Electronic Brake Control Module Scan Tool Information
WARNING: This page is about a different car, the 2010 Saturn Sky and 2010 Pontiac Solstice. However, it is still accessible from the selected car via links, so may be relevant.
Electronic Brake Control Module Scan Tool Data Parameters
| Parameter | Expected Value | Definition |
|---|---|---|
| Operating Conditions: Ignition ON | ||
| ABS Active | No | The scan tool displays Yes or No. The scan tool will display Yes when the ABS is active and No during normal vehicle operation. |
| ABS Failed | No | The scan tool displays Yes or No. The scan tool will display Yes when the ABS has failed and No during normal vehicle operation. |
| Battery Voltage Signal | Varies | This displays Volts. This is the current Battery voltage signal. |
| Brake Fluid Level Status | OK | The scan tool displays Low when the fluid is low and OK when at correct level. |
| BPP Signal | Varies | The scan tool displays Applied or Released. This is the current state of the Brake Pedal Position Sensor. |
| Brake Pressure Sensor Input | Varies | This displays Volts. This is the current brake pressure sensor voltage. |
| Delivered Torque | Varies | This displays %. This is the current percentage of torque being delivered |
| DRP Active | No | The scan tool displays Yes or No. The active status of the DRP. Indicates if DRP is currently active. |
| DRP Disabled | No | The scan tool displays Yes or No. The failed status of the DRP. Indicates if the EBCM disabled DRP due to a malfunction. |
| Engine Drag Control Failed | No | The scan tool displays Yes or No. The failed status of the Engine Drag Control Indicates if the ECM disabled Engine Drag Control due to a malfunction. |
| Lateral Accelerometer Signal | m/s 2 | The scan tool displays m/s 2 . This is the current rate of the vehicle acceleration or deceleration as reported by the lateral accelerometer sensor. |
| LF Inlet Solenoid Command | Off | The scan tool displays On or Off. This is the current state of the driver front inlet solenoid. |
| LF Outlet Solenoid Command | Off | The scan tool displays On or Off. This is the current state of the driver front outlet solenoid. |
| LF Wheel Speed Sensor | 0 km/h (0 mph) | This displays km/h (mph). This is the current vehicle speed at the driver front wheel speed sensor. |
| LR Inlet Solenoid Command | Off | The scan tool displays On or Off. This is the current state of the driver rear inlet solenoid. |
| LR Outlet Solenoid Command | Off | The scan tool displays On or Off. This is the current state of the driver rear outlet solenoid. |
| LR Wheel Speed Sensor | 0 km/h (0 mph) | This displays km/h (mph). This is the current vehicle speed at the driver rear wheel speed sensor. |
| RF Inlet Solenoid Command | Off | The scan tool displays On or Off. This is the current state of the passenger front inlet solenoid. |
| RF Outlet Solenoid Command | Off | The scan tool displays On or Off. This is the current state of the passenger front outlet solenoid. |
| RF Wheel Speed Sensor | 0 km/h (0 mph) | This displays km/h (mph). This is the current vehicle speed at the passenger front wheel speed sensor. |
| RR Inlet Solenoid Command | Off | The scan tool displays On or Off. This is the current state of the passenger rear inlet solenoid. |
| RR Outlet Solenoid Command | Off | The scan tool displays On or Off. This is the current state of the passenger rear outlet solenoid. |
| RR Wheel Speed Sensor | 0 km/h (0 mph) | This displays km/h (mph). This is the current vehicle speed at the passenger rear wheel speed sensor. |
| Panic Brake Assist Failed | No | The scan tool displays Yes or No. The failed status of the Panic Brake Assist indicates if the EBCM disabled Panic Braking due to a malfunction. |
| Pump Motor Commanded Voltage | Varies | This displays Volts. This is the current pump motor feedback voltage. |
| Requested Torque | Varies | This displays %. This is the current percentage of torque being requested. |
| Steering Position Signal | Varies | This displays °. This is the current angle of the steering position sensor. |
| TCS Active | No | The scan tool displays Yes or No. This is the state of the traction control system. |
| TCS Failed | No | The scan tool displays Yes or No. The scan tool will display Yes when the TCS has failed and No during normal vehicle operation. |
| VSES Active | Varies | The scan tool displays Yes or No. This is the state of the vehicle stability enhancement system. |
| VSES Failed | No | The scan tool displays Yes or No. The scan tool will display Yes when the VSES has failed and No during normal vehicle operation. |
| Yaw Rate Sensor Input | °/sec | The scan tool displays °/sec. The scan tool displays the signal received from the Yaw Rate sensor. |
Electronic Brake Control Module Scan Tool Output Controls
| Scan Tool Output Control | Description |
|---|---|
| Automated Bleed | This is used in order to bleed ABS hydraulics. Refer to Antilock Brake System Automated Bleed . |