Electronic Brake Boost Control Module, 2015 - 2018 My

DTC	Error Message	Malfunction Criteria and Threshold Value	Secondary Parameters with Enable Conditions	Monitoring Time Length	Frequency of checks, MIL Illum
P0560	System Voltage	Voltage sensor 1 - voltage sensor 3 > 4.5 V	EBBC state running Or Shutdown Vehicle speed > 1.8 m/s Electric motor not controlled	96.0 s	2 DCY Continuous
P0562	System Voltage Low	Voltage sensor 3 < 4.9 V	EBBC state running Or Shutdown	200.0 ms	2 DCY Continuous
P0563	System Voltage High	Voltage sensor 3 > 19.8 V	EBBC state running Or Shutdown Vehicle speed > 1.8 m/s	90.0 s	2 DCY Continuous
P057B	Brake Pedal Position Sensor "A" Circuit Range/Performance	BPTS A gradient < -2, 000 mm/s	None	5.0 ms	2 DCY Continuous
		BPTS A PWM frequency < 879.3 1/s Or BPTS A PWM frequency > 1127.17 1/s	EBBC state running Or Shutdown	100.0 ms
		BPTS A PWM duty cycle < 7.32% Or BPTS A PWM duty cycle > 92.83%	EBBC state running Or Shutdown	100.0 ms
P057C	Brake Pedal Position Sensor "A" Circuit Low	BPTS A signal line rising or falling edge of BPTS A PWM < 0.3 V Not detected	EBBC state running Or Shutdown	30.0 ms	2 DCY Continuous
P057D	Brake Pedal Position Sensor "A" Circuit High	BPTS A signal line rising or falling edge of BPTS A PWM > 4.7 V Not detected	EBBC state running Or Shutdown	30.0 ms	2 DCY Continuous
P05DC	Brake Pedal Position Sensor "B" Circuit Range/Performance	BPTS B gradient < -2, 000 mm/s	None	5.0 ms	2 DCY Continuous
		BPTS B PWM frequency < 879.3 1/s Or BPTS B PWM frequency > 1127.17 1/s	EBBC state running Or Shutdown	100.0 ms
		BPTS B PWM duty cycle < 7.32% Or BPTS B PWM duty cycle > 92.83%	EBBC state running Or Shutdown	100.0 ms
P05DD	Brake Pedal Position Sensor "B" Circuit Low	BPTS B signal line rising or falling edge of BPTS B PWM < 0.3 V not detected	EBBC state running Or Shutdown	30.0 ms	2 DCY Continuous
P05DE	Brake Pedal Position Sensor "B" Circuit High	BPTS B signal line rising or falling edge of BPTS B PWM > 4.7 V not detected	EBBC state running Or Shutdown	30.0 ms	2 DCY Continuous
P05E0	Brake Pedal Position Sensor "A"/"B" Correlation	BPTS A - BPTS B > 1 mm	BPTS A Or BPTS B > 42 mm > 42 mm	500.0 s	2 DCY Continuous
		BPTS A - BPTS B > 0.5 mm	BPTS A signal BPTS B signal <= 42 mm <= 42 mm	500.0 s	2 DCY Continuous
		BPTS A + BPTS B) / 2 > 0.6 mm (BPTS A + BPTS B) / 2 < 1.5 mm	EBBC state running Or Shutdown Vehicle speed > 2 m/s Brake pedal not applied	60.0 s	2 DCY Continuous
P0604	Internal Control Module Random Access Memory (RAM) Error	Multi bit failure detected true Or Coupling failure detected true Or Address decoder test detects an error true	None	Immediately	0 DCY Continuous
		March 13 test detects a fault true	EBBC state init		0 DCY Once
		RAM cell <>'0' Or SRAM cell <> '0'	EBBC state init		0 DCY Once
		Number of detected single-bit errors > 2	EBBC state running Or Shutdown		2 DCY Continuous
P0607	Control Module Performance	Baud rate timing check not ok Or Mask register check not ok Or Arbitration register check not ok	EBBC state running	10.0 ms	2 DCY Continuous
		Communication time out between CAN-core and RAM detected true	EBBC state running	10.0 ms	2 DCY Continuous
		Data abort occurred true Or Pre fetch abort occurred true Or Undefined instruction occurred true	None	Immediately	0 DCY Continuous
		Current start time of a task > ideal start time + 5%		Immediately	2 DCY Continuous
		ADC reference voltage Or ADC reference voltage < 1.145 V > 1.345 V		20.0 ms	2 DCY Continuous
		BMS switched on	EBBC state init Watchdog trigger missed Or Watchdog trigger timing wrong	800.0 ms	2 DCY Once
		Error pin event counter not incremented	EBBC state init	1, 000.0 ms	2 DCY Once
		HETOFF1 - failure detected flag true	None	Immediately	0 DCY Continuous
		HETTU status - pointer error flag true
		HETTU status - bus error flag true
		HETTU status - busy error flag true
		INTOFF0 - failure detected flag true
		Watchdog detects a missing task true
		Defined frequency - calculated frequency \| / defined frequency > 5%	EBBC state running Or Shutdown	15.0 ms	2 DCY Continuous
		Charge-pump failure bit true Or Clock-input-signal failure bit true Or Internal-oscillator-circuit failure bit true	EBBC state init	200.0 ms	2 DCY Continuous
		Voltage comparator test error flag set		200.0 ms	2 DCY Once
		EEPROM cell is empty true		Immediately	2 DCY Once
		Task exception occurred true	EBBC state running Or Shutdown	Immediately	0 DCY Continuous
		PDUR initialization false		10.0 ms	2 DCY Continuous
		PDU buffer overrun detected		10.0 ms	2 DCY Continuous
		Number of EEPROM cells where BPTS calibration value is empty >= 1	EBBC state init	Immediately	2 DCY Once
		EEPROM cell is empty true	EBBC state init		2 DCY Once
		Check-word at begin of stack has changed Or Check-word at end of stack has changed true	EBBC state running Or Shutdown		0 DCY Continuous
		Not supported software interrupt occurred true Or Non implemented interrupt occurred true Or Interrupt lock release is called without previous lock true Or Not all interrupts are released true Or Interrupt lock time > 0.07 ms	None		0 DCY Continuous
		Voltage pre-regulator mode failure bit set	EBBC state running Or Shutdown	200.0 ms	2 DCY Continuous
P060B	Internal Control Module A/D Processing Performance	Number of conversions which could not be finished in time >= 10	None	3.0 ms	2 DCY Continuous
P060B	Internal Control Module A/D Processing Performance	Difference between the two ADC measurements per channel > 540 digits	None	200.0 ms	2 DCY Continuous
P060C	Internal Control Module Main Processor Performance	CCM self test false	EBBC state running	Immediately	0 DCY Once
		Double bit error detected Or Number of detected single bit errors > 1	None		0 DCY Continuous
		NMI occurred true	EBBC state init		0 DCY Once
		Error pin logical low	EBBC state running Or Shutdown		0 DCY Continuous
		No NMI occurred true Or Not expected NMI occurred true	EBBC state init		0 DCY Continuous
P0610	Control Module Vehicle Options Error	Production mode active	EBBC state running Or Shutdown	5.0 ms	0 DCY Continuous
P062F	Internal Control Module EEPROM Error	Read failure occurred true	EBBC state init	Immediately	0 DCY Once
		Stored customer ID <> expected customer ID			1 DCY Once
		PSW end marker has not been found true			1 DCY Once
		PDM data field size to allocate > available space in EEPROM	None		1 DCY Continuous
		EEPROM data field size stored <> data field size configuration in software	EBBC state init		1 DCY Once
		Writing operation read data > 25.0 ms Not equal to written data	EBBC state running Or Shutdown		2 DCY Continuous
		PDM flag set	EBBC state init		1 DCY Continuous
		Read failure occurred true			2 DCY Once
		Read failure occurred true		20.0 ms	2 DCY Once
U0001	High Speed CAN Communication Bus	CAN 2 bus state bus off	EBBC state running	280.0 ms	0 DCY Continuous
U0002	High Speed CAN Communication Bus Performance	No CAN 2 message received	EBBC state running	280.0 ms	0 DCY Continuous
U0100	Lost Communication With ECM/PCM "A"	Data length of engine ECU CAN message is not correct > 5 A CAN messages from engine ECU was not received > 5	EBBC state running	5, 000.0 ms	2 DCY Continuous
U0122	Lost Communication With Vehicle Dynamics Control Module	A CAN messages from BSCM ECU was not received > 25	EBBC state running	500.0 ms	2 DCY Continuous
U0167	Lost Communication With Vehicle Immobilizer Control Module	VIN received none	EBBC state init	5, 000.0 ms	2 DCY Once
U0401	Invalid Data Received From ECM/PCM "A"	Recalculated CRC does not match the received CRC > 0	EBBC state running	20.0 ms	2 DCY Continuous
U0401	Invalid Data Received From ECM/PCM "A"	Message counters of engine ECU CAN messages are not periodically incremented > 4	EBBC state running	4, 000.0 ms	2 DCY Continuous
U0416	Invalid Data Received From Vehicle Dynamics Control Module	Data length of gateway ECU CAN message is not correct > 10 A CAN messages from gateway ECU was not received >10	EBBC state running	1, 000.0 ms	2 DCY Continuous
		Message counters of BSCM ECU CAN messages are not periodically incremented > 25		500.0 ms
		Recalculated CRC does not match the received CRC > 0		20.0 ms
U0426	Invalid Data Received From Vehicle Immobilizer Control Module	Received VIN is at initialization value true	EBBC state init	20.0 ms	2 DCY Once
U1013	Control Module Not Coded	EEPROM variant code contained in SW false	EBBC state init	20.0 ms	2 DCY Once
U1013	Control Module Not Coded	EEPROM variant information empty	EBBC state init	20.0 ms	2 DCY Once
U103E	Brake Booster Control Module No Communication	Data length of EBBC ECU CAN message is not correct > 3	AHA state running	300.0 ms	2 DCY Continuous
U103E	Brake Booster Control Module No Communication	No CAN messages from EBBC ECU are received by AHA > 10	AHA state running	1, 000.0 ms	2 DCY Continuous
U103F	Brake Booster Control Module Implausible Signal	Message counters of EBBC ECU CAN messages are not periodically incremented > 5	AHA state running	100.0 ms	2 DCY Continuous
U103F	Brake Booster Control Module Implausible Signal	Recalculated CRC does not match the received CRC > 3	AHA state running	100.0 ms	2 DCY Continuous
U10B8	Local Data Bus Faulty	CAN 1 bus state bus off No CAN 1 message received > 10	EBBC state running	100.0 ms	2 DCY Continuous
U10B8	Local Data Bus Faulty	No CAN 2 message detected > 10	EBBC state running	200.0 ms	2 DCY Continuous
U111D	Brake Press. Accum. Control Module No Communication	Data length of AHA ECU CAN message is not correct > 10 A CAN messages from AHA ECU was not received > 10	EBBC state running	200.0 ms	2 DCY Continuous
U111E	Brake Press. Accum. Control Module Implausible Signal	Message counters of AHA ECU CAN messages are not periodically incremented > 4	EBBC state running	40.0 ms	2 DCY Continuous
U111E	Brake Press. Accum. Control Module Implausible Signal	Recalculated CRC does not match the received CRC > 3	EBBC state running	30.0 ms	2 DCY Continuous