LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Buick >> 2017 >> Verano Base, Gas/Ethanol >> Repair and Diagnosis >> Accessories & Equipment >> Collision/Avoidance >> Object Detection System And Pedestrian Protection System >> Diagnostic Information and Procedures >> Lane Departure Warning System Malfunction >> Circuit/System Testing
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Circuit/System Testing

Lane Departure Warning Switch Circuit Malfunction

  1. Ignition OFF, disconnect the harness connector at the S48A Multifunction Switch - Instrument Panel. It may take up to 2 minutes for all vehicle systems to power down.
  2. Test for less than 10 Ω between the ground circuit terminal 7 and ground.
    • If 10 Ω or greater 
    1. Ignition OFF.
    2. Test for less than 2 Ω in the ground circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the ground circuit.
      • If less than 2 Ω, repair the open/high resistance in the ground connection.
    • If less than 10 Ω 
  3. Ignition ON.
  4. Verify the scan tool Lane Departure Warning Switch parameter is Off.
    • If not Off 
    1. Ignition OFF, disconnect the harness connector at the K109 Frontview Camera Module.
    2. Test for infinite resistance between the S48A Multifunction Switch - Instrument Panel signal circuit terminal 6 and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance, replace the K109 Frontview Camera Module.
    • If Off 
  5. Install a 3 A fused jumper wire between the signal circuit terminal 6 and ground.
    NOTE:

    The next step must be completed with in 8 s. If not tested within 8 s, the parameter will change back to Open and DTC B356A will set.

  6. Verify the scan tool Lane Departure Warning Switch parameter is Closed.
    • If not On 
    1. Ignition OFF, disconnect the harness connector at the K109 Frontview Camera Module, ignition ON.
    2. Test for less than 1 V between the signal circuit and ground.
      • If 1 V or greater, repair the short to voltage on the circuit.
      • If less than 1 V
    3. Test for less than 2 Ω in the signal circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the K109 Frontview Camera Module.
    • If On 
  7. Test or replace the S48A Multifunction Switch - Instrument Panel.

Lane Departure Warning Switch Indicator Circuit Malfunction

  1. Ignition OFF, disconnect the harness connector at the S48A Multifunction Switch - Instrument Panel, ignition ON.
    2. NOTE:

    Verify interior lighting dimming is turned all the way up.

  2. Test for 6.2 - 10.9 V between the dimming control circuit terminal 12 and ground.
    • If less than 6.2 V 
    1. Ignition OFF, disconnect the X1 harness connector at the K9 Body Control Module.
    2. Test for infinite resistance between the control circuit and ground.
      • If less than infinite resistance, repair the short to ground in the circuit.
      • If infinite resistance
    3. Test for less than 2 Ω in the control circuit end to end.
    • If greater than 10.9 V 
    1. Ignition OFF, disconnect the X1 harness connector at the K9 Body Control Module, ignition ON.
    2. Test for less than 1 V between the control circuit and ground.
    • If between 6.2 - 10.9 V 
  3. Connect a test lamp between the control circuit terminal 11 and B+.
  4. Verify the test lamp turns ON and OFF when Commanding the Lane Departure Warning Indicator ON and OFF with a scan tool.
    • If the test lamp is always OFF 
    1. Ignition OFF, disconnect the harness connector at the K109 Frontview Camera Module, ignition ON.
    2. Test for less than 1 V between the control circuit and ground.
      • If 1 V or greater, repair the short to voltage on the circuit.
      • If less than 1 V
    3. Ignition OFF.
    4. Test for less than 2 Ω in the control circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the S48A Multifunction Switch - Instrument Panel.
    • If the test lamp is always ON 
    1. Ignition OFF, disconnect the harness connector at the K109 Frontview Camera Module.
    2. Test for infinite resistance between the control circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance, replace the K109 Frontview Camera Module.
    • If the test lamp turns ON and OFF 
  5. Test or replace the S48A Multifunction Switch - Instrument Panel.
scientia non olet · About LEMON Manuals