LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Chevrolet >> 2002 >> Astro Van Cargo, AWD >> Repair and Diagnosis >> Electrical >> Charging Systems >> System Tests >> Test A: Charging System Test
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Test A: Charging System Test

  1. If engine electrical diagnostic system check was performed, go to next step. If engine electrical diagnostic system check was not performed, go to ENGINE ELECTRICAL DIAGNOSTIC SYSTEM CHECK .
  2. Start engine and observe charge indicator on Instrument Panel Cluster (IPC) or message in Driver Information Center (DIC). If charge indicator illuminates or DIC displays a charging system message, go to next step. If charge indicator light does not illuminate or DIC does not display a charging system message, go to TEST C: CHARGE INDICATOR LIGHT INOPERATIVE .
    3. NOTE: Green POWER light of tester should remain illuminated while tester is being used.
  3. Turn ignition switch to OFF position. Using CS Electronic Generator Tester (J-41450-B), connect Red lead to generator output terminal and Black lead to metal generator housing. If Green POWER light does not illuminate, go to next step. If Green POWER light illuminates, go to step  6.
  4. Using a DVOM, measure voltage between generator output terminal (Red wire) and generator metal housing. If battery voltage does not exist, go to next step. If battery voltage exists, go to step  14.
  5. Using a DVOM, measure voltage between generator output terminal and battery negative terminal. If battery voltage exists, go to step  12. If battery voltage does not exist, go to step  11.
    6. CAUTION: Make sure load is completely turned off before connecting or disconnecting carbon pile load tester to battery.
  6. Connect carbon pile tester to battery. Connect inductive ammeter to output circuit of generator. Disconnect generator 4-pin harness connector. Locate matching harness connector on CS electronic generator tester and connect it to generator. If Red DIAGNOSTIC light illuminates, go to next step. If Red DIAGNOSTIC light does not illuminate, go to step  13.
  7. Start engine and allow to idle for 30 seconds. Increase engine speed to 2500 RPM. If Red DIAGNOSTIC light does not illuminate, go to next step. If Red DIAGNOSTIC light illuminates, go to step  15.
  8. Maintain engine speed at 2500 RPM. Turn on load of carbon pile tester and increase load until load is 73-amps. If Red DIAGNOSTIC light does not illuminate, go to next step. If Red DIAGNOSTIC light illuminates, go to step  15.
  9. Maintain engine speed at 2500 RPM and continue to operate generator at load test value. Using a DVOM, measure voltage drop between generator output terminal (Red wire) and positive battery terminal. If voltage drop is less than 0.5 volt, go to next step. If voltage drop is 0.5 volt or more, go to step  11.
  10. Maintain engine speed at 2500 RPM and continue to operate generator at load test value. Using a DVOM, measure voltage drop between generator metal housing and negative battery terminal. If voltage drop is less than 0.5 volt, go to step  16. If voltage drop is 0.5 volt or more, go to step  12.
  11. Repair high resistance or open in generator output circuit. See WIRING DIAGRAMS . After repairs are made, go to step  16.
  12. Repair high resistance or open in ground circuit of generator. See WIRING DIAGRAMS . After repairs are made, go to step  16.
  13. Disconnect CS electronic generator tester harness connector from generator, but leave alligator clips connected so Green POWER light remains illuminated. Connect a jumper wire with an in-line 100-ohm resister between the CS electronic generator tester harness connector terminal "B" and a good ground. If Red DIAGNOSTIC light does not illuminate, go to next step. If Red DIAGNOSTIC light illuminates, go to step  15.
  14. There is a problem with the CS electronic generator tester. Refer to manufacturers instructions, how to test the CS electronic generator tester for proper operation. Repair or replace tester, then go to step  3.
  15. Replace generator. See GENERATOR . After repairs are made, go to next step.
  16. Retest system to verify repair. If condition was found and corrected, system is okay. If condition was not found, go to step  2.
scientia non olet · About LEMON Manuals