Intake Manifold Runner Position Sensor - G336-, Checking

General Description

The Intake Manifold Runner Position Sensor -G336- monitors the position of the intake manifold runner flaps. These flaps can be adjusted open or closed to provide longer or shorter intake runners depending on ambient conditions to increase engine efficiency.

Special tools and workshop equipment required

Multimeter.
Wiring Diagram.
Scan Tool.

Test requirements

Fuses OK.
Battery voltage OK.
Switch OFF all electrical and electronic accessories.
Vehicles with automatic transmission, ensure the selector lever position is in "P".
Vehicles with manual transmission, ensure the shifter lever position is in "N" with the parking brake applied.
Observe all safety precautions: SAFETY PRECAUTIONS .
View clean working conditions: CLEAN WORKING CONDITIONS .

Test Procedure

Step	Procedure	Result / Action to Take
1	PERFORM: Preliminary Check to verify the customers complaint. Refer to PRELIMINARY CHECK . -- Was Complaint verified?	-- YES: GO TO: Step 2 Intake Manifold Runner Position Sensor - G336-, CHECKING => 2 . -- NO: GATHER more information from customer about the complaint.
2	IGNITION: OFF. DISCONNECT: Intake Manifold Runner Position Sensor -G336- harness connector. IGNITION: ON. CHECK: Intake Manifold Runner Position Sensor -G336- harness connector terminals 1 to 3 for voltage. IGNITION: OFF. SPECIFIED VALUE: About 5.0 V. -- Was Value obtained?	-- YES: GO TO: Step 3 Intake Manifold Runner Position Sensor - G336-, CHECKING => 3 . -- NO: GO TO: Step 4 Intake Manifold Runner Position Sensor - G336-, CHECKING => 4 .
3	REMOVE: Engine Control Module - J623-. Refer to appropriate repair information. CHECK: Intake Manifold Runner Position Sensor -G336- harness connector terminal 2 to the Engine Control Module - J623- harness connector T60 / 59 for resistance. SPECIFIED VALUE: 0.5 Ω (± 0.3 Ω). -- Was Value obtained?	-- YES: REPLACE: Intake Manifold Runner Position Sensor -G336-. Refer to appropriate repair information. GO TO: Step 5 Intake Manifold Runner Position Sensor - G336-, CHECKING => 5 . -- NO: PERFORM: Visual Inspection of wiring and component. CHECK: Wiring for open, high resistance, short or harness connector for damage, corrosion, loose or broken terminals. REPAIR: Faulty wiring or connector. GO TO: Step 5 Intake Manifold Runner Position Sensor - G336-, CHECKING => 5 .
4	REMOVE: Engine Control Module - J623-. Refer to appropriate repair information. CHECK: Intake Manifold Runner Position Sensor -G336- harness connector terminal 1 to the Engine Control Module - J623- harness connector T60 / 27 for resistance. CHECK: Intake Manifold Runner Position Sensor -G336- harness connector terminal 3 to the Engine Control Module - J623- harness connector T60 / 13 for resistance. SPECIFIED VALUE: 0.5 Ω (± 0.3 Ω). -- Were Values obtained?	-- YES: GO TO: Step 5 Intake Manifold Runner Position Sensor - G336-, CHECKING => 5 . -- NO: PERFORM: Visual Inspection of wiring and component. CHECK: Wiring for open, high resistance, short or harness connector for damage, corrosion, loose or broken terminals. REPAIR: Faulty wiring or connector. GO TO: Step 5 Intake Manifold Runner Position Sensor - G336-, CHECKING => 5 .
5	Final Procedure Perform a road test to verify repair. -- Does the original DTC return?	-- YES: CHECK: Engine Control Module -J623- harness connector for any damaged, pushed-out pins. REPAIR: As necessary. If all electrical connections are OK: REPLACE: Engine Control Module -J623-. Refer to appropriate repair information. Clear the DTC's. Refer to DIAGNOSTIC MODE 04 - ERASE DTC MEMORY . Repair is complete. Generate Readiness Code. Refer to READINESS CODE . Return vehicle to Customer. -- NO: Perform the diagnostic procedure for any DTC's. If no DTC's return, the repair is complete. Return vehicle to customer.