Specifications Index

SPECIFICATIONS INDEX

System			Specification/Procedure
Air Conditioning
Service			WORKING WITH A/C SERVICE STATION (R1234yf) (1 of 2) and WORKING WITH A/C SERVICE STATION (R1234yf) (2 of 2) or A/C SYSTEM, GENERAL INFORMATION (R134A)
Torque			Refer to the appropriate procedure in OVERVIEW - A/C COMPRESSOR POWER UNIT
Axle Nut/Hub Nut
Front			200 Nm +180°
Rear			200 Nm +180°
Battery			BATTERY
Brakes
Bleeding Sequence			HYDRAULIC SYSTEM, BLEEDING
Disc Brakes			FRONT BRAKES REAR BRAKES
Torque			Refer to the appropriate procedures, Hydraulic Components 47 HYDRAULIC COMPONENTS Mechanical Components FRONT BRAKES / REAR BRAKES
Charging
Generator			GENERATOR
Torque			OVERVIEW - GENERATOR
Drive Belts
Adjustment
2.0L			RIBBED BELT, REMOVING AND INSTALLING [DMTA, DPAA, DPUA, DPVA, DMTC]
	3.0L		RIBBED BELT, REMOVING AND INSTALLING [CWGD, DECA, CZSE, DLZA, DKMB, CZSA, DCBD, DCBE]
Belt Routing
		2.0L	OVERVIEW - CYLINDER BLOCK, BELT PULLEY SIDE
	3.0L		OVERVIEW - CYLINDER BLOCK, BELT PULLEY SIDE
Engine Cooling
General Service Specifications			Refer to the appropriate FLUID CAPACITY TABLES information.
Radiator Cap Pressure
	Blue Cap		1.4 to 1.6 bar (20.30 to 23.20 psi)
	Black Cap		1.6 to 1.8 bar (23.2 to 26.1 psi)
Thermostat R & I
2.0L			OVERVIEW - COOLANT PUMP/COOLANT THERMOSTAT
	3.0L		OVERVIEW - COOLANT PUMP/COOLANT THERMOSTAT
Water Pump R & I
2.0L			COOLANT PUMP, REMOVING AND INSTALLING
	3.0L		COOLANT PUMP, REMOVING AND INSTALLING
Engine Mechanical
2.0L
		Compression	COMPRESSION, CHECKING
Oil Pressure			OIL FILTER/OIL PRESSURE SWITCH - 2.0L
Overhaul			10 ENGINE ASSEMBLY , 13 CRANKSHAFT, CYLINDER BLOCK and 15 CYLINDER HEAD, VALVETRAIN
Torque			Refer to the appropriate procedure in 10 ENGINE ASSEMBLY , 13 CRANKSHAFT, CYLINDER BLOCK and 15 CYLINDER HEAD, VALVETRAIN
3.0L
	Compression		COMPRESSION, CHECKING
	Oil Pressure		OIL FILTER/OIL PRESSURE SWITCH - 3.0L
	Overhaul		10 ENGINE ASSEMBLY , 13 CRANKSHAFT, CYLINDER BLOCK and 15 CYLINDER HEAD, VALVETRAIN
	Torque		Refer to the appropriate procedure in 10 ENGINE ASSEMBLY , 13 CRANKSHAFT, CYLINDER BLOCK and 15 CYLINDER HEAD, VALVETRAIN
Fluid Specifications			See FLUIDS under MAINTENANCE tab.
Engine Oil Drain Plug			30Nm
Flywheel/Flex Plate Torque			60 Nm + 90°
Fuel System
Fuel Pressure Test Procedure
	2.0L		Transfer Fuel Pump -G6-, CHECKING
	3.0L		Transfer Fuel Pump -G6-, CHECKING
Ignition
Firing Order & Cylinder Identification			FIRING ORDER & CYLINDER IDENTIFICATION
Spark Plug
2.0L			N/A
	3.0L		N/A
Starting
Starter			STARTER
Torque			OVERVIEW - STARTER
Wheel Alignment
Adjustment Specifications			AXLE ALIGNMENT
Torque			40 FRONT SUSPENSION 42 REAR SUSPENSION
Wheel & Tire
Wheel Lug Nut Torque			140 Nm