Specifications Index
ALLURE (CANADIAN) & LACROSSE SPECIFICATIONS INDEX
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | REFRIGERANT SYSTEM CAPACITIES | ||
| Torque | Automatic SystemFASTENER TIGHTENING SPECIFICATIONS Manual System FASTENER TIGHTENING SPECIFICATIONS |
||
| Axle Nut/Hub Nut | |||
| Front | NEW Nut 118 lb ft (160 N.m) | ||
| Battery | BATTERY USAGE | ||
| Brakes | |||
| Bleeding Sequence | HYDRAULIC BRAKE SYSTEM BLEEDING (MANUAL) | ||
| Disc Brakes | DISC BRAKE COMPONENT SPECIFICATIONS | ||
| Torque | DISC BRAKE COMPONENT SPECIFICATIONS | ||
| Charging | |||
| Generator | GENERATOR USAGE | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Drive Belts | |||
| Adjustment | Serpentine Belt With Self-Adjusting Tensioner | ||
| Belt Routing | For 3.6L, see illustration under INSTALLATION PROCEDURE For 3.8L, see illustration under REPLACING DRIVE BELT (L26) . |
||
| Engine Cooling | |||
| General Service Specifications | NA | ||
| Radiator Cap Pressure | Specification is stamped on Pressure Cap | ||
| Thermostat R & I | |||
| 3.6L | N/A | ||
| 3.8L | THERMOSTAT REPLACEMENT (L26) | ||
| Water Pump R & I | |||
| 3.6L | WATER PUMP REPLACEMENT (LY7) | ||
| 3.8L | WATER PUMP REPLACEMENT (L26) | ||
| Engine Mechanical | |||
| 3.6L | |||
| Compression | No cylinder reading should be less than 965 kPa (140 psi). The lowest reading should not be less than 70 percent of the highest reading. |
||
| Oil Pressure | Oil Pressure - Minimum @ Idle 10 psi (69 kPa) Oil Pressure - Minimum @ 2,000 RPM 20 psi (138 kPa) |
||
| Overhaul | ENGINE MECHANICAL SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| 3.8L | |||
| Compression | The lowest reading should not be less than 70 percent of the highest reading. No cylinder reading should be less than 689 kPa (100 psi). |
||
| Oil pressure | Oil Pressure - @ 1850 RPM 60 psi (414 kPa) | ||
| Overhaul | ENGINE MECHANICAL SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate/Drive PlateTorque | |||
| 3.6L | First step 22 ft. lbs. (30 N.m) Final Step + an additional 45 degrees |
||
| 3.8L | First step 11 ft. lbs. (15 N.m) Final step + additional 50 degrees |
||
| Fuel System (3.6L) | |||
| Pressure Specification | Commanded on using scan tool 380-410 kPa (55-60 psi) | ||
| Fuel Pressure Test Procedure | See Fuel Pressure Gage Installation and Removal and TEST DESCRIPTION | ||
| Fuel Filter Location | The fuel filter is contained in the fuel sender (module) assembly inside the fuel tank | ||
| Fuel Filter R & I | FUEL TANK MODULE REPLACEMENT | ||
| Fuel System (3.8L) | |||
| Pressure Specification | Command on with scan tool 384-425 kPa (56-62 psi) | ||
| Fuel Pressure Test Procedure | See Fuel Pressure Gage Installation and Removal and TEST DESCRIPTION | ||
| Fuel Filter Location | The fuel filter is contained in the fuel sender assembly inside the fuel tank | ||
| Fuel Filter R & I | FUEL SENDER ASSEMBLY REPLACEMENT | ||
| Ignition | |||
| Firing Order & Cylinder Identification | |||
| 3.6L | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| 3.8L | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Spark Plug Wire resistance | 3.6L NA - Coil On Plug 3.8L 3000 ohms per ft |
||
| Ignition Wires (Routing) | |||
| 3.6L | NA - Coil On Plug | ||
| 3.8L | See illustrations under SPARK PLUG WIRE REPLACEMENT | ||
| Spark Plug | |||
| 3.6L (Type AC 41-988) | |||
| Gap (Non-Adjustable) | 0.044 in (1.10 mm) | ||
| Torque | 15 lb ft (20 N.m) | ||
| 3.8L (Type GM P/N 12568387) | |||
| Gap | 0.060 in (1.52 mm) | ||
| Torque | 11 lb ft (15 N.m) | ||
| Starting | |||
| Starter | NA | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Wheel Alignment | |||
| Adjustment Specifications | WHEEL ALIGNMENT SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 100 ft. lbs. (140 N.m) | ||