replace the Engine Control Module -J623-. Refer to appropriate repair information.-- Check the Engine Speed Sensor -G28-. Refer to Engine Speed Sensor - G28-, CHECKING .-- Check the Ignition Coils with Power Output Stage --. Refer to Ignition Coils with Power Output Stage --, CHECKING .
P1545 Throttle Actuator "A" Control Motor Circuit Range/Performance	Throttle Actuator Out Of Range	Control duty cycle > 98.0%	Throttle position not at min. value Throttle adaptation not active Actuator commanded on	5.0 s Continuous	2 DCY	-- Check the Throttle Valve Control Module -GX3-. Refer to Throttle Valve Control Module - GX3-, CHECKING .
	Throttle Actuator Rationality Check	Difference between throttle position set point and throttle flap opening angle for electronic throttle control > 2.998 - 24.982° TPS	Throttle adaptation (@ initial start or after detection of throttle exchange or checksum error) not active Actuator commanded on Diff throttle position set point vs. throttle flap opening angle <= 1.999; > -1.999° TPS	5.0 s Continuous	2 DCY
P169A Loading Mode Active	Engine Control Module (ECM): Transport Mode Function Monitoring: Mode Change	Transport mode active	Vehicle speed < 3 mph Max trip mileage since initial vehicle start-up < 62.15 miles During ECM keep alive-time after ignition off Engine speed 0 RPM Production mode not active For hybrid: Drive motor off	0.01 s Continuous	1 DCY	-- Vehicle is in Transport Mode (Loading Mode). It can be turned off with a scan tool or will automatically switch off after approximately 100 km (62.15 miles) have accumulated on the vehicle. May need to perform readiness check. Refer to READINESS CODE .
P2004 Intake Manifold Runner Control Stuck Open Bank 1	Intake Manifold Runner Control (IMRC) Actuator Functional Check: Stuck Open	Signal voltage > 1.89 V For time >= 1.5 s	Actuator commanded off Time after engine start > 5.0 s	0.2 s Continuous	2 DCY	-- Check the Intake Manifold Runner Position Sensor -G336-. Refer to Intake Manifold Runner Position Sensor - G336-, CHECKING .-- Check the Intake Manifold Runner Control Valve -N316-. Refer to Intake Manifold Runner Control Valve - N316-, CHECKING .
P2006 Intake Manifold Runner Control Stuck Closed Bank 1	Intake Manifold Runner Control (IMRC) Actuator Functional Check: Stuck Close	Signal voltage < 3.10 V For time >= 1.5 s	Actuator commanded on Time after engine start > 5.0 s	0.2 s Continuous	2 DCY	-- Check the Intake Manifold Runner Position Sensor -G336-. Refer to Intake Manifold Runner Position Sensor - G336-, CHECKING .-- Check the Intake Manifold Runner Control Valve -N316-. Refer to Intake Manifold Runner Control Valve - N316-, CHECKING .
P2008 Intake Manifold Runner Control Circuit/Open Bank 1	Intake Manifold Runner Control (IMRC) Actuator Open Circuit	Output voltage lower range >= 1.92 - 2.21 V Output voltage upper range <= 2.85 - 3.25 V	Engine running Actuator commanded off	2.0 s Continuous	2 DCY	-- Check the Intake Manifold Runner Position Sensor -G336-. Refer to Intake Manifold Runner Position Sensor - G336-, CHECKING .-- Check the Intake Manifold Runner Control Valve -N316-. Refer to Intake Manifold Runner Control Valve - N316-, CHECKING .
P2009 Intake Manifold Runner Control Circuit Low Bank 1	Intake Manifold Runner Control (IMRC) Actuator Short To Ground	Output voltage (hardware values) < 1.92 - 2.21 V	Engine running Actuator commanded off	2.0 s Continuous	2 DCY	-- Check the Intake Manifold Runner Position Sensor -G336-. Refer to Intake Manifold Runner Position Sensor - G336-, CHECKING .-- Check the Intake Manifold Runner Control Valve -N316-. Refer to Intake Manifold Runner Control Valve - N316-, CHECKING .
P2010 Intake Manifold Runner Control Circuit High Bank 1	Intake Manifold Runner Control (IMRC) Actuator Short To Battery Plus	Power stage temperature > 160 - 200° C Or Output current > 4.0 - 7.0 A	Engine running Actuator commanded on	2.0 s Continuous	2 DCY	-- Check the Intake Manifold Runner Control Valve -N316-. Refer to Intake Manifold Runner Control Valve - N316-, CHECKING .-- Check the Intake Manifold Runner Position Sensor -G336-. Refer to Intake Manifold Runner Position Sensor - G336-, CHECKING .
P2014 Intake Manifold Runner Position Sensor/Switch Circuit Bank 1	Intake Manifold Runner Control (IMRC) Position Sensor Short To Ground / Open Circuit	Intake manifold runner flap position sensor voltage < 0.20 V	Engine start not active	1.9 s Continuous	2 DCY	-- Check the Intake Manifold Runner Position Sensor -G336-. Refer to Intake Manifold Runner Position Sensor - G336-, CHECKING .-- Check the Intake Manifold Runner Control Valve -N316-. Refer to Intake Manifold Runner Control Valve - N316-, CHECKING .
P2015 Intake Manifold Runner Position Sensor/Switch Circuit Range/Performance Bank 1	Intake Manifold Runner Control (IMRC) Actuator Adaptation Value Monitoring	Diff. actual value vs. substitution value @ lower mechanical thresh hold > 0.70 V Or Diff. actual value vs. substitution value @ upper mechanical thresh hold > 0.70 V Failed adaptations >= 1.0 [-]	Modeled pressure quotient < 0.75 [-] Engine running Engine speed > 640; < 1, 504 RPM ECT @ cylinder head > -30° C Intake manifold runner flap adaptation not finished	0.04 s Once per lifetime	2 DCY	-- Check the Intake Manifold Runner Position Sensor -G336-. Refer to Intake Manifold Runner Position Sensor - G336-, CHECKING .-- Check the Intake Manifold Runner Control Valve -N316-. Refer to Intake Manifold Runner Control Valve - N316-, CHECKING .
P2017 Intake Manifold Runner Position Sensor/Switch Circuit High Bank 1	Intake Manifold Runner Control (IMRC) Position Sensor Short To Battery Plus	Intake manifold runner flap position sensor voltage > 4.80 V	Engine start not active	1.9 s Continuous	2 DCY	-- Check the Intake Manifold Runner Position Sensor -G336-. Refer to Intake Manifold Runner Position Sensor - G336-, CHECKING .-- Check the Intake Manifold Runner Control Valve -N316-. Refer to Intake Manifold Runner Control Valve - N316-, CHECKING .
P2024 EVAP Fuel Vapor Temperature Sensor Circuit	Evaporative Emission (EVAP) Fuel Vapor Temperature Open Circuit	NVLD output voltage lower range >= 1.92 - 2.21 V NVLD output voltage upper <= 2.85 - 3.25 V	Case 1: Ignition on Case 2: Ignition off (during ECM keep alive-time)	0.5 s Continuous	2 DCY	-- Check the Fuel Tank Leak Detection Control Module -J909-. Refer to Fuel Tank Leak Detection Control Module - J909-, CHECKING .
P2025 EVAP Fuel Vapor Temperature Sensor Performance	Evaporative Emission (EVAP) Fuel Vapor Temperature Sensor Cross Check	Diff. between smart temperature @ engine start and ECT @ cylinder head @ engine start >= 25.5 K And Diff. between smart temperature >= 25.5 K	Engine off time >= 360.0 min IAT cross check finished ECT cross check finished Fuel level < 85.10%	1.0 s Once / DCY	2 DCY	-- Check the Fuel Tank Leak Detection Control Module -J909-. Refer to Fuel Tank Leak Detection Control Module - J909-, CHECKING .
	Evaporative Emission (EVAP) Fuel Vapor Temperature Out Of Range Low	Smart module temperature < -39° C	Engine off time >= 360.0 min ECT @ cylinder head > -23° C IAT cross check finished ECT cross check finished Fuel level < 85.10%	1.0 s Once / DCY
	Evaporative Emission (EVAP) Fuel Vapor Temperature Out Of Range High	Smart module temperature > 119° C	Ignition off Fuel level < 85.10% NVLD (EVAP-System) diagnostic mode active	300.0 s Continuous
		Smart module temperature > 119° C	Engine running	30.0 s Continuous
	Evaporative Emission (EVAP) Fuel Vapor Temperature Functional Check	Diff. time between ECM and smart module > 3.0 s	Ignition off ECM keep alive time active	3.0 s Once / DCY
		Reset counter > 3.0 [-]	Engine running Last ECM keep alive mode finished	0.1 s Once / DCY	1 DCY
	Evaporative Emission (EVAP) Fuel Vapor Temperature Signal Dynamic Check	Gradient smart temperature > 20 K/10.0 min	Ignition off Fuel level < 85.10% NVLD (EVAP-System) diagnostic mode active	300.0 s Once / DCY	2 DCY
	Evaporative Emission (EVAP) Fuel Vapor Temperature Communication with Smart Temperature Sensor	Response time > 1.0 s And Number of checks > 3.0 [-] Or Security bit incorrect And Number of checks > 3.0 [-]	Case 1: Ignition on Engine running Case 2: Ignition off (during ECM keep alive-time)	5.0 s Continuous	2 DCY
P2026 EVAP Fuel Vapor Temperature Sensor Circuit Low Voltage	Evaporative Emission (EVAP) Fuel Vapor Temperature Short To Ground	NVLD output voltage < 1.92 - 2.21 V	Case 1: Ignition on Case 2: Ignition off (during ECM keep alive-time)	0.5 s Continuous	2 DCY	-- Check the Fuel Tank Leak Detection Control Module -J909-. Refer to Fuel Tank Leak Detection Control Module - J909-, CHECKING .
P2027 EVAP Fuel Vapor Temperature Sensor Circuit High Voltage	Evaporative Emission (EVAP) Fuel Vapor Temperature Short To Battery Plus	NVLD output temperature > 160.0 - 200.0° C Or NVLD output current > 4.0 - 7.0 A	Case 1: Ignition on Case 2: Ignition off (during ECM keep alive-time)	0.5 s Continuous	2 DCY	-- Check the Fuel Tank Leak Detection Control Module -J909-. Refer to Fuel Tank Leak Detection Control Module - J909-, CHECKING .
P2067 Fuel Level Sensor "B" Circuit Low	COM: Fuel Level (FL) Sensor 2 Communication With IPC	Instrument cluster module signal: circuit low failure		0.5 s Continuous	2 DCY	-- Check the Fuel Level Sensor -G-. Refer to appropriate repair information.
P2067 Fuel Level Sensor "B" Circuit Low	COM: Fuel Level (FL) Sensor 2 Communication With IPC	Instrument cluster module signal: signal range check		0.5 s Continuous	2 DCY
P2068 Fuel Level Sensor "B" Circuit High	COM: Fuel Level (FL) Sensor 2 Communication With IPC	Instrument cluster module signal: circuit high failure		0.5 s Continuous	2 DCY	-- Check the Fuel Level Sensor -G-. Refer to appropriate repair information.
P2088 "A" Camshaft Position Actuator Control Circuit Low Bank 1	Variable Valve Timing (VVT) Intake Actuator Short To Ground	Output voltage < 1.92 - 2.21 V	Actuator commanded off	2.0 s Continuous	2 DCY	-- Check the Camshaft Position Sensor -G40-. Refer to Camshaft Position Sensor - G40-, CHECKING .-- Check the Camshaft Adjustment Valve 1 -N205-. Refer to Camshaft Adjustment Valve 1 - N205-, CHECKING .
P2089 "A" Camshaft Position Actuator Control Circuit High Bank 1	Variable Valve Timing (VVT) Intake Actuator Short To Battery Plus	Power stage temperature > 160 - 200° C Or Output current > 8.0 - 12.0 A	Actuator commanded on	2.0 s Continuous	2 DCY	-- Check the Camshaft Position Sensor -G40-. Refer to Camshaft Position Sensor - G40-, CHECKING .-- Check the Camshaft Adjustment Valve 1 -N205-. Refer to Camshaft Adjustment Valve 1 - N205-, CHECKING .
P2090 "B" Camshaft Position Actuator Control Circuit Low Bank 1	Variable Valve Timing (VVT) Exhaust Actuator Short To Ground	Output voltage< 1.92 - 2.21 V	Actuator commanded off	2.0 s Continuous	2 DCY	-- Check the Exhaust Camshaft Adjustment Valve 1 -N318-. Refer to Exhaust Camshaft Adjustment Valve 1 - N318-, CHECKING .
P2091 "B" Camshaft Position Actuator Control Circuit High Bank 1	Variable Valve Timing (VVT) Exhaust Actuator Short To Battery Plus	Power stage temperature > 160 - 200° C Or Output current> 8.0 - 12.0 A	Actuator commanded on	2.0 s Continuous	2 DCY	-- Check the Exhaust Camshaft Adjustment Valve 1 -N318-. Refer to Exhaust Camshaft Adjustment Valve 1 - N318-, CHECKING .
P2096 Post Catalyst Fuel Trim System Too Lean Bank 1	Fuel System Out Of Range Low	Adaptation value < -0.05 [-]	2nd lambda control not active Catalyst purge not active Injection mode change (DFI/MFI)not active Engine speed >= 896 RPM Counter of integrated mass for fuel in oil < 255.0 [-] Choice of: O2S rear (binary) check not active Or O2S rear (binary) check finished	0.0 s Continuous	2 DCY	-- Check the fuel pressure and delivery quantity. Refer to fuel system mechanical testing in PRELIMINARY CHECK and/or to appropriate repair information.-- Check the Oxygen Sensor 1 After Catalytic Converter -GX7-. Refer to Oxygen Sensor 1 After Catalytic Converter - GX7-, CHECKING .
P2097 Post Catalyst Fuel Trim System Too Rich Bank 1	Fuel System Out Of Range High	Adaptation value > 0.05 [-]	2nd lambda control not active Catalyst purge not active Injection mode change (DFI/MFI)not active Engine speed >= 896 RPM Counter of integrated mass for fuel in oil < 255.0 [-] Choice of: O2S rear (binary) check not active Or O2S rear (binary) check finished	0.0 s Continuous	2 DCY	-- Check the fuel pressure and delivery quantity. Refer to fuel system mechanical testing in PRELIMINARY CHECK and/or to appropriate repair information.-- Check the Oxygen Sensor 1 After Catalytic Converter -GX7-. Refer to Oxygen Sensor 1 After Catalytic Converter - GX7-, CHECKING .
P2100 Throttle Actuator "A" Control Motor Circuit/Open	Throttle Actuator Open Circuit	Electronic throttle valve driver load resistance > 200.0 kΩ	Diff. between measured and filtered throttle position <= 0.073° TPS Actuator commanded off	0.1 s Continuous	2 DCY	-- Check the Throttle Valve Control Module -GX3-. Refer to Throttle Valve Control Module - GX3-, CHECKING .
P2101 Throttle Actuator "A" Control Motor Circuit Range/Performance	Throttle Actuator Over Temperature	Electronic throttle valve driver temperature > 170.0 - 190.0° C	Actuator commanded on	0.1 s Continuous	2 DCY	-- Check the Throttle Valve Control Module -GX3-. Refer to Throttle Valve Control Module - GX3-, CHECKING .
P2103 Throttle Actuator "A" Control Motor Circuit High	Throttle Actuator Short Circuit	Electronic throttle valve driver current > 9.3 - 15.0 A	Actuator commanded on	0.1 s Continuous	2 DCY	-- Check the Throttle Valve Control Module -GX3-. Refer to Throttle Valve Control Module - GX3-, CHECKING .
P2122 Throttle/Pedal Position Sensor/Switch "D" Circuit Low	SENT: Accelerator Pedal Position (APP) Sensor 1 Circuit Low	Sensor value < 0.40 V		0.3 s Continuous	2 DCY	-- Check the Accelerator Pedal Module -GX2-. Refer to Accelerator Pedal Module - GX2-, CHECKING .
P2123 Throttle/Pedal Position Sensor/Switch "D" Circuit High	SENT: Accelerator Pedal Position (APP) Sensor 1 Circuit High	Sensor value > 4.82 V		0.3 s Continuous	2 DCY	-- Check the Accelerator Pedal Module -GX2-. Refer to Accelerator Pedal Module - GX2-, CHECKING .
P2127 Throttle/Pedal Position Sensor/Switch "E" Circuit Low	SENT: Accelerator Pedal Position (APP) Sensor 2 Circuit Low	Sensor value < 0.20 V		0.3 s Continuous	2 DCY	-- Check the Accelerator Pedal Module -GX2-. Refer to Accelerator Pedal Module - GX2-, CHECKING .
P2128 Throttle/Pedal Position Sensor/Switch "E" Circuit High	SENT: Accelerator Pedal Position (APP) Sensor 2 Circuit High	Sensor value > 2.80 V		0.3 s Continuous	2 DCY	-- Check the Accelerator Pedal Module -GX2-. Refer to Accelerator Pedal Module - GX2-, CHECKING .
P2138 Throttle/Pedal Position Sensor/Switch "D"/"E" Voltage Correlation	SENT: Accelerator Pedal Position (APP) Sensor 1 and 2 Rationality Check	Difference between signal voltage sensor 1 and sensor 2 > 0.10 - 0.12 V		0.4 s Continuous	2 DCY	-- Check the Accelerator Pedal Module -GX2-. Refer to Accelerator Pedal Module - GX2-, CHECKING .
P2177 System Too Lean Off Idle Bank 1	Fuel System Direct Fuel Injection System Too Lean @ Part Load	Adaptive value >= 28.0%	Air mass > 60.0 mg/stk ECT @ cylinder head > 20° C IAT @ manifold > -48° C AAT > -48° C Lambda set point 0.97 - 1.05 [-] Lambda control closed loop Integrated air mass >= 600.0 - 10, 000.0 g Fuel mass 15.01 - 50.0 mg/stk Engine speed1, 024 - 3, 744 RPM Low dynamic conditions: Diff. engine speed vs. averaged engine speed for engine speed dynamic detection < 60 - 130 RPM Diff. air mass vs. averaged air mass for load dynamic detection< 16.0 - 30.01 mg/stk Diff. between reference and actual fuel pressure, high side<= 2, 000.10 kPa Integrated air mass > 5.0 - 25.0 g And Evap purge valve closed Or Canister load <= 1.20 [-] Evap purge flow at max. value Or Dependence on canister purge min: Lower limit of lambda controller output not calibrated Or Upper limit of lambda controller output not calibrated And Evap purge flow at min. value	5.0 s Continuous	2 DCY	-- Check the intake and vacuum hoses visually for leaks. Check the Positive Crankcase Ventilation visually. Also make sure the oil dipstick is properly secured.-- Listen to and visually inspect the exhaust system to insure there are no leaks.-- Check the Oxygen Sensor 1 Before Catalytic Converter -GX10-. Refer to Oxygen Sensor 1 Before Catalytic Converter - GX10-, CHECKING .-- Check the Oxygen Sensor 1 After Catalytic Converter -GX7-. Refer to Oxygen Sensor 1 After Catalytic Converter - GX7-, CHECKING .-- Check the Intake Manifold Sensor -GX9-. Refer to Intake Manifold Sensor - GX9-, CHECKING .-- Check the EVAP Canister Purge Regulator Valve 1 -N80-. Refer to EVAP Canister Purge Regulator Valve 1 - N80-, CHECKING .-- Check the Fuel Injectors --. Refer to Fuel Injectors --, CHECKING .
P2178 System Too Rich Off Idle Bank 1	Fuel System Direct Fuel Injection System Too Rich @ Part Load	Adaptive value <= -28.0%	Air mass > 60.0 mg/stk ECT @ cylinder head > 20° C IAT @ manifold > -48° C AAT > -48° C Lambda set point 0.97 - 1.05 [-] Lambda control closed loop Integrated air mass >= 600.0 - 10, 000.0 g Fuel mass 15.01 - 50.0 mg/stk Engine speed1, 024 - 3, 744 RPM Low dynamic conditions: Diff. engine speed vs. averaged engine speed for engine speed dynamic detection < 60 - 130 RPM Diff. air mass vs. averaged air mass for load dynamic detection< 16.0 - 30.01 mg/stk Diff. between reference and actual fuel pressure, high side<= 2, 000.10 kPa Integrated air mass > 5.0 - 25.0 g And Evap purge valve closed Or Canister load <= 1.20 [-] Evap purge flow at max. value Or Dependence on canister purge min: Lower limit of lambda controller output not calibrated Or Upper limit of lambda controller output not calibrated And Evap purge flow at min. value	5.0 s Continuous	2 DCY	-- Check the EVAP system for possible fuel contamination. Refer to appropriate repair information.-- Check the Oxygen Sensor 1 Before Catalytic Converter -GX10-. Refer to Oxygen Sensor 1 Before Catalytic Converter - GX10-, CHECKING .-- Check the Oxygen Sensor 1 After Catalytic Converter -GX7-. Refer to Oxygen Sensor 1 After Catalytic Converter - GX7-, CHECKING .-- Check the Intake Manifold Sensor -GX9-. Refer to Intake Manifold Sensor - GX9-, CHECKING .-- Check the Fuel Injectors --. Refer to Fuel Injectors --, CHECKING .
P2181 Cooling System Performance	Engine Cooling System Rationality Check	ECT @ cylinder head < 60° C For time >= 0.0 s	Engine running Or Engine stopped And ECT @ cylinder head once after engine start > 65° C Or ECT @ radiator outlet once after engine start not calibrated ° C And AAT sensor signal valid AAT > -10° C Relative actual MAF > 5.0% ECT @ cylinder head @ first start lower limit >= -40° C ECT @ cylinder head @ first start upper limit <= 215° C Vehicle speed >= 0 mph Modeled ECT @ cylinder head > 60° C Start-stop cycles <= 255.0 [-] For time >= 15.0 s	1.0 s Once / DCY	2 DCY	-- Check cooling system visually for leaks or damaged components.-- Check the Engine Temperature Control Actuator -N493-. Refer to Engine Temperature Control Actuator - N493-, CHECKING .-- Check the Engine Coolant Temperature Sensor -G62-. Refer to Engine Coolant Temperature Sensor - G62-, CHECKING .-- Check the engine coolant thermostat. Refer to appropriate repair information.
P2181 Cooling System Performance	Engine Cooling System Rationality Check	Modeled ECT @ cylinder head > 66 - 70° C Choice of: ECT @ cylinder head < 65 - 69° C Or ECT @ radiator outlet not equipped ° C	ECT @ cylinder head @ first start >= -10° C ECT @ cylinder head @ first start <= 50 - 55° C AAT > -10° C ratio accumulated time fuel cut off vs. time since engine start <= 12.10 [%] ratio accumulated time engine load condition vs. time since engine start <= 39.80 [%] Determination engine load condition: Engine load (lower threshold)<= 2.50% Engine load (upper threshold)>= 100.0% Ratio accumulated time high speed condition <= 14.80% Determination high speed condition: Vehicle speed> 75 mph Ratio accumulated time start-stop active <= 16.0% Set point of RVC in measurement window < 99.61% Case 1: Engine speed< 8, 160 RPM Case 2: Engine speed>= 8, 160 RPM Diff. ECT@ cylinder head during measurement< 256° C For time>= 0.0 s	1.0 s Once / DCY	2 DCY
P2183 Engine Coolant Temperature Sensor 2 Circuit Range/Performance	Engine Coolant Temperature (ECT) Sensor @ Radiator Cross Check	High side: reference measuring Diff. ECT @ radiator outlet @ cold start vs. IAT @ manifold @ cold start > 25.0 K Diff. ECT @ radiator outlet @ cold start vs. ECT @ cylinder head @ cold start n.a. K Diff. ECT @ radiator outlet @ cold start vs. AAT @ cold start > 25.0 K Min. amount of faulty reference measurements to detect defective sensor 2.0 [-] Or Low side: reference measuring Diff. IAT @ manifold @ cold start vs. ECT @ radiator outlet @ cold start > 25.0 K Diff. ECT @ cylinder head @ cold start vs. ECT @ radiator outlet @ cold start n.a. K Diff. AAT @ cold start vs. ECT @ radiator outlet @ cold start> 25.0 K Min. amount of faulty reference measurements to detect 2.0 [-]	Engine off time >= 360.0 min Engine off time plausible Time after engine start <= 1, 400.0 s Depending on temperature slope @ cold start Diff. actual IAT @ manifold vs IAT @ manifold @ start of DCY < 256.0 K Diff. actual ECT @ cylinder head vs. ECT @ cylinder head @ start of DCY n.a. K Diff. actual ECT @ radiator outlet vs. ECT @ radiator outlet @ start of DCY < 256.0 K Diff. actual AAT vs. AAT @ start of DCY < 256.0 K For time>= 1.0 s Depending on mean value condition Mean value of all temperature sensors @ cold start >= -256° C Number of valid sensors >= 2.0 [-] Depending on block heater / solar radiation detection Time after engine start >= 0.5 s Vehicle speed>= 22 mph For time>= 20.0 s Diff. actual IAT @ manifold vs. min. IAT @ manifold < 5.0 K Diff. actual ECT @ cylinder head vs. min. ECT @ cylinder headn.a. K Diff. actual AAT vs. min. AAT < 4.0 K Diff. actual ECT @ radiator outlet vs. min. ECT @ radiator outlet < 1.1 K	0.1 s Once / DCY	2 DCY	-- Check the Engine Coolant Temperature Sensor On Radiator Outlet -G83-. Refer to Engine Coolant Temperature Sensor On Radiator Outlet - G83-, CHECKING .
P2184 Engine Coolant Temperature Sensor 2 Circuit Low	Engine Coolant Temperature (ECT) Sensor @ Radiator Outlet Short To Ground	Sensor voltage <= 0.30 V		0.5 s Continuous	2 DCY	-- Check the Engine Coolant Temperature Sensor On Radiator Outlet -G83-. Refer to Engine Coolant Temperature Sensor On Radiator Outlet - G83-, CHECKING .
P2185 Engine Coolant Temperature Sensor 2 Circuit High	Engine Coolant Temperature (ECT) Sensor @ Radiator Short To Battery / Open Circuit	Sensor voltage > 4.90 V	IAT @ throttle >= -33° C Time after engine start > 60.0 s	0.5 s Continuous	2 DCY	-- Check the Engine Coolant Temperature Sensor On Radiator Outlet -G83-. Refer to Engine Coolant Temperature Sensor On Radiator Outlet - G83-, CHECKING .-- Check the Engine Coolant Temperature Sensor -G62-. Refer to Engine Coolant Temperature Sensor - G62-, CHECKING .
P2187 System Too Lean at Idle Bank 1	Fuel System Direct Fuel Injection System Too Lean @ Idle	Case 1: Adaptive value >= 2.50 mg/stk Case 2: Adaptive value not calibrated kg/h	Air mass > 60.0 mg/stk ECT @ cylinder head > 20° C IAT @ manifold > -48° C AAT > -48° C Lambda set point0.97 - 1.05 [-] Lambda control closed loop Integrated air mass >= 600.0 - 10, 000.0 g Vehicle speed< 4 mph Low dynamic conditions: Diff. engine speed vs. averaged engine speed for engine speed dynamic detection < 60 - 130 RPM Diff. air mass vs. averaged air mass for load dynamic detection< 16.0 - 30.01 mg/stk Diff. between reference and actual fuel pressure, high side<= 2, 000.10 kPa Integrated air mass > 5.0 - 25.0 g And Fuel mass upper range< 0.0 - 19.01mg/stk Fuel mass lower range> 4.01 mg/stk Engine speed704 - 800 RPM Or Engine not calibrated And Evap purge valve closed Or Canister load <= 1.20 [-] Evap purge flow at max. value Or Depending on canister purge min: Lower limit of lambda controller output not calibrated Or Upper limit of lambda controller output not calibrated And Evap purge flow at min. value	5.0 s Continuous	2 DCY	-- Check the intake and vacuum hoses visually for leaks. Check the Positive Crankcase Ventilation visually. Also make sure the oil dipstick is properly secured.-- Listen to and visually inspect the exhaust system to insure there are no leaks.-- Check the Oxygen Sensor 1 Before Catalytic Converter -GX10-. Refer to Oxygen Sensor 1 Before Catalytic Converter - GX10-, CHECKING .-- Check the Oxygen Sensor 1 After Catalytic Converter -GX7-. Refer to Oxygen Sensor 1 After Catalytic Converter - GX7-, CHECKING .-- Check the Intake Manifold Sensor -GX9-. Refer to Intake Manifold Sensor - GX9-, CHECKING .-- Check the EVAP Canister Purge Regulator Valve 1 -N80-. Refer to EVAP Canister Purge Regulator Valve 1 - N80-, CHECKING .-- Check the Fuel Injectors --. Refer to Fuel Injectors --, CHECKING .
P2188 System Too Rich at Idle Bank 1	Fuel System Direct Fuel Injection System Too Rich @ Idle	Case 1: Adaptive value <= -3.01 mg/stk Case 2: Adaptive value not calibrated kg/h	Air mass > 60.0 mg/stk ECT @ cylinder head > 20° C IAT @ manifold > -48° C AAT > -48° C Lambda set point0.97 - 1.05 [-] Lambda control closed loop Oil dilution not detected Integrated air mass >= 600.0 - 10, 000.0 g Vehicle speed< 4 mph Low dynamic conditions: Diff. engine speed vs. averaged engine speed for engine speed dynamic detection < 60 - 130 RPM Diff. air mass vs. averaged air mass for load dynamic detection< 16.0 - 30.01 mg/stk Diff. between reference and actual fuel pressure, high side<= 2, 000.10 kPa Integrated air mass > 5.0 - 25.0 g And Fuel mass lower range > 4.01 mg/stk Fuel mass upper range< 0.0 - 19.01 mg/stk Engine speed704 - 800 RPM Or Engine not calibrated And Evap purge valve closed Or Canister load<= 1.20 [-] Evap purge flow at max. value Or Depending on canister purge min: Lower limit of lambda controller output not calibrated Or Upper limit of lambda controller output not calibrated And Evap purge flow at min. value	5.0 s Continuous	2 DCY	-- Check the EVAP system for possible fuel contamination. Refer to appropriate repair information.-- Check the Oxygen Sensor 1 Before Catalytic Converter -GX10-. Refer to Oxygen Sensor 1 Before Catalytic Converter - GX10-, CHECKING .-- Check the Oxygen Sensor 1 After Catalytic Converter -GX7-. Refer to Oxygen Sensor 1 After Catalytic Converter - GX7-, CHECKING .-- Check the Fuel Injectors --. Refer to Fuel Injectors --, CHECKING .
P2195 O2 Sensor Signal Biased/Stuck Lean Bank 1 Sensor 1	Oxygen Sensors (O2S) Front Rationality Check	Plausibility signal check O2S front and O2S rear: Lambda value > 1.15 [-] And O2S signal rear >= 0.91 V	O2S front ready O2S rear ready ECT @ cylinder head >= -48° C MAF > 0.0; < 2, 047.97 kg/h Catalyst purge not active Integrated air mass after end of catalyst purge 10.0 g Engine speed > 0 RPM Modeled EGT @ O2S front > -273; < 850° C Injection mode change (DFI/MFI) not active Integrated air mass > 40.0 g Dynamic lambda controller output < 3.0% Dynamic air mass < 0.05 g/rev Dynamic engine speed < 200 RPM And Second control loop active: Air mass 0.06 - 0.75 g/stk Engine speed 576 - 4, 512 RPM	67.5 s Continuous	2 DCY	-- Check the Oxygen Sensor 1 Before Catalytic Converter -GX10-. Refer to Oxygen Sensor 1 Before Catalytic Converter - GX10-, CHECKING .-- Check the Fuel Delivery Unit -GX1- / Fuel Pump Control Module -J538-. Refer to Fuel Delivery Unit -GX1- / Fuel Pump Control Module -J538-, CHECKING .-- Check the Intake Manifold Sensor -GX9-. Refer to Intake Manifold Sensor - GX9-, CHECKING .
P2196 O2 Sensor Signal Biased/Stuck Rich Bank 1 Sensor 1	Oxygen Sensors (O2S) Front Rationality Check	Plausibility signal check O2S front and O2S rear: Lambda value < 0.85 [-] And O2S signal rear <= 0.17 V	O2S front ready O2S rear ready ECT @ cylinder head >= -48° C MAF> 0.0; < 2, 047.97 kg/h Catalyst purgenot active Integrated air mass after end of catalyst purge10.0 g Engine speed> 0 RPM Modeled EGT @ O2S front> -273; < 850° C Injection mode change (DFI/MFI)not active Integrated air mass > 40.0 g Dynamic lambda controller output< 3.0% Dynamic air mass < 0.05 g/stk Dynamic engine speed< 200 RPM And Second control loop active: Air mass 0.06 - 0.75 g/stk Engine speed576 - 4, 512 RPM	67.5 s Continuous	2 DCY	-- Check the Oxygen Sensor 1 Before Catalytic Converter -GX10-. Refer to Oxygen Sensor 1 Before Catalytic Converter - GX10-, CHECKING .
P219C Cylinder 1 Air-Fuel Ratio Imbalance	Fuel System A/F Imbalance Out Of Range Low	Weighted adaptive value < -15.0%	Fuel pressure set point not calibrated kPa Modeled catalyst temperature @ start <= 900° C Lambda set value 0.97 - 1.03 [-] Catalyst heating not active Engine roughness signal valid Fuel cut off not active AAT >= -48° C Barometric pressure >= 0.0 kPa Min. injection time not reached And Choice of: Catalyst diagnosis finished Or Catalyst diagnosis not active Depending on catalyst diagnosis: Canister purge (conditions) stable Or Evap purge valve transition to closed Or Evap purge not active And O2S dynamic diagnosis finished O2S delay diagnosis finished Lambda control closed loop Catalyst purge not active Canister load <= 2.0 [-] Engine no full load Segment adaptation finished Catalyst damaging misfire not detected Emission threshold misfire not detected No gear switch for segments >= 90.0 [-] Segments after start > 0.0 [-] Time after engine start > 0.0 s Rough road not detected Min. fuel mass>= 0.0 mg/stk Intake manifold runner flap position change not active Injection mode change (DFI/MFI)not equipped Valve lift position change not active Depending on gear: 1st gear not active 2nd gear not active 3rd gear not active 4th gear active 5th gear active 6th gear active 7th gear active 8th gear active And Integrated air mass >= 0.20 - 10.0 kg Diff. engine speed vs. dynamic engine speed < 200 RPM Diff. air mass vs. dynamic air mass < 29.99 mg/stk ECT @ cylinder head 60 - 143° C Adaptation cycles <= 255.0 [-] Engine speed 1, 312 - 3, 008 RPM And Fuel mass set point lower range >= 11.0 mg/stk Fuel mass set point upper range <= 32.0 mg/stk	90.0 (does not run in FTP) s Once / DCY	2 DCY	-- Check the spark plugs visually for signs of fouling.-- Check the intake system visually for leaks (false air).-- Check the fuel pressure and delivery quantity. Refer to fuel system mechanical testing in PRELIMINARY CHECK and/or to appropriate repair information.-- Check the Fuel Injectors --. Refer to Fuel Injectors --, CHECKING .-- Check the Ignition Coils with Power Output Stage --. Refer to Ignition Coils with Power Output Stage --, CHECKING .
P219C Cylinder 1 Air-Fuel Ratio Imbalance	Fuel System A/F Imbalance Out Of Range High	Weighted adaptive value > 9.0%		90.0 (does not run in FTP) s Once / DCY	2 DCY
P219D Cylinder 2 Air-Fuel Ratio Imbalance	Fuel System A/F Imbalance Out Of Range Low	Weighted adaptive value < -15.0%	Fuel pressure set point not calibrated kPa Modeled catalyst temperature @ start <= 900° C Lambda set value 0.97 - 1.03 [-] Catalyst heating not active Engine roughness signal valid Fuel cut off not active AAT >= -48° C Barometric pressure >= 0.0 kPa Min. injection time not reached And Choice of: Catalyst diagnosis finished Or Catalyst diagnosis not active Depending on catalyst diagnosis: Canister purge (conditions) stable Or Evap purge valve transition to closed Or Evap purge not active And O2S dynamic diagnosis finished O2S delay diagnosis finished Lambda control closed loop Catalyst purge not active Canister load <= 2.0 [-] Engine no full load Segment adaptation finished Catalyst damaging misfire not detected Emission threshold misfire not detected No gear switch for segments >= 90.0 [-] Segments after start > 0.0 [-] Time after engine start > 0.0 s Rough road not detected Min. fuel mass>= 0.0 mg/stk Intake manifold runner flap position change not active Injection mode change (DFI/MFI)not equipped Valve lift position change not active Depending on gear: 1st gear not active 2nd gear not active 3rd gear not active 4th gear active 5th gear active 6th gear active 7th gear active 8th gear active And Integrated air mass >= 0.20 - 10.0 kg Diff. engine speed vs. dynamic engine speed < 200 RPM Diff. air mass vs. dynamic air mass < 29.99 mg/stk ECT @ cylinder head 60 - 143° C Adaptation cycles <= 255.0 [-] Engine speed 1, 312 - 3, 008 RPM And Fuel mass set point lower range >= 11.0 mg/stk Fuel mass set point upper range <= 32.0 mg/stk	90.0 (does not run in FTP) s Once / DCY	2 DCY	-- Check the spark plugs visually for signs of fouling.-- Check the intake system visually for leaks (false air).-- Check the fuel pressure and delivery quantity. Refer to fuel system mechanical testing in PRELIMINARY CHECK and/or to appropriate repair information.-- Check the Fuel Injectors --. Refer to Fuel Injectors --, CHECKING .-- Check the Ignition Coils with Power Output Stage --. Refer to Ignition Coils with Power Output Stage --, CHECKING .
P219D Cylinder 2 Air-Fuel Ratio Imbalance	Fuel System A/F Imbalance Out Of Range High	Weighted adaptive value > 9.0%		90.0 (does not run in FTP) s Once / DCY	2 DCY
P219E Cylinder 3 Air-Fuel Ratio Imbalance	Fuel System A/F Imbalance Out Of Range Low	Weighted adaptive value < -15.0%	Fuel pressure set point not calibrated kPa Modeled catalyst temperature @ start <= 900° C Lambda set value 0.97 - 1.03 [-] Catalyst heating not active Engine roughness signal valid Fuel cut off not active AAT >= -48° C Barometric pressure >= 0.0 kPa Min. injection time not reached And Choice of: Catalyst diagnosis finished Or Catalyst diagnosis not active Depending on catalyst diagnosis: Canister purge (conditions) stable Or Evap purge valve transition to closed Or Evap purge not active And O2S dynamic diagnosis finished O2S delay diagnosis finished Lambda control closed loop Catalyst purge not active Canister load <= 2.0 [-] Engine no full load Segment adaptation finished Catalyst damaging misfire not detected Emission threshold misfire not detected No gear switch for segments >= 90.0 [-] Segments after start > 0.0 [-] Time after engine start > 0.0 s Rough road not detected Min. fuel mass>= 0.0 mg/stk Intake manifold runner flap position change not active Injection mode change (DFI/MFI)not equipped Valve lift position change not active Depending on gear: 1st gear not active 2nd gear not active 3rd gear not active 4th gear active 5th gear active 6th gear active 7th gear active 8th gear active And Integrated air mass >= 0.20 - 10.0 kg Diff. engine speed vs. dynamic engine speed < 200 RPM Diff. air mass vs. dynamic air mass < 29.99 mg/stk ECT @ cylinder head 60 - 143° C Adaptation cycles <= 255.0 [-] Engine speed 1, 312 - 3, 008 RPM And Fuel mass set point lower range >= 11.0 mg/stk Fuel mass set point upper range <= 32.0 mg/stk	90.0 (does not run in FTP) s Once / DCY	2 DCY	-- Check the spark plugs visually for signs of fouling.-- Check the intake system visually for leaks (false air).-- Check the fuel pressure and delivery quantity. Refer to fuel system mechanical testing in PRELIMINARY CHECK and/or to appropriate repair information.-- Check the Fuel Injectors --. Refer to Fuel Injectors --, CHECKING .-- Check the Ignition Coils with Power Output Stage --. Refer to Ignition Coils with Power Output Stage --, CHECKING .
P219E Cylinder 3 Air-Fuel Ratio Imbalance	Fuel System A/F Imbalance Out Of Range High	Weighted adaptive value > 9.0%		90.0 (does not run in FTP) s Once / DCY	2 DCY
P219F Cylinder 4 Air-Fuel Ratio Imbalance	Fuel System A/F Imbalance Out Of Range Low	Weighted adaptive value < -15.0%	Fuel pressure set point not calibrated kPa Modeled catalyst temperature @ start <= 900° C Lambda set value 0.97 - 1.03 [-] Catalyst heating not active Engine roughness signal valid Fuel cut off not active AAT >= -48° C Barometric pressure >= 0.0 kPa Min. injection time not reached And Choice of: Catalyst diagnosis finished Or Catalyst diagnosis not active Depending on catalyst diagnosis: Canister purge (conditions) stable Or Evap purge valve transition to closed Or Evap purge not active And O2S dynamic diagnosis finished O2S delay diagnosis finished Lambda control closed loop Catalyst purge not active Canister load <= 2.0 [-] Engine no full load Segment adaptation finished Catalyst damaging misfire not detected Emission threshold misfire not detected No gear switch for segments >= 90.0 [-] Segments after start > 0.0 [-] Time after engine start > 0.0 s Rough road not detected Min. fuel mass>= 0.0 mg/stk Intake manifold runner flap position change not active Injection mode change (DFI/MFI)not equipped Valve lift position change not active Depending on gear: 1st gear not active 2nd gear not active 3rd gear not active 4th gear active 5th gear active 6th gear active 7th gear active 8th gear active And Integrated air mass >= 0.20 - 10.0 kg Diff. engine speed vs. dynamic engine speed < 200 RPM Diff. air mass vs. dynamic air mass < 29.99 mg/stk ECT @ cylinder head 60 - 143° C Adaptation cycles <= 255.0 [-] Engine speed 1, 312 - 3, 008 RPM And Fuel mass set point lower range >= 11.0 mg/stk Fuel mass set point upper range <= 32.0 mg/stk	90.0 (does not run in FTP) s Once / DCY	2 DCY	-- Check the spark plugs visually for signs of fouling.-- Check the intake system visually for leaks (false air).-- Check the fuel pressure and delivery quantity. Refer to fuel system mechanical testing in PRELIMINARY CHECK and/or to appropriate repair information.-- Check the Fuel Injectors --. Refer to Fuel Injectors --, CHECKING .-- Check the Ignition Coils with Power Output Stage --. Refer to Ignition Coils with Power Output Stage --, CHECKING .
P219F Cylinder 4 Air-Fuel Ratio Imbalance	Fuel System A/F Imbalance Out Of Range High	Weighted adaptive value > 9.0%		90.0 (does not run in FTP) s Once / DCY	2 DCY
P2237 O2 Sensor Positive Current Control Circuit/Open Bank 1 Sensor 1	Oxygen Sensors (O2S) Front Open Circuit Pump Voltage (VIP)	Diff. pump voltage (VIP) vs. virtual ground voltage (VG) > 1.20 V Diff. nernst voltage (VN) vs. virtual ground voltage (VG) <= 1.20 V And Choice of: Nernst voltage (VN) > 4.40 V Or Diff. pump voltage (VIP) vs. virtual ground voltage (VG) > 2.35 V Diff. pump voltage (VIP) vs. virtual ground voltage (VG) < -2.35 V Or Diff. nernst voltage (VN) vs. virtual ground voltage (VG) > 1.60 V Diff. nernst voltage (VN) vs. virtual ground voltage (VG) < -0.10 V Or Pump current > 11.5 mA Or Measurement O2S front label resistor not calibrated Ω	O2S front (linear) ready O2S ceramic temperature> 785° C For time>= 10.0s	2.3 s Continuous	2 DCY	-- Check the Oxygen Sensor 1 Before Catalytic Converter -GX10-. Refer to Oxygen Sensor 1 Before Catalytic Converter - GX10-, CHECKING .
P2243 O2 Sensor Reference Voltage Circuit/Open Bank 1 Sensor 1	Oxygen Sensors (O2S) Front Open Circuit Nernst Voltage (VN)	Diff. pump voltage (VIP) vs. virtual ground voltage (VG) <= 1.20 V Diff. nernst voltage (VN) vs. virtual ground voltage (VG) > 1.20 V And Choice of: Nernst voltage (VN) > 4.40 V Or Diff. pump voltage (VIP) vs. virtual ground voltage (VG) > 2.35 V Diff. pump voltage (VIP) vs. virtual ground voltage (VG) < -2.35 V Or Diff. nernst voltage (VN) vs. virtual ground voltage (VG) > 1.60 V Diff. nernst voltage (VN) vs. virtual ground voltage (VG) < -0.10 V Or Pump current > 11.5 mA Or Measurement O2S front label resistor not calibrated Ω	O2S front (linear) ready O2S ceramic temperature> 785° C For time>= 10.0 s	2.3 s Continuous	2 DCY	-- Check the Oxygen Sensor 1 Before Catalytic Converter -GX10-. Refer to Oxygen Sensor 1 Before Catalytic Converter - GX10-, CHECKING .
P2251 O2 Sensor Negative Current Control Circuit/Open Bank 1 Sensor 1	Oxygen Sensors (O2S) Front Open Circuit Virtual Ground (VG)	Nernst voltage (VN) > 4.40 V Or Diff. pump voltage (VIP) vs. virtual ground voltage (VG) > 2.35 V Diff. pump voltage (VIP) vs. virtual ground voltage (VG) < -2.35 V Or Diff. nernst voltage (VN) vs. virtual ground voltage (VG) > 1.60 V Diff. nernst voltage (VN) vs. virtual ground voltage (VG) < -0.10 V Or Pump current > 11.5 mA Or Measurement O2S front label resistor not calibrated Ω And Choice of: Diff. pump voltage (VIP) vs. virtual ground voltage (VG) <= 1.20 V Diff. nernst voltage (VN) vs. virtual ground voltage (VG) <= 1.20 V Or Diff. pump voltage (VIP) vs. virtual ground voltage (VG)> 1.20V Diff. nernst voltage (VN) vs. virtual ground voltage (VG)> 1.20V	O2S front (linear) ready O2S ceramic temperature> 785° C For time>= 10.0 s	2.3 s Continuous	2 DCY	-- Check the Oxygen Sensor 1 Before Catalytic Converter -GX10-. Refer to Oxygen Sensor 1 Before Catalytic Converter - GX10-, CHECKING .
P2257 AIR System Control "A" Circuit Low	Secondary Air Injection (AIR) Pump Relay Short To Ground	Output voltage 1.92 - 2.21 V	Engine running Actuator commanded off	2.0 s Continuous	2 DCY	-- Check the Secondary Air Injection Pump Relay -J299- / Secondary Air Injection Pump Motor -V101-. Refer to Secondary Air Injection Pump Relay - J299- / Secondary Air Injection Pump Motor - V101-, CHECKING .
P2258 AIR System Control "A" Circuit High	Secondary Air Injection (AIR) Pump Relay Short To Battery Plus	Actuator temperature > 160 - 200° C Or Output current > 1.0 - 2.0 A	Engine running Actuator commanded on	2.0 s Continuous	2 DCY	-- Check the Secondary Air Injection Pump Relay -J299- / Secondary Air Injection Pump Motor -V101-. Refer to Secondary Air Injection Pump Relay - J299- / Secondary Air Injection Pump Motor - V101-, CHECKING .
P2270 O2 Sensor Signal Biased/Stuck Lean Bank 1 Sensor 2	Oxygen Sensors (O2S) Rear Signal Range Check	Case 1: Max. O2S rear voltage < 0.87 V	General conditions: Vehicle speed>= 22 mph BARO >= 0.0 kPa Catalyst overheating protection not active Turbine overheating protection not active O2S rear ready O2S heater rear active O2S front ready Internal resistance O2S rear <= 700.0 Ω Time after a catalyst purge phase >= 1.0 s Integrated heat energy >= 550.0 - 700.0 kJ Or Time after engine start > 6, 553.5 s Engine speed 1, 088 - 3, 008 RPM Lambda control value < 50.0% Deviation of lambda controller output to start diagnosis < 10.0% Fast trim control ready Proportional part of secondary fuel control loop not calibrated % Coasting function not active Lambda adaptation not active Valve lift not active Counter of integrated mass for fuel in oil < 255.0 [-] And Depending on scavenging Integrated air mass after end of scavenging >= 50.0 g And Depending on lambda controller deviation Deviation of lambda controller set point And Actual value during diagnosis < 10.0% Or Deviation of lambda controller output below set point during diagnosis < 6.0 - 22.8% Or Deviation of lambda controller output over set point during diagnosis < 7.0 - 25.0% And Temperature conditions: ECT @ cylinder head > 60° C IAT @ manifold > -48° C Modeled catalyst temperature once after engine start > 510° C Modeled catalyst temperature to start diagnosis 500° C Modeled catalyst temperature during diagnosis 470 - 830° C Integrated air mass, catalyst temp. conditions fulfilled not calibrated g Diff. dynamic vs. stationary catalyst temperature to start diagnosis -100.0 - 100.0 K Diff. dynamic vs. stationary catalyst temperature to start diagnosis -150.0 - 150.0 K Modeled EGT @ O2S rear <= 900° C Air mass conditions: Air mass @ start of diagnosis 89.99 - 1, 389.0 mg/rev Air mass during diagnosis not calibrated mg/rev MAF per cylinder to start diagnosis 28.0 - 150.0 kg/h MAF per cylinder during diagnosis not calibrated kg/h Load conditions: Air mass set point not calibrated mg/rev Engine load not calibrated % Accelerator pedal valuenot calibrated % For timenot calibrated s And Low dynamic conditions Dynamic engine speed< 50 RPM Dynamic air mass < 29.99 mg/rev Dynamic lambda controller output< 20.0% Integrated air mass after dynamic conditions are fulfilled > 20.0 g Evap purge conditions: Case 1: Evap purge valve not calibrated Case 2: Canister load calculation not calibrated Evap purge flow not calibrated Case 3: Canister load not calibrated [-] Evap purge flow not calibrated Close the gap conditions: O2S rear voltage @ diagnosis start >= 0.55 V Integrated air mass to start diagnosis >= 0.0 g O2S front dynamic diagnosis separate not active	0.0 s Once / DCY	2 DCY	-- Check the Oxygen Sensor 1 After Catalytic Converter -GX7-. Refer to Oxygen Sensor 1 After Catalytic Converter - GX7-, CHECKING .
P2271 O2 Sensor Signal Biased/Stuck Rich Bank 1 Sensor 2	Oxygen Sensors (O2S) Rear Close The Gap Conditions: Signal Range Check	Case 1: Min. O2S rear voltage > 0.25 V	General conditions: Vehicle speed>= 22 mph BARO >= 0.0 kPa Catalyst overheating protection not active Turbine overheating protection not active O2S rear ready O2S heater rear active O2S front ready Internal resistance O2S rear <= 700.0 Ω Time after a catalyst purge phase >= 1.0 s Integrated heat energy >= 550.0 - 700.0 kJ Or Time after engine start > 6, 553.5 s Engine speed 1, 088 - 3, 008 RPM Lambda control value < 50.0% Deviation of lambda controller output to start diagnosis < 10.0% Fast trim control ready Proportional part of secondary fuel control loop not calibrated % Coasting function not active Lambda adaptation not active Valve lift not active Counter of integrated mass for fuel in oil < 255.0 [-] And Depending on scavenging Integrated air mass after end of scavenging >= 50.0 g And Depending on lambda controller deviation Deviation of lambda controller set point And Actual value during diagnosis < 10.0% Or Deviation of lambda controller output below set point during diagnosis < 6.0 - 22.8% Or Deviation of lambda controller output over set point during diagnosis < 7.0 - 25.0% And Temperature conditions: ECT @ cylinder head > 60° C IAT @ manifold > -48° C Modeled catalyst temperature once after engine start > 510° C Modeled catalyst temperature to start diagnosis 500° C Modeled catalyst temperature during diagnosis 470 - 830° C Integrated air mass, catalyst temp. conditions fulfilled not calibrated g Diff. dynamic vs. stationary catalyst temperature to start diagnosis -100.0 - 100.0 K Diff. dynamic vs. stationary catalyst temperature to start diagnosis -150.0 - 150.0 K Modeled EGT @ O2S rear <= 900° C Air mass conditions: Air mass @ start of diagnosis 89.99 - 1, 389.0 mg/rev Air mass during diagnosis not calibrated mg/rev MAF per cylinder to start diagnosis 28.0 - 150.0 kg/h MAF per cylinder during diagnosis not calibrated kg/h Load conditions: Air mass set point not calibrated mg/rev Engine load not calibrated % Accelerator pedal valuenot calibrated % For timenot calibrated s And Low dynamic conditions Dynamic engine speed< 50 RPM Dynamic air mass < 29.99 mg/rev Dynamic lambda controller output< 20.0% Integrated air mass after dynamic conditions are fulfilled > 20.0 g Evap purge conditions: Case 1: Evap purge valve not calibrated Case 2: Canister load calculation not calibrated Evap purge flow not calibrated Case 3: Canister load not calibrated [-] Evap purge flow not calibrated Close the gap conditions: O2S rear voltage @ diagnosis start >= 0.55 V Integrated air mass to start diagnosis >= 0.0 g O2S front dynamic diagnosis separate not active	0.0 s Once / DCY	2 DCY	-- Check the Oxygen Sensor 1 After Catalytic Converter -GX7-. Refer to Oxygen Sensor 1 After Catalytic Converter - GX7-, CHECKING .
P2279 MAP/MAF - Throttle Position Correlation	Intake Air (IA) System Rationality Check	Throttle opening area correction included controller and adaptation > 60.0% Lambda controller included correction and adaptation -30.0 - 30.0% Lambda controller active	Intake manifold modeled adaption active (By throttle opening area) Throttle position 0.0 - 100.003° TPS Engine speed 576 - 3, 008 RPM Pressure quotient @ throttle 0.22 - 0.60 [-] Fast throttle adaptation finished MAP Gradient -200.0 - 200.0 kPa/s Fuel cut off not active Time after engine start > 5.0 s Turbocharger boost pressure < 135.0 kPa BARO 73.0 - 107.50 kPa	5.0 s Continuous	2 DCY	-- Check visually for air leaks between intake and throttle body, oil fill cap not tight or oil dipstick not seated in tube.-- Also visually inspect any engine gaskets that can cause additional air to enter the crankcase can set this fault as the PCV system is not metered. If a vacuum leak or crankcase gasket sealing is at cause, the idle may be rough or unstable.-- Check the Intake Manifold Sensor -GX9-. Refer to Intake Manifold Sensor - GX9-, CHECKING .-- Check the Throttle Valve Control Module -GX3-. Refer to Throttle Valve Control Module - GX3-, CHECKING .-- Check the EVAP Canister Purge Regulator Valve 1 -N80-. Refer to EVAP Canister Purge Regulator Valve 1 - N80-, CHECKING .
P2279 MAP/MAF - Throttle Position Correlation	Intake Air (IA) System Rationality Check	Ratio adapted turbocharger boost pressure and actual turbocharger boost pressure > 35.0% Lambda controller included correction and adaptation -50.0 - 50.0% Lambda controller active	Intake manifold modeled adaptation active (By turbocharger boost pressure) Throttle position > 4.50° TPS Engine speed 1, 216 - 6, 000 RPM Pressure quotient @ throttle 0.63 - 0.90 [-] Engine running Fast throttle adaptation finished MAP gradient -200.0 - 200.0 kPa/s Fuel cut off not active Time after engine start > 5.0 s Boost pressure < 135.0 kPa BARO 73.0 - 107.50 kPa	5.0 s Continuous	2 DCY
P2300 Ignition Coil "A" Primary Control Circuit Low	Ignition Coils Short To Ground	Output current in on state > 50.0 - 100.0 mA	Engine speed > 512 RPM ECT @ cylinder head > -30° C Engine stop not active	1.0 s Continuous	2 DCY	-- Check the Ignition Coils with Power Output Stage --. Refer to Ignition Coils with Power Output Stage --, CHECKING .
P2301 Ignition Coil "A" Primary Control Circuit High	Ignition Coils Short To Battery Plus	Diagnosis by inactive low side switch in ATIC: Output voltage in off state > 4.95 - 5.285 V	Engine speed > 512 RPM Engine stop not active Actuator commanded off	1.0 s Continuous	2 DCY	-- Check the Ignition Coils with Power Output Stage --. Refer to Ignition Coils with Power Output Stage --, CHECKING .
P2301 Ignition Coil "A" Primary Control Circuit High	Ignition Coils Short To Battery Plus	Diagnosis by active low side: switch in ATIC: Output temperature from ATIC in on state > 160.0 - 200.0° C Or Output current in on state > 100.0 - 180.0 mA	Engine speed > 512 RPM Engine stop not active Actuator commanded on	1.0 s Continuous	2 DCY
P2302 Ignition Coil "A" Secondary Circuit	Ignition Coils Open Circuit	Output voltage in off state, lower range >= 1.92 - 2.21 V Output voltage in off state, <= 2.85 - 3.25 V	Engine speed > 512 RPM ECT @ cylinder head > -30° C Engine stop not active	1.0 s Continuous	2 DCY	-- Check the Ignition Coils with Power Output Stage --. Refer to Ignition Coils with Power Output Stage --, CHECKING .
P2303 Ignition Coil "B" Primary Control Circuit Low	Ignition Coils Short To Ground	Output current in on state > 50.0 - 100.0 mA	Engine speed > 512 RPM ECT @ cylinder head > -30° C Engine stop not active	1.0 s Continuous	2 DCY	-- Check the Ignition Coils with Power Output Stage --. Refer to Ignition Coils with Power Output Stage --, CHECKING .
P2304 Ignition Coil "B" Primary Control Circuit High	Ignition Coils Short To Battery Plus	Diagnosis by inactive low side switch in ATIC: Output voltage in off state > 4.95 - 5.285 V	Engine speed > 512 RPM Engine stop not active Actuator commanded off	1.0 s Continuous	2 DCY	-- Check the Ignition Coils with Power Output Stage --. Refer to Ignition Coils with Power Output Stage --, CHECKING .
P2304 Ignition Coil "B" Primary Control Circuit High	Ignition Coils Short To Battery Plus	Diagnosis by active low side: switch in ATIC: Output temperature from ATIC in on state > 160.0 - 200.0° C Or Output current in on state > 100.0 - 180.0 mA	Engine speed > 512 RPM Engine stop not active Actuator commanded on	1.0 s Continuous	2 DCY
P2305 Ignition Coil "B" Secondary Circuit	Ignition Coils Open Circuit	Output voltage in off state, lower range >= 1.92 - 2.21 V Output voltage in off state, <= 2.85 - 3.25 V	Engine speed > 512 RPM ECT @ cylinder head > -30° C Engine stop not active	1.0 s Continuous	2 DCY	-- Check the Ignition Coils with Power Output Stage --. Refer to Ignition Coils with Power Output Stage --, CHECKING .
P2306 Ignition Coil "C" Primary Control Circuit Low	Ignition Coils Short To Ground	Output current in on state > 50.0 - 100.0 mA	Engine speed > 512 RPM ECT @ cylinder head > -30° C Engine stop not active	1.0 s Continuous	2 DCY	-- Check the Ignition Coils with Power Output Stage --. Refer to Ignition Coils with Power Output Stage --, CHECKING .
P2307 Ignition Coil "C" Primary Control Circuit High	Ignition Coils Short To Battery Plus	Diagnosis by inactive low side switch in ATIC: Output voltage in off state > 4.95 - 5.285 V	Engine speed > 512 RPM Engine stop not active Actuator commanded off	1.0 s Continuous	2 DCY	-- Check the Ignition Coils with Power Output Stage --. Refer to Ignition Coils with Power Output Stage --, CHECKING .
P2307 Ignition Coil "C" Primary Control Circuit High	Ignition Coils Short To Battery Plus	Diagnosis by active low side: switch in ATIC: Output temperature from ATIC in on state > 160.0 - 200.0° C Or Output current in on state > 100.0 - 180.0 mA	Engine speed > 512 RPM Engine stop not active Actuator commanded on	1.0 s Continuous	2 DCY
P2308 Ignition Coil "C" Secondary Circuit	Ignition Coils Open Circuit	Output voltage in off state, lower range >= 1.92 - 2.21 V Output voltage in off state, <= 2.85 - 3.25 V	Engine speed > 512 RPM ECT @ cylinder head > -30° C Engine stop not active	1.0 s Continuous	2 DCY	-- Check the Ignition Coils with Power Output Stage --. Refer to Ignition Coils with Power Output Stage --, CHECKING .
P2309 Ignition Coil "D" Primary Control Circuit Low	Ignition Coils Short To Ground	Output current in on state > 50.0 - 100.0 mA	Engine speed > 512 RPM ECT @ cylinder head > -30° C Engine stop not active	1.0 s Continuous	2 DCY	-- Check the Ignition Coils with Power Output Stage --. Refer to Ignition Coils with Power Output Stage --, CHECKING .
P2310 Ignition Coil "D" Primary Control Circuit High	Ignition Coils Short To Battery Plus	Diagnosis by inactive low side switch in ATIC: Output voltage in off state > 4.95 - 5.285 V	Engine speed > 512 RPM Engine stop not active Actuator commanded off	1.0 s Continuous	2 DCY	-- Check the Ignition Coils with Power Output Stage --. Refer to Ignition Coils with Power Output Stage --, CHECKING .
P2310 Ignition Coil "D" Primary Control Circuit High	Ignition Coils Short To Battery Plus	Diagnosis by active low side: switch in ATIC: Output temperature from ATIC in on state > 160.0 - 200.0° C Or Output current in on state > 100.0 - 180.0 mA	Engine speed > 512 RPM Engine stop not active Actuator commanded on	1.0 s Continuous	2 DCY
P2311 Ignition Coil "D" Secondary Circuit	Ignition Coils Open Circuit	Output voltage in off state, lower range >= 1.92 - 2.21 V Output voltage in off state, <= 2.85 - 3.25 V	Engine speed > 512 RPM ECT @ cylinder head > -30° C Engine stop not active	1.0 s Continuous	2 DCY	-- Check the Ignition Coils with Power Output Stage --. Refer to Ignition Coils with Power Output Stage --, CHECKING .
P230A Cylinder 1 Air-Fuel Ratio Imbalance - Adjustment At Limit During Balance	Fuel System A/F Imbalance: Rationality Check	Cylinder misfire counter> 10.0 [-]	Fuel pressure set pointnot calibrated kPa Modeled catalyst temperature @ start <= 900° C Lambda set value 0.97 - 1.03 [-] Catalyst heating not active Engine roughness signal valid Fuel cut offnot active AAT >= -48° C Barometric pressure>= 0.0 kPa And Min. injection timenot reached And Choice of: Catalyst diagnosis finished Or Catalyst diagnosis not active Depending on catalyst diagnosis: Canister purge (conditions) stable Or Evap purge valvetransition to closed Or Evap purgenot active And O2S dynamic diagnosisfinished O2S delay diagnosisfinished Lambda control closed loop Catalyst purgenot active Canister load <= 2.0 [-] Engine no full load Segment adaptationfinished Catalyst damaging misfirenot detected Emission threshold misfirenot detected No gear switch for segments >= 90.0 [-] Segments after start> 0.0 [-] Time after engine start > 0.0 s Rough road not detected And Min. fuel mass>= 0.0 mg/stk Intake manifold runner flap position change not active Injection mode change (DFI/MFI)not equipped Valve lift position change not active And Depending on gear 1st gearnot active 2nd gear not active 3rd gear not active 4th gearactive 5th gearactive 6th gearactive 7th gearactive 8th gearactive And Integrated air mass >= 0.20 - 10.0 kg Diff. engine speed vs. dynamic engine speed < 200 RPM Diff. air mass vs. dynamic air mass < 29.99 mg/stk ECT @ cylinder head 60 - 143° C Adaptation cycles<= 255.0 [-] Engine speed 1, 312 - 3, 008 RPM And Fuel mass set point lower range>= 11.0 mg/stk Fuel mass set point upper range<= 32.0 mg/stk	90.0 (does not run in FTP) s Once / DCY	2 DCY	-- Check the Fuel Injectors --. Refer to Fuel Injectors --, CHECKING .-- Check the Oxygen Sensor 1 Before Catalytic Converter -GX10-. Refer to Oxygen Sensor 1 Before Catalytic Converter - GX10-, CHECKING .-- Check the Oxygen Sensor 1 After Catalytic Converter -GX7-. Refer to Oxygen Sensor 1 After Catalytic Converter - GX7-, CHECKING
P230B Cylinder 2 Air-Fuel Ratio Imbalance - Adjustment At Limit During Balance	Fuel System A/F Imbalance: Rationality Check	Cylinder misfire counter> 10.0 [-]	Fuel pressure set pointnot calibrated kPa Modeled catalyst temperature @ start <= 900° C Lambda set value 0.97 - 1.03 [-] Catalyst heating not active Engine roughness signal valid Fuel cut offnot active AAT >= -48° C Barometric pressure>= 0.0 kPa And Min. injection timenot reached And Choice of: Catalyst diagnosis finished Or Catalyst diagnosis not active Depending on catalyst diagnosis: Canister purge (conditions) stable Or Evap purge valvetransition to closed Or Evap purgenot active And O2S dynamic diagnosisfinished O2S delay diagnosisfinished Lambda control closed loop Catalyst purgenot active Canister load <= 2.0 [-] Engine no full load Segment adaptationfinished Catalyst damaging misfirenot detected Emission threshold misfirenot detected No gear switch for segments >= 90.0 [-] Segments after start> 0.0 [-] Time after engine start > 0.0 s Rough road not detected And Min. fuel mass>= 0.0 mg/stk Intake manifold runner flap position change not active Injection mode change (DFI/MFI)not equipped Valve lift position change not active And Depending on gear 1st gearnot active 2nd gear not active 3rd gear not active 4th gearactive 5th gearactive 6th gearactive 7th gearactive 8th gearactive And Integrated air mass >= 0.20 - 10.0 kg Diff. engine speed vs. dynamic engine speed < 200 RPM Diff. air mass vs. dynamic air mass < 29.99 mg/stk ECT @ cylinder head 60 - 143° C Adaptation cycles<= 255.0 [-] Engine speed 1, 312 - 3, 008 RPM And Fuel mass set point lower range>= 11.0 mg/stk Fuel mass set point upper range<= 32.0 mg/stk	90.0 (does not run in FTP) s Once / DCY	2 DCY	-- Check the Fuel Injectors --. Refer to Fuel Injectors --, CHECKING .-- Check the Oxygen Sensor 1 Before Catalytic Converter -GX10-. Refer to Oxygen Sensor 1 Before Catalytic Converter - GX10-, CHECKING .-- Check the Oxygen Sensor 1 After Catalytic Converter -GX7-. Refer to Oxygen Sensor 1 After Catalytic Converter - GX7-, CHECKING .
P230C Cylinder 3 Air-Fuel Ratio Imbalance - Adjustment At Limit During Balance	Fuel System A/F Imbalance: Rationality Check	Cylinder misfire counter> 10.0 [-]	Fuel pressure set pointnot calibrated kPa Modeled catalyst temperature @ start <= 900° C Lambda set value 0.97 - 1.03 [-] Catalyst heating not active Engine roughness signal valid Fuel cut offnot active AAT >= -48° C Barometric pressure>= 0.0 kPa And Min. injection timenot reached And Choice of: Catalyst diagnosis finished Or Catalyst diagnosis not active Depending on catalyst diagnosis: Canister purge (conditions) stable Or Evap purge valvetransition to closed Or Evap purgenot active And O2S dynamic diagnosisfinished O2S delay diagnosisfinished Lambda control closed loop Catalyst purgenot active Canister load <= 2.0 [-] Engine no full load Segment adaptationfinished Catalyst damaging misfirenot detected Emission threshold misfirenot detected No gear switch for segments >= 90.0 [-] Segments after start> 0.0 [-] Time after engine start > 0.0 s Rough road not detected And Min. fuel mass>= 0.0 mg/stk Intake manifold runner flap position change not active Injection mode change (DFI/MFI)not equipped Valve lift position change not active And Depending on gear 1st gearnot active 2nd gear not active 3rd gear not active 4th gearactive 5th gearactive 6th gearactive 7th gearactive 8th gearactive And Integrated air mass >= 0.20 - 10.0 kg Diff. engine speed vs. dynamic engine speed < 200 RPM Diff. air mass vs. dynamic air mass < 29.99 mg/stk ECT @ cylinder head 60 - 143° C Adaptation cycles<= 255.0 [-] Engine speed 1, 312 - 3, 008 RPM And Fuel mass set point lower range>= 11.0 mg/stk Fuel mass set point upper range<= 32.0 mg/stk	90.0 (does not run in FTP) s Once / DCY	2 DCY	-- Check the Fuel Injectors --. Refer to Fuel Injectors --, CHECKING .-- Check the Oxygen Sensor 1 Before Catalytic Converter -GX10-. Refer to Oxygen Sensor 1 Before Catalytic Converter - GX10-, CHECKING .-- Check the Oxygen Sensor 1 After Catalytic Converter -GX7-. Refer to Oxygen Sensor 1 After Catalytic Converter - GX7-, CHECKING ..
P230D Cylinder 4 Air-Fuel Ratio Imbalance - Adjustment At Limit During Balance	Fuel System A/F Imbalance: Rationality Check	Cylinder misfire counter> 10.0 [-]	Fuel pressure set pointnot calibrated kPa Modeled catalyst temperature @ start <= 900° C Lambda set value 0.97 - 1.03 [-] Catalyst heating not active Engine roughness signal valid Fuel cut offnot active AAT >= -48° C Barometric pressure>= 0.0 kPa And Min. injection timenot reached And Choice of: Catalyst diagnosis finished Or Catalyst diagnosis not active Depending on catalyst diagnosis: Canister purge (conditions) stable Or Evap purge valvetransition to closed Or Evap purgenot active And O2S dynamic diagnosisfinished O2S delay diagnosisfinished Lambda control closed loop Catalyst purgenot active Canister load <= 2.0 [-] Engine no full load Segment adaptationfinished Catalyst damaging misfirenot detected Emission threshold misfirenot detected No gear switch for segments >= 90.0 [-] Segments after start> 0.0 [-] Time after engine start > 0.0 s Rough road not detected And Min. fuel mass>= 0.0 mg/stk Intake manifold runner flap position change not active Injection mode change (DFI/MFI)not equipped Valve lift position change not active And Depending on gear 1st gearnot active 2nd gear not active 3rd gear not active 4th gearactive 5th gearactive 6th gearactive 7th gearactive 8th gearactive And Integrated air mass >= 0.20 - 10.0 kg Diff. engine speed vs. dynamic engine speed < 200 RPM Diff. air mass vs. dynamic air mass < 29.99 mg/stk ECT @ cylinder head 60 - 143° C Adaptation cycles<= 255.0 [-] Engine speed 1, 312 - 3, 008 RPM And Fuel mass set point lower range>= 11.0 mg/stk Fuel mass set point upper range<= 32.0 mg/stk	90.0 (does not run in FTP) s Once / DCY	2 DCY	-- Check the Fuel Injectors --. Refer to Fuel Injectors --, CHECKING -- Check the Oxygen Sensor 1 Before Catalytic Converter -GX10-. Refer to Oxygen Sensor 1 Before Catalytic Converter - GX10-, CHECKING .-- Check the Oxygen Sensor 1 After Catalytic Converter -GX7-. Refer to Oxygen Sensor 1 After Catalytic Converter - GX7-, CHECKING ..
P2414 O2 Sensor Exhaust Sample Error Bank 1 Sensor 1	Oxygen Sensors (O2S) Front Rationality Check	Pump current correction (nernst-cell) > 1.2 mA	O2S front ready Fuel cut off not active Injection mode change (DFI/MFI) not active Depending on engine state: Engine part load Or Engine full load Or Engine idle For time >= 3.0 s	10.0 s Continuous	2 DCY	-- Check the Oxygen Sensor 1 Before Catalytic Converter -GX10-. Refer to Oxygen Sensor 1 Before Catalytic Converter - GX10-, CHECKING .
P2431 AIR System Air Flow/Pressure Sensor Circuit Range/Performance Bank 1	Secondary Air Injection (AIR) Pressure Sensor Rationality Check	Difference between AIR pressure and barometric pressure > 6.0 kPa And Difference between AIR pressure and intake manifold pressure > 6.0 kPa	Engine stop For time > 0.0 s	0.1 s Multiple	2 DCY	-- Check the Secondary Air System -GX24-. Refer to Secondary Air Injection Sensor 1 - G609-, CHECKING .
P2432 AIR System Air Flow/Pressure Sensor Circuit Low Bank 1	Secondary Air Injection (AIR) Pressure Sensor Out Of Range Low	Sensor voltage < 0.50 V		0.1 s Continuous	2 DCY	-- Check the Secondary Air System -GX24-. Refer to Secondary Air Injection Sensor 1 - G609-, CHECKING .
P2433 AIR System Air Flow/Pressure Sensor Circuit High Bank 1	Secondary Air Injection (AIR) Pressure Sensor Out Of Range High	Sensor voltage > 4.50 V		0.1 s Continuous	2 DCY	-- Check the Secondary Air System -GX24-. Refer to Secondary Air Injection Sensor 1 - G609-, CHECKING .
P2440 AIR System Switching Valve Stuck Open Bank 1	Secondary Air Injection (AIR) Valve Functional Check	Ratio relative pressure phase 1 and relative pressure phase 2 > 1.34 [-]	General: AIR pump active Catalyst heating active AIR active MAF 140.0 kg/h ECT @ cylinder head >= -10; < 115° C IAT @ manifold >= -10; < 100° C Modeled catalyst temperature < 900° C Relative barometric pressure > 0.73 [-] And Diff. BARO vs. MAP n.a. kPa Or Engine n.a.	0.1 s Once / DCY	2 DCY	-- Check the Secondary Air Injection Solenoid Valve -N112-. Refer to Secondary Air Injection Solenoid Valve - N112-, CHECKING .-- Check the Secondary Air Injection Pump Relay -J299- / Secondary Air Injection Pump Motor -V101-. Refer to Secondary Air Injection Pump Relay - J299- / Secondary Air Injection Pump Motor - V101-, CHECKING .
P2556 Engine Coolant Level Sensor/Switch Circuit	Engine Cooling System: Bypass Valve Signal Check	Sensor signal failure		0.5 s Continuous	2 DCY	-- Check the Engine Temperature Control Actuator -N493-. Refer to Engine Temperature Control Actuator - N493-, CHECKING .
P2556 Engine Coolant Level Sensor/Switch Circuit	Engine Cooling System: Bypass Valve Communication Check	Communication signal failure		0.5 s Continuous	2 DCY
P2557 Engine Coolant Level Sensor/Switch Circuit Range/Performance	Engine Cooling System: Bypass Valve Checksum Verification	Checksum signal failure		0.5 s Continuous	2 DCY	-- Check the Engine Temperature Control Actuator -N493-. Refer to Engine Temperature Control Actuator - N493-, CHECKING .
P2564 Turbocharger Boost Control Position Sensor "A" Circuit Low	Turbocharger (TC) Position Sensor Circuit Low	Turbocharger boost control position sensor voltage < 0.20 V		0.5 s Continuous	2 DCY	-- Check the Charge Air Pressure Actuator -V465-. Refer to Charge Air Pressure Actuator - V465- / Charge Air Pressure Actuator Position Sensor - G581-, CHECKING ..-- Check the Turbocharger Recirculation Valve -N249-. Refer to Turbocharger Recirculation Valve - N249-, CHECKING ..
P2565 Turbocharger Boost Control Position Sensor "A" Circuit High	Turbocharger (TC) Position Sensor Circuit High	Turbocharger boost control position sensor voltage > 4.80 V		0.5 s Continuous	2 DCY	-- Check the Charge Pressure Actuator -V465- / Charge Pressure Actuator Position Sensor -G581-. Refer to Charge Air Pressure Actuator - V465- / Charge Air Pressure Actuator Position Sensor - G581-, CHECKING .-- Check the Turbocharger Recirculation Valve -N249-. Refer to Turbocharger Recirculation Valve - N249-, CHECKING .
P2610 ECM/PCM Engine Off Timer Performance	Engine Off Time Rationality Check	Difference between engine-off-time and ECM keep alive-time > 12.0 s	Monitor entry conditions: ECM keep alive-time active Delay time >= 1.0 s Last ECM activation time >= 2.0 s Time after last engine stop< 48.0 h Case 1: For time (after entry conditions fulfilled) >= 65.0 s Case 2: For time (after entry conditions fulfilled) < 65.0 s Ignition keytransition off to on	10.0 ms Once / DCY	2 DCY	-- Check ALL power and grounds to the ECM. The ECM must have a power supply when the key is off to run the timer and system checks. If OK, replace the Engine Control Module -J623-. Refer to appropriate repair information.
	Engine Off Time Rationality Check	Difference between ECM keep alive-time and engine-off-time>= 12.0 s	Time after last ignition off < 24.0 h Time after ECM wake up < 2.0 s SPI initialization finished	10.0 ms Once / DCY
	Engine Off Time ECM Internal Timer Check	ECM internal timer failure Or ECM internal timer signalnot calibrated ECM internal timer not calibrated Time after last engine stop not calibrated h	SPI initialization finished	1.3 s Continuous
P2635 Fuel Pump Control Module Performance	Fuel Pump Control Module (FPCM) Signal Range Check	Phase current > 15.0; < 17.0 A		6.1 s Continuous	2 DCY	-- Check the Fuel Delivery Unit -GX1- / Fuel Pump Control Module -J538-. Refer to Fuel Delivery Unit -GX1- / Fuel Pump Control Module -J538-, CHECKING .-- Replace the Engine Control Module -J623-. Refer to appropriate repair information.
	Fuel Pump Control Module (FPCM) Function Check: Permanent Operation Supply Voltage	FPCM - power supply active And ECM not active		3.7 s Continuous
	Fuel Pump Control Module (FPCM) Locked Pump	Phase current >= 17.0; < 25.0 [-]		6.3 s Continuous
P2681 Engine Coolant Bypass Valve "A" Control Circuit/Open	Engine Cooling System: Bypass Valve Open Circuit	Load resistance > 200.0 kΩ	Actuator commanded off	1.3 s Continuous	2 DCY	-- Check the Engine Temperature Control Actuator -N493-. Refer to Engine Temperature Control Actuator - N493-, CHECKING ..
P2682 Engine Coolant Bypass Valve "A" Control Circuit Low	Engine Cooling System: Bypass Valve Short To Ground	High side current output 1 > 9.3 - 15.0 A	Actuator commanded on Rotary valve direction forward	0.3 s Continuous	2 DCY	-- Check the Engine Temperature Control Actuator -N493-. Refer to Engine Temperature Control Actuator - N493-, CHECKING .
P2682 Engine Coolant Bypass Valve "A" Control Circuit Low	Engine Cooling System: Bypass Valve Short To Ground	High side current output 2 > 9.3 - 15.0 A	Actuator commanded on Rotary valve direction reversed	0.3 s Continuous	2 DCY
P2683 Engine Coolant Bypass Valve "A" Control Circuit High	Engine Cooling System: Bypass Valve Short To Battery Plus	Low side current output 1 > 9.3 - 15.0 A	Actuator commanded off	0.3 s Continuous	2 DCY	-- Check the Engine Temperature Control Actuator -N493-. Refer to Engine Temperature Control Actuator - N493-, CHECKING .
P2683 Engine Coolant Bypass Valve "A" Control Circuit High	Engine Cooling System: Bypass Valve Short To Battery Plus	Low side current output 2 > 9.3 - 15.0 A	Actuator commanded off	0.3 s Continuous	2 DCY
P334A Charge Pressure Actuator Electrical Error	Turbocharger (TC) Boost Pressure Control Short Circuit	Bypass valve driver current > 9.3 - 15.0 A	Boost pressure control active	0.4 s Continuous	2 DCY	-- Check the Charge Pressure Actuator -V465- / Charge Pressure Actuator Position Sensor -G581-. Refer to Charge Air Pressure Actuator - V465- / Charge Air Pressure Actuator Position Sensor - G581-, CHECKING .-- Check the Turbocharger Recirculation Valve -N249-. Refer to Turbocharger Recirculation Valve - N249-, CHECKING .
U0001 High Speed CAN Communication Bus	CAN: Powertrain Reading Back Sent Message	Message no feedback	Time after ignition on 0.5 s	0.5 s Continuous	2 DCY	-- Check the CAN-Bus terminal resistance. Refer to CAN-BUS TERMINAL RESISTANCE, CHECKING .
U0002 High Speed CAN Communication Bus Performance	CAN: Powertrain Communication Check Powertrain	Global time out receiving no message	Time after ignition on 0.5 s	0.5 s Continuous	2 DCY	-- Check the CAN-Bus terminal resistance. Refer to CAN-BUS TERMINAL RESISTANCE, CHECKING .
U0101 Lost Communication with TCM	COM: Transmission Control Module (TCM) Communication With TCM	Received message no message	Time after ignition on 0.5 s	1.0 s Continuous	2 DCY	-- Check the CAN-Bus terminal resistance. Refer to CAN-BUS TERMINAL RESISTANCE, CHECKING .
U0121 Lost Communication With Anti-Lock Brake System (ABS) Control Module	COM: Brake System Control Module (BSCM) Communication With BSCM	Received message no message	Time after ignition on 0.5 s	0.5 s Continuous	2 DCY	-- Check the CAN-Bus terminal resistance. Refer to CAN-BUS TERMINAL RESISTANCE, CHECKING .
U0140 Lost Communication With Body Control Module	COM: Body Control Module (BCM) Communication With BCM	Received message no message	Time after ignition on 0.5 s	2.0 s Continuous	2 DCY	-- Check the CAN-Bus terminal resistance. Refer to CAN-BUS TERMINAL RESISTANCE, CHECKING .
U0146 Lost Communication With Gateway "A"	COM: Gateway Communication With Gateway	Received message no message	Time after ignition on 0.5 s	1.0 s Continuous	2 DCY	-- Check the CAN-Bus terminal resistance. Refer to CAN-BUS TERMINAL RESISTANCE, CHECKING .
U0155 Lost Communication With Instrument Panel Cluster (IPC) Control Module	COM: Instrument Panel Cluster (IPC) Communication With IPC	Received message no message	Time after ignition on 0.5 s	5.0 s Continuous	2 DCY	-- Check the CAN-Bus terminal resistance. Refer to CAN-BUS TERMINAL RESISTANCE, CHECKING .
U0302 Software Incompatibility With Transmission Control Module	COM: Transmission Control Module (TCM) Communication With TCM	Received A/T vehicle data TCM signal	Time after ignition on 0.5 s	5.0 s Continuous	2 DCY	-- Check for software updates and TSB's. Reprogram as necessary. If none are found, refer to appropriate repair information.
U0322 Software Incompatibility With Body Control Module	COM: Gateway Communication With Gateway	Ambient temperature sensor coding monitoring failure	Time after ignition on > 1.5 s	2.0 s Continuous	2 DCY	-- Check the CAN-Bus terminal resistance. Refer to CAN-BUS TERMINAL RESISTANCE, CHECKING .
U0415 Invalid Data Received From Anti-Lock Brake System (ABS) Control Module	Vehicle Speed Sensor (VSS) Rationality Check High	Vehicle speed > 202 mph		2.0 s Continuous	2 DCY	-- Check the CAN-Bus terminal resistance. Refer to CAN-BUS TERMINAL RESISTANCE, CHECKING .
	COM: Vehicle Speed Sensor (VSS) Communication With BSCM	Speed sensor signal: low voltage error 655.33 - 655.34km/h (no map, just bottom and top limit)	Time since engine running > 0.5 s Vehicle speed > 7 mph	0.5 s Continuous
		Speed sensor signal: initialization error 655.33 - 655.34 km/h (no map, just bottom and top limit)	Time since engine running > 0.5 s Vehicle speed < 7 mph	2.0 s Continuous
		Speed sensor signal: sensor error 655.35 km/h (no map, just bottom and top limit)	Time since engine running > 0.5 s	0.5 s Continuous
	COM: Brake System Control Module (BSCM) Communication With BSCM	Received data implausible message	Time after ignition on 0.5 s	0.5 s Continuous
U0422 Invalid Data Received From Body Control Module	COM: Body Control Module (BCM) Communication With BCM	Received dataimplausible message	Time after ignition on 0.5 s	1.0 s Continuous	2 DCY	-- Check the Outside Air Temperature Sensor -G17-. Refer to Outside Air Temperature Sensor - G17-, CHECKING .
U0422 Invalid Data Received From Body Control Module	COM: Gateway Communication With Gateway	Ambient temperature value (initialization) failure	Time after ignition on> 1.5 s Engine running	3.0 s Continuous	2 DCY
U0423 Invalid Data Received From Instrument Panel Cluster Control Module	COM: Instrument Panel Cluster (IPC) Communication With IPC	Received data implausible message	Time after ignition on 0.5 s	3.0 s Continuous	2 DCY	-- Check the CAN-Bus terminal resistance. Refer to CAN-BUS TERMINAL RESISTANCE, CHECKING .
	CAN: Instrument Panel Cluster (IPC) Communication With IPC	Received data signal out of valid range	Time after ignition on 0.5 s	3.0 s Continuous	2 DCY
U1103 Production Mode Active	Engine Control Module (ECM): Production Mode Function Monitoring: Mode Change	Production mode active	Vehicle speed < 3 mph Max trip mileage since initial vehicle start-up < 62.15 miles During ECM keep alive-time after ignition off Engine speed 0 RPM For hybrid: Drive motor off	0.01 s Continuous	1 DCY	-- Vehicle in production mode. Refer to appropriate repair information for resolution. Note the mode can be deactivated with a factory scan tool or will automatically turn off after vehicle accumulates the first 100 km (62.14 miles) of driving.