| Air Conditioning |
| Service |
| |
R1234yf |
WORKING WITH A/C SERVICE STATION (R1234YF) (A/C SERVICE STATION) (1 OF 2)
/ WORKING WITH A/C SERVICE STATION (R1234YF) (REFRIGERANT CIRCUIT) (2 OF 2) |
| |
R134a |
AIR CONDITIONING (REFRIGERANT R134A SERVICING) (PRESSURES, CHECKING) (1 OF 3)
/ AIR CONDITIONING (REFRIGERANT R134A SERVICING) (REFRIGERANT CIRCUIT COMPONENTS) (2 OF 3)
/ AIR CONDITIONING (REFRIGERANT R134A SERVICING) (REFRIGERANT CAPACITIES) (3 OF 3) |
| Torque |
N/A |
| Axle Nut/Hub Nut/Wheel Bearing Unit |
| Front |
200 Nm +180° |
| Rear |
200 Nm +180° |
| Battery |
BATTERY |
| Brakes |
| Bleeding Sequence |
HYDRAULIC SYSTEM, BLEEDING
/ HYDRAULIC SYSTEM, BLEEDING (CWGD) |
| Disc Brakes |
| |
Front |
FRONT BRAKES
/ FRONT BRAKES (CWGD) |
| |
Rear |
REAR BRAKES
/ REAR BRAKES (CWGD) |
| Torque |
| |
Front |
OVERVIEW - FRONT BRAKES
/ FRONT BRAKES (CWGD) |
| |
Rear |
OVERVIEW - REAR BRAKES
/ OVERVIEW - REAR BRAKES (CWGD) |
| Charging |
| Generator |
GENERATOR |
| Torque |
OVERVIEW - GENERATOR |
| Drive Belts |
| Adjustment |
| 2.0L |
RIBBED BELT, REMOVING AND INSTALLING (DMSA)
RIBBED BELT, REMOVING AND INSTALLING (DPAA) |
| 3.0L |
RIBBED BELT, REMOVING AND INSTALLING (CWGD) |
| Belt Routing |
| 2.0L |
OVERVIEW - CYLINDER BLOCK, BELT PULLEY SIDE (DMSA)
OVERVIEW - CYLINDER BLOCK, BELT PULLEY SIDE (DPAA) |
| 3.0L |
OVERVIEW - CYLINDER BLOCK, BELT PULLEY SIDE (CWGD) |
| Engine Cooling |
| General Service Specifications |
Refer to the appropriate FLUID CAPACITY TABLES information. |
| Radiator Cap Pressure |
| 2.0L |
CHECKING THE PRESSURE RELIEF VALVE IN THE VERSION 1 CAP (DMSA)
CHECKING THE PRESSURE RELIEF VALVE IN THE VERSION 1 CAP (DPAA) |
| 3.0L |
CHECKING THE PRESSURE RELIEF VALVE IN THE VERSION 1 CAP (CWGD) |
| Thermostat R & I |
N/A |
| Water Pump R & I |
| 2.0L |
COOLANT PUMP/COOLANT THERMOSTAT (DMSA)
COOLANT PUMP/COOLANT THERMOSTAT (DPAA) |
| 3.0L |
COOLANT PUMP/COOLANT THERMOSTAT (CWGD) |
| Engine Mechanical |
| 2.0L |
| |
|
Compression |
COMPRESSION, CHECKING (DMSA)
COMPRESSION, CHECKING (DPAA) |
| Oil Pressure |
OIL PRESSURE, CHECKING (DMSA)
OIL PRESSURE, CHECKING (DPAA) |
| |
|
Idle |
12.3 to 23.2 psi (0.85 to 1.6 bar) |
| |
|
2, 000 RPM |
17.4 to 23.2 psi (1.2 to 1.6 bar) |
| |
|
3, 700 RPM |
43.51 to 58.02 psi (3.0 to 4.0 bar) |
| Overhaul |
Refer to the appropriate procedure in ENGINE ASSEMBLY (DMSA)
or ENGINE ASSEMBLY (DPAA) |
| Torque |
Refer to the appropriate procedure in ENGINE ASSEMBLY (DMSA)
or ENGINE ASSEMBLY (DPAA) |
| 3.0L |
| |
|
Compression |
COMPRESSION, CHECKING |
| Oil Pressure |
OIL PRESSURE, CHECKING |
| |
|
Idle |
minimum 0.9 bar (13.05 psi) |
| |
|
2, 000 RPM |
minimum 1.3 bar (18.85 psi) |
| Overhaul |
Refer to the appropriate procedure in ENGINE ASSEMBLY |
| Torque |
Refer to the appropriate procedure in ENGINE ASSEMBLY |
| Fluid Specifications |
See FLUIDS under MAINTENANCE tab. |
| Engine Oil Drain Plug |
30Nm |
| Flywheel/Flex Plate Torque |
60 Nm + 90° |
| Fuel System |
| Fuel Pressure & Test Procedure |
TRANSFER FUEL PUMP -G6-, CHECKING |
| Ignition |
| Firing Order & Cylinder Identification |
FIRING ORDER & CYLINDER IDENTIFICATION |
| Ignition Wires |
N/A |
| Spark Plug |
N/A |
| 2.0L (DMSA) |
06Q 905 601 A |
| |
2.0L (DPAA) |
| 3.0L |
06M 905 606 F |
| Starting |
| Starter |
STARTER |
| Torque |
OVERVIEW - STARTER |
| Wheel Alignment |
| Adjustment Specifications |
AXLE ALIGNMENT SPECIFIED VALUES |
| Wheel & Tire |
| Wheel Lug Nut Torque |
120 Nm |