Common Specs & Procedures Index
REGAL COMMON SPECS & PROCEDURES
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | REFRIGERANT SYSTEM SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Axle Nut/Hub Nut Front) | |||
| First Pass | 111 Ft. Lbs. (150 N.m) | ||
| Second Pass | Loosen 45 degrees | ||
| Final Pass | 184 Ft. Lbs. (250 N.m) | ||
| Battery | BATTERY USAGE | ||
| Brakes | |||
| Bleeding Sequence | RR, LR, RF, LF |
||
| Disc Brakes | |||
| Service Specifications | DISC BRAKE COMPONENT SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Charging | |||
| Generator | GENERATOR USAGE | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Drive Belts | |||
| Adjustment | |||
| 2.0L | Non-Adjustable Serpentine Belt | ||
| 2.4L | Non-Adjustable Serpentine Belt | ||
| Drive Belt Routing | |||
| 2.0L | See Graphic under DRIVE BELT REPLACEMENT | ||
| 2.4L | See graphic under DRIVE BELT REPLACEMENT (LUK) | ||
| Engine Cooling | |||
| General Service Specifications | NA | ||
| Radiator Cap Pressure | Pressure rating is shown on the pressure cap. | ||
| Thermostat R & I | |||
| 2.0L | ENGINE COOLANT THERMOSTAT REPLACEMENT (LHU) | ||
| 2.4L | ENGINE COOLANT THERMOSTAT REPLACEMENT (L4) | ||
| Water Pump R & I | |||
| 2.0L & 2.4L | WATER PUMP REPLACEMENT (L4) | ||
| Engine Mechanical | |||
| 2.0L | |||
| Compression | minimum compression in any 1 cylinder should not be less than 70 percent of the highest cylinder. No cylinder should read less than 690 kPa (100 psi). | ||
| Oil Pressure Minimum - @1000 RPM @ 90°C (194°F) |
30-70 psi (206.84-482.63 kPa) | ||
| Overhaul | ENGINE MECHANICAL SPECIFICATIONS (LDK, LHU) | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| 2.4L DOHC | |||
| Compression | minimum compression in any 1 cylinder should not be less than 70 percent of the highest cylinder. No cylinder should read less than 690 kPa (100 psi). | ||
| Oil pressure Minimum - @1000 RPM @ 90°C (194°F) |
30-70 psi (206.84-482.63 kPa) | ||
| Overhaul | ENGINE MECHANICAL SPECIFICATIONS (LAF, LEA, OR LUK) | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS (LAF, LEA, OR LUK) | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE/FLUIDS tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate/Drive Plate Torque | |||
| First Pass | 39 Ft. Lbs. (53 N.m) | ||
| Final Pass | Additional 25 Degrees | ||
| Fuel System | |||
| Pressure Specification | Key on Engine Off 50-100 psi (345-690 kPa) Engine Running 43-58 psi (300-400 kPa) |
||
| Fuel Pressure Test Procedure | |||
| 2.0L | CIRCUIT/SYSTEM VERIFICATION | ||
| 2.4L | CIRCUIT/SYSTEM VERIFICATION | ||
| Fuel Filter Location | Fuel filter is an integral part of the in-tank fuel pump module. | ||
| Fuel Filter R & I | FUEL TANK FUEL PUMP MODULE REPLACEMENT (NU6) or FUEL TANK FUEL PUMP MODULE REPLACEMENT (NT7) | ||
| Ignition | |||
| Firing Order & Cylinder Identification | |||
| 2.0L & 2.4L | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires (Resistance) | Engines have coil-on-plug ignition. | ||
| Ignition Wires (Routing) | Engines have coil-on-plug ignition. | ||
| Spark Plug | |||
| 2.0L (Type = Refer to Electronic Parts Catalog) | |||
| Gap | 0.030-0.035 In. (0.75-0.90 mm) | ||
| Torque | 15 Ft. Lbs. (20 N.m) | ||
| 2.4L (Type = Refer to Electronic Parts Catalog) | |||
| Gap | 0.030-0.035 In. (0.75-0.90 mm) | ||
| Torque | 15 Ft. Lbs. (20 N.m) | ||
| Starting | |||
| Starter | NA non-repairable starter motor | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Wheel Alignment | |||
| Adjustment Specifications | WHEEL ALIGNMENT SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 110 Ft. Lbs. (150 N.m). See Wheel Nut Tightening Sequence illustration under INSTALLATION PROCEDURE | ||