Specifications Index
CENTURY & REGAL SPECIFICATIONS INDEX
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning - Automatic System | |||
| Service | SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Air Conditioning - Manual System | |||
| Service | SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Axle Nut/Hub Nut | |||
| Front | 159 Ft. Lbs. (215 N.m) | ||
| Battery | BATTERY USAGE | ||
| Brakes | |||
| Bleeding Sequence | BLEEDING BRAKE SYSTEM | ||
| Disc Brakes | DISC BRAKE SPECIFICATIONS | ||
| Drum Brakes | DRUM BRAKE SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Charging | |||
| Generator | ON-VEHICLE TESTING | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Drive Belts | |||
| Adjustment | BELT ADJUSTMENT | ||
| Belt Routing | See appropriate illustration under SERPENTINE BELT ROUTING & ALIGNMENT | ||
| Engine Cooling | |||
| Service | COOLING SYSTEM SPECIFICATIONS | ||
| Radiator Cap Pressure | 15 psi or pressure stamped on cap | ||
| Thermostat R&I | |||
| 3.1L | THERMOSTAT | ||
| 3.8L | THERMOSTAT REPLACEMENT | ||
| Water Pump R&! | |||
| 3.1L | WATER PUMP | ||
| 3.8L | WATER PUMP | ||
| Engine Mechanical | |||
| 3.1L | |||
| Compression | Lowest compression reading should not be less than 70 percent of highest compression reading. No cylinder compression reading should be less than 100 psi (7.0 kg/cm2 ). | ||
| Oil Pressure | Minimum allowable oil pressure is 15 psi (1 kg/cm2 ) at 1100 RPM. | ||
| Overhaul | ENGINE SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| 3.8L | |||
| Compression | Lowest compression reading should not be less than 70 percent of highest compression reading. No cylinder compression reading should be less than 100 psi (7.0 kg/cm2 ). | ||
| Oil Pressure | With engine at normal operating temperature, oil pressure (with 5W-30 or 10W-30 engine oil) should be 60 psi (4.2 kg/cm2 ) at 1850 RPM. | ||
| Overhaul | ENGINE SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Fuel System | |||
| Pressure Specification | FUEL PUMP | ||
| Fuel Pressure Test Procedure | FUEL SYSTEM PRESSURE TEST (EXCEPT SATURN) | ||
| Fuel Filter Location and R & I | REMOVAL PROCEDURE (CENTURY, REGAL) | ||
| Flywheel/Flexplate | |||
| 3.1L | 52 Ft. Lbs. (71 N.m) Apply Thread Locker (12345382) to flexplate/flywheel bolts. |
||
| 3.8L | |||
| Step 1 | 11 Ft. Lbs. (15 N.m) | ||
| Step 2 | Additional 50 Degrees | ||
| Ignition | |||
| Firing Order | See FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires (Resistance) | HIGH TENSION WIRE RESISTANCE | ||
| Ignition Wires (Routing) | See Figure under Ignition Coil Module R&I For Spark Plug Wire To Coil Placement. REMOVAL & INSTALLATION | ||
| Spark Plugs | SPARK PLUGS | ||
| Starting | |||
| Starter | ON-VEHICLE TESTING | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Wheel Alignment | |||
| Adjustment | WHEEL ALIGNMENT SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Wheel & Tire | |||
| Lug Nut Torque | 103 Ft. Lbs (140 N.m) | ||