LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Chevrolet >> 2009 >> Traverse LS, AWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 27 (Battery, Charging System And Starting System) >> Repair Instructions >> Battery Positive Cable Replacement >> Installation Procedure
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Installation Procedure

WARNING: This page is about a different car, the 2010 Saturn Outlook, 2010 GMC Acadia, 2010 Chevrolet Traverse, and 2010 Buick Enclave. However, it is still accessible from the selected car via links, so may be relevant.
    Fig 1: View Of Positive Battery Cable
    GM1861044Courtesy of GENERAL MOTORS CORP.
  1. Route the positive battery cable under the rear carpet and position the cable from the vehicle floor pan.
    2. Fig 2: View Of Positive Battery Cable Clips & Positive Battery Cable Cover
    GM1861043Courtesy of GENERAL MOTORS CORP.
  2. Install the positive battery cable clips (1) to the floor panel studs.
  3. Install the positive battery cable terminal to the battery positive terminal.
    4. CAUTION: Refer to Fastener Caution .
  4. Tighten the positive battery cable terminal nut.

    Tighten:  Tighten the nut to 9 N.m (80 lb in).

  5. Close the positive battery cable cover (2).
    6. Fig 3: Identifying Body Wiring Harness Connector & Negative Battery Cable Connector
    GM1860988Courtesy of GENERAL MOTORS CORP.
  6. Connect the body wiring harness electrical connector (4) to the negative battery cable electrical connector (1).
  7. Connect the body wiring harness electrical connector (3) to the battery current sensor (2).
    8. Fig 4: Identifying Body Wiring Harness, Electrical Connector & Positive Battery Cable Clips
    GM1861042Courtesy of GENERAL MOTORS CORP.
  8. Install the body wiring harness (1) to the positive battery cable clips (4).
  9. If equipped with RPO UE1, connect the body wiring harness electrical connector (2) to the battery cable electrical connector (3).
    10. Fig 5: View Of Positive Battery Cable
    GM1861041Courtesy of GENERAL MOTORS CORP.
  10. Install the positive battery cable (1) to the body wiring harness right front sill plate (2).
    11. Fig 6: View Of Positive Battery Cable Clip, Positive Battery Cable & Retainers
    GM1861040Courtesy of GENERAL MOTORS CORP.
  11. Push the grommet (1) through the dash panel.
  12. Install the positive battery cable (3) to the retainers (4) on the body wiring harness.
  13. Install the positive battery cable clip (2) to the stud on the dash panel.
  14. Reposition the passenger side corner of the dash panel sound barrier.
  15. Install the passenger side carpet. Refer to Front Floor Panel Carpet Replacement - Right Side .
  16. Install the right side instrument panel insulator panel. Refer to Instrument Panel Insulator Panel Replacement - Right Side (Acadia) or Instrument Panel Insulator Panel Replacement - Right Side (Enclave) or Instrument Panel Insulator Panel Replacement - Right Side (OUTLOOK) or Instrument Panel Insulator Panel Replacement - Right Side (Traverse) .
    17. Fig 7: Identifying Accessory Wiring Junction Block Cover & Nut
    GM1861038Courtesy of GENERAL MOTORS CORP.
  17. Ensure that the positive battery cable grommet (6) is completely seated through the dash panel.
  18. Install the positive battery cable terminal (3) to the junction block stud.
  19. Install the accessory wiring junction block nut (2).

    Tighten:  Tighten the nut to 22 N.m (16 lb ft).

  20. Close the accessory wiring junction block cover (1).
  21. Install the positive battery cable clip (5) to the multiuse relay bracket.
  22. Install the fuel injector sight shield. Refer to FUEL INJECTOR SIGHT SHIELD REPLACEMENT .
  23. Connect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection .
scientia non olet · About LEMON Manuals