LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Chevrolet >> 2006 >> SSR Automatic >> Repair and Diagnosis >> External Pages >> Different car >> Section 104 (Anti-Lock Brake System, Traction Control System & Stability Control System) >> Repair Instructions >> Brake Pressure Modulator Valve Replacement >> Installation Procedure
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Installation Procedure

WARNING: This page is about a different car, the 2007 Chevrolet Corvette. However, it is still accessible from the selected car via links, so may be relevant.
    IMPORTANT: When installing a new BPMV, do NOT remove the shipping plugs from the outlets until after installation into the vehicle.
    Fig 1: View Of EBCM, BPMV & Bolts
    GM143452Courtesy of GENERAL MOTORS CORP.
  1. Clean the BPMV seal surface with alcohol using a clean rag.
  2. Install the seal to the BPMV, if it is not cut or damaged.
  3. Install the EBCM to the BPMV.
    4. NOTE: Refer to Fastener Notice .
  4. Install the 4 EBCM-to-BPMV retaining bolts. Tighten in a criss-cross pattern.

    Tighten: 

    • First pass: Tighten the bolts to 3 N.m (27 lb in).
    • Second pass: Tighten the bolts to 6 N.m (53 lb in).
  5. Install the EBCM/BPMV insulator mounting bolt.

    Tighten:  Tighten the bolt to 14 N.m (10 lb ft).

    6. Fig 2: EBCM Harness Connector & Bracket
    GM707000Courtesy of GENERAL MOTORS CORP.
  6. Install the EBCM/BPMV into the bracket on the vehicle.
  7. Install the two insulator nuts (1).

    Tighten:  Tighten the to 12 N.m (106 lb in).

  8. Connect the brake fluid pressure sensor electrical connector (2).
    9. Fig 3: Brake Pipes At BPMV To Rear Brake Calipers
    GM705585Courtesy of GENERAL MOTORS CORP.
  9. Install the brake pipes from the rear brake calipers (1, 2) to the BPMV in the same location as removed.

    Tighten:  Tighten the brake pipe fittings to 16 N.m (12 lb ft).

    10. Fig 4: Brake Pipes At BPMV To Front Brake Calipers
    GM705580Courtesy of GENERAL MOTORS CORP.
  10. Install the brake pipes from the front brake calipers (1, 2) to the BPMV in the same location as removed.

    Tighten:  Tighten the brake pipe fittings to 16 N.m (12 lb ft).

    11. Fig 5: Brake Pipes To Master Cylinder
    GM705577Courtesy of GENERAL MOTORS CORP.
  11. Install the brake pipes from the master cylinder (1, 2) to the BPMV in the same location as removed.

    Tighten:  Tighten the brake pipe fittings to 16 N.m (12 lb ft).

  12. Connect the BPMV pump motor ground.
  13. Connect the EBCM harness connector.
    IMPORTANT: Both sides of the EBCM harness connector must be engaged with lever before closing.
  14. Install the power steering fluid reservoir and bracket. Refer to Remote Power Steering Fluid Reservoir Replacement .
  15. Fill and bleed the hydraulic brake system. Refer to Master Cylinder Reservoir Filling and Hydraulic Brake System Bleeding (Manual) or Hydraulic Brake System Bleeding (Pressure) .
  16. Perform the Automated Bleed Procedure. Refer to Antilock Brake System Automated Bleed Procedure .
  17. Perform the Symptoms - Antilock Brake System .
scientia non olet · About LEMON Manuals