Specifications Index
MONTANA SV6, TERRAZA & UPLANDER SPECIFICATIONS INDEX
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | REFRIGERANT SYSTEM CAPACITIES | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Axle Nut/Hub Nut | |||
| Front | 118 ft. lbs. (160 N.m) | ||
| Rear | 192 ft. lbs. (260 N.m) | ||
| Battery | BATTERY USAGE | ||
| Brakes | |||
| Bleeding Sequence | HYDRAULIC BRAKE SYSTEM BLEEDING (MANUAL) | ||
| Disc Brakes | DISC BRAKE COMPONENT SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Charging | |||
| Generator | GENERATOR USAGE | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Drive Belts | |||
| Adjustment | Serpentine Drive Belts Are Not Adjustable | ||
| Belt Routing | 3.5L See drive belt routing illustration under INSTALLATION PROCEDURE 3.9L See drive belt routing illustration under INSTALLATION PROCEDURE |
||
| Engine Cooling | |||
| General Service Specifications | NA | ||
| Radiator Cap Pressure | Specification is stamped on pressure cap | ||
| Thermostat R & I | |||
| 3.5L | THERMOSTAT HOUSING REPLACEMENT - LX9 (3.5L) | ||
| 3.9L | THERMOSTAT REPLACEMENT - LZ9 (3.9L) | ||
| Water Pump R & I | |||
| 3.5L | WATER PUMP REPLACEMENT - LX9 (3.5L) | ||
| 3.9L | WATER PUMP REPLACEMENT - LZ9 (3.9L) | ||
| Engine Mechanical | |||
| 3.5L | |||
| Compression | No cylinder reading should be less than 100 psi (689 kPa). The lowest reading should not be less than 70 percent of the highest reading. See ENGINE COMPRESSION TEST |
||
| Oil Pressure | Oil Pressure - @ 1850 RPM 30-45 psi (207-310 kPa) | ||
| Overhaul | ENGINE MECHANICAL SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| 3.9L | |||
| Compression | No cylinder reading should be less than 100 psi (689 kPa) The lowest reading should not be less than 70 percent of the highest reading. See ENGINE COMPRESSION TEST |
||
| Oil pressure | Oil Pressure - @ 1850 RPM 30-45 psi (207-310 kPa) | ||
| Overhaul | ENGINE MECHANICAL SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate/Drive PlateTorque | 3.5L & 3.9L 52 ft. lbs. (70 N.m) | ||
| Fuel System | |||
| Pressure Specification | 3.5L & 3.9L 50-60 psi (345-414 kPa). | ||
| Fuel Pressure Test Procedure | 3.5L See Fuel Pressure Gage Installation and Removal
and FUEL SYSTEM DIAGNOSIS 3.9L See FUEL SYSTEM DIAGNOSIS |
||
| Fuel Filter Location | 3.5L & 3.9L fuel strainer attaches to the lower end of the fuel sender in fuel tank | ||
| Fuel Filter R & I | 3.5L FUEL SENDER ASSEMBLY REPLACEMENT (SHORT WHEEL BASE)
or FUEL SENDER ASSEMBLY REPLACEMENT (LONG WHEEL BASE) 3.9L FUEL TANK MODULE REPLACEMENT (SHORT WHEEL BASE) or FUEL TANK MODULE REPLACEMENT (LONG WHEEL BASE) |
||
| Ignition | |||
| Firing Order & Cylinder Identification | |||
| 3.5L & 3.9L | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires (Resistance) | 3.5L & 3.9L 4,018 Ω per meter (1,225 Ω per ft) | ||
| Ignition Wires (Routing) | |||
| 3.5L | See illustrations under SPARK PLUG WIRE REPLACEMENT | ||
| 3.9L | See illustrations under SPARK PLUG WIRE REPLACEMENT | ||
| Spark Plug | |||
| 3.5L (Type = GM P/N 12568387 or AC Delco #41-101) | |||
| Gap | 0.060 in (1.52 mm) | ||
| Torque | 11 lb ft (15 N.m) | ||
| 3.9L (Type = GM P/N 12591131 or AC Delco #41-100) | |||
| Gap | 0.040 in (1.02 mm) | ||
| Torque | 11 lb ft (15 N.m) | ||
| Starting | |||
| Starter | NA | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Wheel Alignment | |||
| Adjustment Specifications | WHEEL ALIGNMENT SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 100 lb ft (140 N.m) | ||