Specifications Index
SPECIFICATIONS INDEX
| System | Specification/Procedure | |||
|---|---|---|---|---|
| Air Conditioning | ||||
| Service | ||||
| R1234yf | WORKING WITH A/C SERVICE STATION (1 OF 2) or WORKING WITH A/C SERVICE STATION (2 OF 2) | |||
| R134a | AIR CONDITIONING (REFRIGERANT R134A SERVICING) (1 OF 2) or AIR CONDITIONING (REFRIGERANT R134A SERVICING) (2 OF 2) | |||
| Torque | OVERVIEW - A/C COMPRESSOR POWER UNIT | |||
| Axle Nut/Hub Nut/Wheel Bearing Unit | ||||
| Front | 200 Nm +180° | |||
| Rear | Refer to the appropriate procedure i OVERVIEW - WHEEL BEARING | |||
| Battery | BATTERY | |||
| Brakes | ||||
| Bleeding Sequence | HYDRAULIC SYSTEM, BLEEDING | |||
| Disc Brakes | ||||
| Front | Refer to the appropriate procedure in FRONT BRAKES | |||
| Rear | Refer to the appropriate procedure in REAR BRAKES | |||
| Torque | ||||
| Front | FRONT BRAKES | |||
| Rear | REAR BRAKES | |||
| Charging | ||||
| Generator | GENERATOR | |||
| Torque | OVERVIEW - GENERATOR | |||
| Drive Belts | ||||
| Adjustment | ||||
| 2.0L Engine(s) DLHB | RIBBED BELT, REMOVING AND INSTALLING | |||
| 2.9L Engine(s) DKMB & 3.0L Engine(s) DLZA | RIBBED BELT, REMOVING AND INSTALLING | |||
| Belt Routing | ||||
| 2.0L Engine(s) DLHB | OVERVIEW - CYLINDER BLOCK, BELT PULLEY SIDE | |||
| 2.9L Engine(s) DKMB & 3.0L Engine(s) DLZA | OVERVIEW - CYLINDER BLOCK, BELT PULLEY SIDE | |||
| Engine Cooling | ||||
| General Service Specifications | Refer to the appropriate FLUID CAPACITY TABLES information. | |||
| Radiator Cap Pressure | ||||
| 2.0L Engine(s) DLHB | Checking the Pressure Relief Valve in the Version 1 Cap | |||
| 2.9L Engine(s) DKMB & 3.0L Engine(s) DLZA | Checking the Pressure Relief Valve in the Version 1 Cap | |||
| Thermostat R & I | N/A | |||
| Water Pump R & I | ||||
| 2.0L Engine(s) DLHB | Refer to the appropriate procedure in COOLANT PUMP/COOLANT THERMOSTAT | |||
| 2.9L Engine(s) DKMB & 3.0L Engine(s) DLZA | Refer to the appropriate procedure in COOLANT PUMP/COOLANT THERMOSTAT | |||
| Engine Mechanical | ||||
| 2.0L Engine(s) DLHB | ||||
| Compression | COMPRESSION, CHECKING | |||
| Oil Pressure | OIL PRESSURE, CHECKING | |||
| Idle | 12.3 to 23.2 psi (0.85 to 1.6 bar) | |||
| 2, 000 RPM | 17.4 to 23.2 psi (1.2 to 1.6 bar) | |||
| 3, 700 RPM | 17.4 to 23.2 psi (1.2 to 1.6 bar) | |||
| Overhaul | Refer to the appropriate procedure in ENGINE ASSEMBLY or CYLINDER HEAD, VALVETRAIN or CRANKSHAFT, CYLINDER BLOCK | |||
| Torque | Refer to the appropriate procedure in ENGINE ASSEMBLY or CYLINDER HEAD, VALVETRAIN or CRANKSHAFT, CYLINDER BLOCK | |||
| 2.9L Engine(s) DKMB & 3.0L Engine(s) DLZA | ||||
| Compression | COMPRESSION, CHECKING | |||
| Oil Pressure | OIL PRESSURE, CHECKING | |||
| Idle | minimum 13.05 psi (0.9 bar) | |||
| 2, 000 RPM | minimum 18.85 psi (1.3 bar) | |||
| Overhaul | Refer to the appropriate procedure in ENGINE ASSEMBLY or CYLINDER HEAD, VALVETRAIN or CRANKSHAFT, CYLINDER BLOCK | |||
| Torque | Refer to the appropriate procedure in ENGINE ASSEMBLY or CYLINDER HEAD, VALVETRAIN or CRANKSHAFT, CYLINDER BLOCK | |||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. | |||
| Engine Oil Drain Plug (2.0L & 2.9L) | 30Nm | |||
| Flywheel/Flex Plate Torque | 60 Nm + 90° | |||
| Fuel System | ||||
| Fuel Pressure & Test Procedure | Transfer Fuel Pump -G6-, CHECKING | |||
| Ignition | ||||
| Firing Order & Cylinder Identification | FIRING ORDER & CYLINDER IDENTIFICATION | |||
| Ignition Wires | Coil-On-Plug | |||
| Spark Plug | N/A | |||
| Starting | ||||
| Starter | STARTER | |||
| Torque | OVERVIEW - STARTER | |||
| Wheel Alignment | ||||
| Adjustment Specifications | AXLE ALIGNMENT SPECIFIED VALUES | |||
| Torque | ||||
| Front | FASTENER TIGHTENING SPECIFICATIONS or FASTENER TIGHTENING SPECIFICATIONS | |||
| Rear | FASTENER TIGHTENING SPECIFICATIONS or FASTENER TIGHTENING SPECIFICATIONS | |||
| Wheel & Tire | ||||
| Wheel Lug Nut Torque | 120 Nm | |||