Common Specs & Procedures Index
ENVISION COMMON SPECS & PROCEDURES
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | APPROXIMATE FLUID CAPACITIES | ||
| Torque | FASTENER SPECIFICATIONS | ||
| Axle/Wheel Drive Shaft Nut (Replace with New Nut) | |||
| Tighten | First Pass 150 N.m (111 lb. ft.) Second Pass Release 45 degrees Final Pass 250 N.m (184 lb ft) |
||
| Battery | NA | ||
| Brakes | |||
| Bleeding Sequence | RIGHT REAR, LEFT FRONT, LEFT REAR, RIGHT FRONT HYDRAULIC BRAKE SYSTEM BLEEDING (MANUAL) HYDRAULIC BRAKE SYSTEM BLEEDING (PRESSURE) |
||
| Disc Brakes | |||
| Service Specifications | DISC BRAKE COMPONENT SPECIFICATIONS | ||
| Torque | FASTENER SPECIFICATIONS | ||
| Charging | |||
| Generator | NA | ||
| Torque | FASTENER SPECIFICATIONS | ||
| Drive Belts | |||
| Adjustment | Non-Adjustable Serpentine Belt | ||
| Drive Belt Routing | See the figure under 2.0L DRIVE BELT REPLACEMENT | ||
| Engine Cooling | |||
| General Service Specifications | N/A | ||
| Radiator Cap Pressure | Pressure Stamped On Cap | ||
| Thermostat R & I | |||
| 2.0L | ENGINE COOLANT THERMOSTAT HOUSING REPLACEMENT | ||
| Water Pump R & I | |||
| 2.0L | 2.0L WATER PUMP REPLACEMENT | ||
| Engine Mechanical | |||
| 2.0L | |||
| Compression | ENGINE COMPRESSION TEST | ||
| Oil Pressure | 2.0L Minimum - @700 RPM @100°C - 140-200 kPa (20-29 psi) | ||
| Overhaul | 2.0L ENGINE MECHANICAL SPECIFICATIONS | ||
| Torque | 2.0L FASTENER SPECIFICATIONS | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE/FLUIDS tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate/Drive Plate Torque - 2.0L | Flywheel First Pass - 30 N.m (22 lb ft) Final Pass - additional 80 degrees Flexplate First Pass - 20 N.m (15 lb ft) Second Pass - 30 N.m (22 lb ft) Final Pass - additional 40 degrees |
||
| Fuel System | |||
| Pressure Specification - 2.0L | Ignition ON, Engine OFF - 345-650 kPa (50-94 psi) | ||
| Fuel Pressure Test Procedure - 2.0L, | CIRCUIT/SYSTEM VERIFICATION | ||
| Fuel Filter Location - 2.0L | Fuel Filter is Part of the Fuel Tank Fuel Pump Module | ||
| Fuel Filter R & I - 2.0L | FUEL TANK FUEL PUMP MODULE REPLACEMENT | ||
| Ignition | |||
| Firing Order & Cylinder Identification | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires (Resistance) | Coil On Plug | ||
| Ignition Wires (Routing) | |||
| 2.0L | Coil On Plug | ||
| Spark Plug | |||
| 2.0L See Parts Catalog for Application | |||
| Gap | 0.95-1.10 mm (0.037-0.043 in ) | ||
| Torque | 20 N.m (15 lb ft) | ||
| Starting | |||
| Starter | N/A | ||
| Torque | FASTENER SPECIFICATIONS | ||
| Wheel Alignment | |||
| Adjustment Specifications | WHEEL ALIGNMENT SPECIFICATIONS | ||
| Torque | FASTENER SPECIFICATIONS | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 150 N.m (111 lb ft) For Tightening Sequence, Please see the Figure Under INSTALLATION PROCEDURE |
||