Specifications Index
ALLURE (CANADIAN) & LACROSSE SPECIFICATIONS INDEX
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | REFRIGERANT SYSTEM CAPACITIES | ||
| Torque | Automatic System see FASTENER TIGHTENING SPECIFICATIONS Manual System see FASTENER TIGHTENING SPECIFICATIONS |
||
| Axle Nut/Hub Nut | |||
| Front | (New Nut) 118 ft. lbs. (160 N.m) | ||
| Battery | BATTERY USAGE | ||
| Brakes | |||
| Bleeding Sequence | RR, LF, LR, RF. See HYDRAULIC BRAKE SYSTEM BLEEDING (MANUAL) | ||
| Disc Brakes | |||
| Service Specifications | DISC BRAKE COMPONENT SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Charging | |||
| Generator | GENERATOR USAGE | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Drive Belts | |||
| Adjustment | Serpentine drive belts are not adjustable | ||
| Drive Belt Routing | For 3.8L, See illustration under DRIVE BELT REPLACEMENT (L26) For 5.3L, See illustration under DRIVE BELT REPLACEMENT - ACCESSORY |
||
| Engine Cooling | |||
| General Service Specifications | NA | ||
| Radiator Cap Pressure | Specification is stamped on pressure cap | ||
| Thermostat R & I | |||
| 3.8L | ENGINE COOLANT THERMOSTAT REPLACEMENT (RPOS L26/L32) | ||
| 5.3L | ENGINE COOLANT THERMOSTAT REPLACEMENT (LS4) | ||
| Water Pump R & I | |||
| 3.8L | WATER PUMP REPLACEMENT (RPOS L26/L32) | ||
| 5.3L | WATER PUMP REPLACEMENT (LS4) | ||
| Engine Mechanical | |||
| 3.8L | |||
| Compression | No cylinder reading should be less than 100 psi (689 kPa). The lowest reading should not be less than 70 percent of the highest reading. See ENGINE COMPRESSION TEST |
||
| Oil Pressure | Oil Pressure - @ 1850 RPM 60 psi (414 kPa) | ||
| Overhaul | ENGINE MECHANICAL SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| 5.3L | |||
| Compression | No cylinder reading should be less than 100 psi (689 kPa). The lowest reading should not be less than 70 percent of the highest reading. ENGINE COMPRESSION TEST |
||
| Oil pressure | 6 psi (41 kPa) at 1,000 engine RPM 18 psi (124 kPa) at 2,000 engine RPM 24 psi (165 kPa) at 4,000 engine RPM |
||
| Overhaul | ENGINE MECHANICAL SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate/Drive PlateTorque | |||
| 3.8L | First Pass 11 ft. lbs. (15 N.m) Last Pass + an additional 50 degrees |
||
| 5.3L | First Pass 15 ft. lbs. (20 N.m) Second Pass 37 ft. lbs. (50 N.m) Final Pass 74 ft. lbs. (100 N.m) |
||
| Fuel System | |||
| Pressure Specification | 3.8L 50-60 psi (345-414 kPa) 5.3L 50-60 psi (345-414 kPa) |
||
| Fuel Pressure Test Procedure | 3.8L See Fuel Pressure Gage Installation and Removal
and FUEL SYSTEM DIAGNOSIS 5.3L See Fuel Pressure Gage Installation and Removal and FUEL SYSTEM DIAGNOSIS |
||
| Fuel Filter Location | 3.8L & 5.3L fuel strainer attaches to the lower end of the fuel sender (fuel pump module) in fuel tank and is not serviceable | ||
| Fuel Filter R & I | 3.8L See FUEL SENDER ASSEMBLY REPLACEMENT 5.3L See FUEL TANK FUEL PUMP MODULE REPLACEMENT |
||
| Ignition | |||
| Firing Order & Cylinder Identification | |||
| 3.8L | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| 5.3L | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires (Resistance) | 3.8L 3000 ohms per ft 5.3L 397-1,337 ohms |
||
| Ignition Wires (Routing) | |||
| 3.8L | See illustrations under SPARK PLUG WIRE REPLACEMENT | ||
| 5.3L | Spark plugs wires route directly down from coil to spark plug | ||
| Spark Plug | |||
| 3.8L (Type GM P/N 12568387) | |||
| Gap | 0.060 in (1.52 mm) | ||
| Torque | 11 lb ft (15 N.m) | ||
| 5.3L (Type GM P/N 12571164 or AC Spark Plug P/N 41-985) | |||
| Gap | 0.040 in (1.02 mm) | ||
| Torque | 11 lb ft (15 N.m) | ||
| Starting | |||
| Starter | NA | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Wheel Alignment | |||
| Adjustment Specifications | WHEEL ALIGNMENT SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 100 lb ft (140 N.m) | ||