Specifications Index
HHR SPECIFICATIONS INDEX
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | REFRIGERANT SYSTEM CAPACITIES | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Axle Nut/Hub Nut | |||
| Front | 155 lb ft (210 N.m) | ||
| Battery | BATTERY USAGE | ||
| Brakes | |||
| Bleeding Sequence | RR-LF-LR-RF. See HYDRAULIC BRAKE SYSTEM BLEEDING (MANUAL) | ||
| Disc Brakes | DISC BRAKE COMPONENT SPECIFICATIONS FASTENER TIGHTENING SPECIFICATIONS |
||
| Drum Brakes | DRUM BRAKE COM PONENT SPECIFICATIONS FASTENER TIGHTENING SPECIFICATIONS |
||
| Charging | |||
| Generator | GENERATOR USAGE | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Drive Belts | |||
| Adjustment | Serpentine drive belts are not adjustable | ||
| Belt Routing | 2.2L DRIVE BELT REPLACEMENT 2.4L DRIVE BELT REPLACEMENT |
||
| Engine Cooling | |||
| General Service Specifications | NA | ||
| Radiator Cap Pressure | Specification is stamped on pressure cap | ||
| Thermostat R & I | |||
| 2.2L | See THERMOSTAT REPLACEMENT (RPO L61) | ||
| 2.4L | See THERMOSTAT REPLACEMENT (RPO LE5) | ||
| Water Pump R & I | |||
| 2.2L & 2.4L | See WATER PUMP REPLACEMENT | ||
| Engine Mechanical | |||
| 2.2L | |||
| Compression | No cylinder reading should be less than 100 psi (689 kPa). The lowest reading cylinder should not be less than 70 percent of the highest. See ENGINE COMPRESSION TEST |
||
| Oil Pressure | Oil Pressure - Minimum - @1000 RPM 50-80 psi (344.75-551.60 kPa) | ||
| Overhaul | ENGINE MECHANICAL SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| 2.4L | |||
| Compression | No cylinder reading should be less than 100 psi (689 kPa). The lowest reading cylinder should not be less than 70 percent of the highest. ENGINE COMPRESSION TEST |
||
| Oil pressure | Oil Pressure - Minimum - @1000 RPM 50-80 psi (344.75-551.60 kPa) | ||
| Overhaul | ENGINE MECHANICAL SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate/Drive PlateTorque 2.2L & 2.4L (A/T & M/T) | 39 ft. lbs. (53 N.m) + an additional 25 degrees |
||
| Fuel System | |||
| Pressure Specification | 2.2L 50-60 psi (345-414 kPa) 2.4L 50 psi (345 kPa) |
||
| Fuel Pressure Test Procedure | 2.2.L See Fuel Pressure Gage Installation and Removal
and FUEL SYSTEM DIAGNOSIS 2.4L See Fuel Pressure Gage Installation and Removal and FUEL SYSTEM DIAGNOSIS |
||
| Fuel Filter Location | 2.2L & 2.4L Fuel strainer is located on Fuel Pump Module inside fuel tank. | ||
| Fuel Filter R & I | 2.2L See FUEL PUMP MODULE REPLACEMENT 2.4L See FUEL PUMP MODULE REPLACEMENT |
||
| Ignition | |||
| Firing Order & Cylindere Identification | |||
| 2.2L | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| 2.4L | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires (Resistance) | 2.2L & 2.4L Coil on plug | ||
| Ignition Wires (Routing) | |||
| 2.2L & 2.4L | Coil on plug | ||
| Spark Plug | |||
| 2.2L (Type GM P/N 12569190 or A/C/ DELCO P/N 41-981) | |||
| Gap | 0.043 in (1.08 mm) | ||
| Torque | 15 lb ft (20 N.m) | ||
| 2.4L (Type GM P/N 12569190 or AC 41-981) | |||
| Gap | 0.042 in (1.06 mm) | ||
| Torque | 15 lb ft (20 N.m) | ||
| Starting | |||
| Starter | NA | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Wheel Alignment | |||
| Adjustment Specifications | WHEEL ALIGNMENT SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 100 ft. lbs. (140 N.m) | ||