Specifications Index
SPECIFICATIONS INDEX
| System | Specification/Procedure | |||
|---|---|---|---|---|
| Air Conditioning | ||||
| Service | ||||
| R1234yf | WORKING WITH A/C SERVICE STATION (1 OF 2) / WORKING WITH A/C SERVICE STATION (2 OF 2) | |||
| R134a | Air Conditioning (Refrigerant R134a Servicing - Pressure Checking) (1 Of 3) / Air Conditioning (Refrigerant R134a Servicing - Refrigerant Circuit) (2 Of 3) / Air Conditioning (Refrigerant R134a Servicing) (3 Of 3) | |||
| Torque | N/A | |||
| Axle Nut/Hub Nut/Wheel Bearing Unit | ||||
| Front | 200 Nm +180° | |||
| Rear | 200 Nm +180° | |||
| Battery | BATTERY | |||
| Brakes | ||||
| Bleeding Sequence | HYDRAULIC SYSTEM, BLEEDING / HYDRAULIC SYSTEM, BLEEDING (CWGD) | |||
| Disc Brakes | ||||
| Front | FRONT BRAKES / FRONT BRAKES (CWGD) | |||
| Rear | REAR BRAKES / REAR BRAKES (CWGD) | |||
| Torque | ||||
| Front | OVERVIEW - FRONT BRAKES / FRONT BRAKES (CWGD) | |||
| Rear | OVERVIEW - REAR BRAKES / OVERVIEW - REAR BRAKES (CWGD) | |||
| Charging | ||||
| Generator | GENERATOR | |||
| Torque | OVERVIEW - GENERATOR | |||
| Drive Belts | ||||
| Adjustment | ||||
| 2.0L | Ribbed Belt, Removing And Installing | |||
| 3.0L | Ribbed Belt, Removing And Installing | |||
| Belt Routing | ||||
| 2.0L | Overview - Cylinder Block, Belt Pulley Side | |||
| 3.0L | Overview - Cylinder Block, Belt Pulley Side | |||
| Engine Cooling | ||||
| General Service Specifications | Refer to the appropriate FLUID CAPACITY TABLES information. | |||
| Radiator Cap Pressure | ||||
| 2.0L | Checking The Pressure Relief Valve In The Version 1 Cap | |||
| 3.0L | Checking The Pressure Relief Valve In The Version 1 Cap | |||
| Thermostat R & I | N/A | |||
| Water Pump R & I | ||||
| 2.0L | Coolant Pump/Coolant Thermostat | |||
| 3.0L | Coolant Pump/Coolant Thermostat | |||
| Engine Mechanical | ||||
| 2.0L | ||||
| Compression | Compression, Checking (DMSA) Compression, Checking (DPAA) |
|||
| Oil Pressure | Oil Pressure, Checking (DMSA) Oil Pressure, Checking (DPAA) |
|||
| Idle | 12.3 to 23.2 psi (0.85 to 1.6 bar) | |||
| 2, 000 RPM | 17.4 to 23.2 psi (1.2 to 1.6 bar) | |||
| 3, 700 RPM | 17.4 to 23.2 psi (1.2 to 1.6 bar) | |||
| Overhaul | Refer to the appropriate procedure in Engine Assembly (DMSA) or Engine Assembly (DPAA) | |||
| Torque | Refer to the appropriate procedure in Engine Assembly (DMSA) or Engine Assembly (DPAA) | |||
| 3.0L | ||||
| Compression | Compression, Checking | |||
| Oil Pressure | Oil Pressure, Checking | |||
| Idle | minimum 0.9 bar (13.05 psi) | |||
| 2, 000 RPM | minimum 1.3 bar (18.85 psi) | |||
| Overhaul | Refer to the appropriate procedure in ENGINE ASSEMBLY | |||
| Torque | Refer to the appropriate procedure in ENGINE ASSEMBLY | |||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. | |||
| Engine Oil Drain Plug (3.0L) | 30Nm | |||
| Engine Oil Drain Plug (2.0L) | 30Nm | |||
| Flywheel/Flex Plate Torque | 60 Nm + 90° | |||
| Fuel System | ||||
| Fuel Pressure & Test Procedure | Transfer Fuel Pump -G6-, Checking | |||
| Ignition | ||||
| Firing Order & Cylinder Identification | Firing Order & Cylinder Identification | |||
| Ignition Wires | N/A | |||
| Spark Plug | N/A | |||
| Starting | ||||
| Starter | Starter | |||
| Torque | Overview - Starter | |||
| Wheel Alignment | ||||
| Adjustment Specifications | AXLE ALIGNMENT SPECIFIED VALUES | |||
| Wheel & Tire | ||||
| Wheel Lug Nut Torque | 120 Nm | |||