LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Cadillac >> 2003 >> Escalade EXT >> Repair and Diagnosis >> External Pages >> Different car >> Section 618 (Body Control System) >> Diagnostic Information and Procedures >> Power Mode Mismatch >> Test Description
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Test Description

WARNING: This page is about a different car, the 2004 Cadillac CTS. However, it is still accessible from the selected car via links, so may be relevant.

The numbers below refer to the step numbers on the diagnostic table.

  1. 2:  This step tests for proper circuit operation to permit communications.
  2. 7:  This step tests for battery voltage on the signal circuits that are not required.
  3. 8:  This step tests for no battery voltage on the required signal circuits.
  4. 9:  If any ignition switch parameters that should be inactive in the present ignition switch position are active, 2 ignition switch signal circuits may be shorted together.
  5. 10:  This step eliminates open circuits as the cause of the malfunction.
Power Mode Mismatch

Step Action Yes No
Schematic Reference:  Body Control System Schematics  
Connector End View Reference:  Body Control System Connector End Views  
1
  1. Install a scan tool.
  2. Turn ON the ignition.
  3. Attempt to communicate with the power mode master (PMM).
Does the scan tool communicate with the PMM?		 Go to Step 3  Go to Step 2 
2  Test the following circuits of the PMM for an open:
  • The battery positive voltage circuits
  • The class 2 serial data circuits
  • The ground circuits

Did you find and correct the condition?		 Go to Step 3  Go to Step 12 
3
IMPORTANT: Open the driver door and leave it open during this test. This will disable the retained accessory power (RAP) power mode and eliminate this power mode from the power mode parameter list.
  1. Install a scan tool.
  2. Turn OFF the ignition.
  3. With a scan tool, under the Diagnostic Circuit Check menu observe the Class 2 Power Mode parameter.
Does the displayed power mode parameter match the actual ignition switch position?		 Go to Step 4  Go to Step 7 
4
  1. Turn ON the ignition, with the engine OFF.
  2. With a scan tool, under the Diagnostic Circuit Check menu observe the Class 2 Power Mode parameter.
Does the displayed power mode parameter match the actual ignition switch position?		 Go to Step 5  Go to Step 7 
5
IMPORTANT: The engine may start during this procedure. Turn the ignition OFF after verifying this power mode.
  1. Turn the ignition switch to the CRANK position.
  2. With a scan tool, under the Diagnostic Circuit Check menu observe the Class 2 Power Mode parameter.
Does the displayed power mode parameter match the actual ignition switch position?		 Go to Step 6  Go to Step 7 
6
  1. Turn the ignition switch to the ACCY position.
  2. With a scan tool, under the Diagnostic Circuit Check menu observe the Class 2 Power Mode parameter.
Does the displayed power mode parameter match the actual ignition switch position?		 Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems Go to Step 7 
7 
IMPORTANT: The engine may start during this procedure. Turn the ignition OFF after verifying this power mode.
  1. Turn OFF the ignition.
  2. Disconnect the PMM.
  3. Hold the ignition switch in the position that indicated the incorrect power mode.
  4. With a test lamp attached to a good ground, test the PMM ignition switch inputs for voltage. Refer to Body Control System Description and Operation .
Is voltage present on only the inputs specified for the ignition switch position?		 Go to Step 8  Go to Step 9 
8 
IMPORTANT: The engine may start during this procedure. Turn the ignition OFF after verifying this power mode.
  1. Hold the ignition switch in the position that indicated the incorrect power mode.
  2. With a test lamp attached to a good ground, test the PMM ignition switch inputs for voltage. Refer to Body Control System Description and Operation .
Is voltage not present on any inputs specified for the ignition switch position?		 Go to Step 10  Go to Step 12 
9 
  1. Disconnect the ignition switch.
  2. Test the PMM ignition switch input circuits for a short to voltage. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
  3. Test the PMM ignition switch circuits for a short between circuits. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?		 Go to Step 15  Go to Step 11 
10 
  1. Disconnect the ignition switch.
  2. Test the PMM ignition switch input circuits for an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?		 Go to Step 15  Go to Step 11 
11 Inspect for poor connections and terminal tension at the harness connector of the ignition switch. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?		 Go to Step 15  Go to Step 13 
12 Inspect for poor connections and terminal tension at the harness connector of the PMM. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?		 Go to Step 15  Go to Step 14 
13 Replace the ignition switch. Refer to Ignition Switch Replacement in Steering Wheel and Column.
Did you complete the replacement?		 Go to Step 15  -
14
IMPORTANT: After replacement of the PMM, perform the set up procedure if required.
Replace the PMM. Refer to Control Module References .Did you complete the replacement?		 Go to Step 15  -
15
IMPORTANT: The engine may start during this procedure. Turn the ignition OFF after verifying all power modes.
  1. Reconnect all disconnected components.
  2. With a scan tool, under the Diagnostic Circuit Check menu observe the Class 2 Power Mode parameter.
  3. Cycle the ignition switch through all possible positions one at a time.
Does the displayed power mode parameter match the actual ignition switch position?		 System OK Go to Step 1 
scientia non olet · About LEMON Manuals