Specifications Index
COBALT SPECIFICATIONS INDEX
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | REFRIGERANT SYSTEM CAPACITIES | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Axle Nut/Hub Nut | |||
| Front | 155 ft. lbs. (210 N.m) | ||
| Battery | BATTERY USAGE | ||
| Brakes | |||
| Bleeding Sequence | RR-LF-LR-RF. See HYDRAULIC BRAKE SYSTEM BLEEDING (MANUAL) | ||
| Disc Brakes | DISC BRAKE COMPONENT SPECIFICATIONS FASTENER TIGHTENING SPECIFICATIONS |
||
| Drum Brakes | DRUM BRAKE COMPONENT SPECIFICATIONS FASTENER TIGHTENING SPECIFICATIONS |
||
| Charging | |||
| Generator | GENERATOR USAGE | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Drive Belts | |||
| Adjustment | Serpentine drive belts are not adjustable | ||
| Belt Routing | See illustration for 2.0L DRIVE BELT REPLACEMENT See illustration for 2.2L DRIVE BELT REPLACEMENT See illustration for 2.4L DRIVE BELT REPLACEMENT |
||
| Engine Cooling | |||
| General Service Specifications | NA | ||
| Radiator Cap Pressure | Specification is stamped on cap | ||
| Thermostat R & I | |||
| 2.0L | THERMOSTAT HOUSING REPLACEMENT (RPO LSJ) | ||
| 2.2L | THERMOSTAT HOUSING REPLACEMENT (RPO L61) | ||
| 2.4L | THERMOSTAT HOUSING REPLACEMENT (RPO LE5) | ||
| Water Pump R & I | |||
| 2.0L, 2.2L & 2.4L | WATER PUMP REPLACEMENT | ||
| Engine Mechanical | |||
| 2.0L | |||
| Compression | No cylinder reading should be less than 100 psi (689 kPa). The lowest reading cylinder should not be less than 70 percent of the highest. See ENGINE COMPRESSION TEST |
||
| Oil Pressure | Minimum - @1000 RPM 50-80 psi (344.75-551.60 kPa) | ||
| Overhaul | ENGINE MECHANICAL SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| 2.2L | |||
| Compression | No cylinder reading should be less than 100 psi (689 kPa). The lowest reading cylinder should not be less than 70 percent of the highest. See ENGINE COMPRESSION TEST |
||
| Oil Pressure | Minimum - @1000 RPM 50-80 psi (344.75-551.60 kPa) | ||
| Overhaul | ENGINE MECHANICAL SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| 2.4L | |||
| Compression | No cylinder reading should be less than 100 psi (689 kPa). The lowest reading cylinder should not be less than 70 percent of the highest. See ENGINE COMPRESSION TEST |
||
| Oil pressure | Minimum - @1000 RPM 50-80 psi (344.75-551.60 kPa) | ||
| Overhaul | ENGINE MECHANICAL SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate/Drive PlateTorque | |||
| 2.0L, 2.2L & 2.4L | |||
| First Step | 39 ft. lbs. (53 N.m) | ||
| Final Step | + an additional 25 degrees | ||
| Fuel System | |||
| Pressure Specification | |||
| 2.0L, 2.2L & 2.4L | 50-60 psi (345-414 kPa) | ||
| Fuel Pressure Test Procedure | 2.0L See Fuel Pressure Gage Installation and Removal
and FUEL SYSTEM DIAGNOSIS 2.2L See Fuel Pressure Gage Installation and Removal and FUEL SYSTEM DIAGNOSIS 2.4L See Fuel Pressure Gage Installation and Removal and FUEL SYSTEM DIAGNOSIS |
||
| Fuel Filter Location | 2.0L The in-line fuel filter is located on the fuel feed pipe between the fuel pump and the fuel injectors. Fuel strainer attaches to the lower end of the fuel pump module in the fuel tank. 2.2L The in-line fuel filter is located on the fuel feed pipe between the fuel pump and the fuel injectors. Fuel strainer attaches to the lower end of the fuel pump module in the fuel tank. 2.4L The in-line fuel filter is located on the fuel feed pipe between the fuel pump and the fuel injectors. Fuel strainer attaches to the lower end of the fuel pump module in the fuel tank. |
||
| Fuel Filter R & I | 2.0L See FUEL FILTER REPLACEMENT
and for strainer, see FUEL PUMP MODULE REPLACEMENT 2.2L See 2007 FUEL FILTER REPLACEMENT (RPO NT7) for strainer see FUEL PUMP MODULE REPLACEMENT 2.4L FUEL FILTER REPLACEMENT for strainer, see FUEL PUMP MODULE REPLACEMENT |
||
| Ignition | |||
| Firing Order & Cylinder Identification | |||
| 2.0L, 2.2L & 2.4L | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires (Resistance) All applications | coil on plug | ||
| Ignition Wires (Routing) | |||
| 2.0L, 2.2L & 2.4L | coil on plug | ||
| Spark Plug | |||
| 2.0L (Type = NA) | |||
| Gap | 0.40 in (1.0 mm) | ||
| Torque | 12.5-17 lb ft (17-23 N.m ) | ||
| 2.2L & 2.4L (Type NA) | |||
| Gap | 0.043-0.037 in (1.1-0.95 mm) | ||
| Torque | 15 lb ft (20 N.m) | ||
| Starting | |||
| Starter | NA | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Wheel Alignment | |||
| Adjustment Specifications | WHEEL ALIGNMENT SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 100 ft. lbs. (140 N.m) | ||