Rear Peripheral Camera -R246- CALIBRATING

The Rear Peripheral Camera -R246- is installed in the rear lid handle button.

Special Tools And Workshop Equipment Required 

• Calibration Tool :VAS6350 
• Peripheral Camera Calibration Device :VAS6350/6 
• Vehicle Diagnostic Tester

-- Set-up requirements Calibration Tool .

-- Install and align the :VAS6350  with : VAS6350/6  . Refer to Calibration Tool .

-- Connect the Vehicle Diagnostic Tester.

Setting Up The Calibration Device 

:VAS6350/1  installing:

-- Check the dimension of the holes.

-- Equip the :VAS6350/1  appropriately. Use spacer pieces.

-- To do so, secure three wheel bolt adapters in the hole circle to each :VAS6350/1  .

-- Place the paddle on both :VAS6350/1  and secure them using a clamping screw.

-- Place the :VAS6350/1  onto the wheel bolts on the rear wheels.

The :VAS6350/1  are positioned by the "O rings" in the adapters and held in place.

Courtesy of AUDI OF AMERICA, LLC

-- Adjust the paddle with aid of lock bolts so that they move freely just above the floor. Make sure that the paddle is easily accessible.

:VAS6350  with :VAS6350/6  Orientation

-- Position the :VAS6350  with the :VAS6350/6  -2- at a distance of between 400 mm and 600 mm -dimension B- in the rear of the vehicle in the center (in behind of the rear bumper trim).

Courtesy of AUDI OF AMERICA, LLC

-- Move the calibration field on the :VAS6350  into a horizontal position.

-- To do so, twist plastic feet under the calibration field of the :VAS6350  so that air bubble in level is located exactly in the center of the indicator -arrow-

Courtesy of AUDI OF AMERICA, LLC

-- Attach the :VAS6350/3  -4- to the :VAS6350  to the center of the location provided.

Courtesy of AUDI OF AMERICA, LLC

-- Switch on the :VAS6350/3  -4- on the calibration field of the :VAS6350  and align the entire :VAS6350  with :VAS6350/6  so that the laser beam of the :VAS6350/3  hits the center of vehicle rear above the Audi rings.

-- Make sure the Audi rings are centered on the rear. Correct the laser beam accordingly.

Distance Measurement 

-- Switch on the :VAS6350/2  .

Courtesy of AUDI OF AMERICA, LLC

The display shows how to stop the :VAS6350/2  . Press the corresponding button.

Courtesy of AUDI OF AMERICA, LLC

1. Attach with front edge
2. Attach with rear edge

-- Hold the :VAS6350/2  -2- flush in the bracket on one side of the :VAS6350  (attach with rear edge). The :VAS6350/2  -2- must sit securely on the bracket.

Courtesy of AUDI OF AMERICA, LLC

-- Press the measuring button briefly.

The laser turns on.

-- Make sure that laser beam from :VAS6350/2  -2- hits lower, enlarged part of paddle -1-.

If this is not the case, paddles must be corrected accordingly via clamping screws on the :VAS6350/1  .

-- Use one hand to secure the :VAS6350/2  in the bracket on the :VAS6350  while the laser beam is visible on the paddle.

-- Then press the measuring button for distance measurement briefly.

-- Repeat this measurement on the other side of the :VAS6350  in the same way for the rear wheel.

The distance value must be the same on both sides.

If values are not identical:

-- Align the :VAS6350  long enough so that both sides are identical.

Pay attention when aligning the calibration field of the :VAS6350  , that the :VAS6350/3  from the :VAS6350  strikes the center of the Audi rings and the indicator of the level remains centered. Adjust if necessary.

-- Make note of the distance dimension measured.

Dimension Measurement -h-

-- Measure the height of the :VAS6350  -2- calibration field, dimension -h-, from the surface of the :VAS6350  -2- calibration field (not the aluminum frame) down to the floor. Measure the hole in the :VAS6350  -2- calibration field.

Courtesy of AUDI OF AMERICA, LLC

Make sure the :VAS6350/2  -1- is adjusted correctly (attach with front edge).

The display shows how to stop the :VAS6350/2  . Press the corresponding button.

Courtesy of AUDI OF AMERICA, LLC

1. Attach with front edge
2. Attach with rear edge

Dimension -h- and the distance dimension must now be entered into the Vehicle Diagnostic Tester in "millimeters".

Performing Calibration 

Vehicle Diagnostic Tester is attached.

-- Select the Diagnostic  mode and start the diagnostics.

-- Select the tab Test Plan  .

-- Select Select Individual Tests  and choose the following sequence.

• Body
• Electrical Equipment
• 01 - OBD-capable systems
• 6C - peripheral camera control module | J928
• 6C - peripheral camera control module, functions
• 6C - Calibration, (Repair Group 91)

The Vehicle Diagnostic Tester continues with the calibrating procedure from here on.