Common Specs & Procedures Index
ACADIA, ENCLAVE AND TRAVERSE COMMON SPECS & PROCEDURES
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | REFRIGERANT SYSTEM SPECIFICATIONS | ||
| Torque | Automatic System FASTENER TIGHTENING SPECIFICATIONS Manual System FASTENER TIGHTENING SPECIFICATIONS |
||
| Axle Nut/Hub Nut | |||
| Front | 173 ft lb (235 N.m) | ||
| Rear | 151 ft lb (205 N.m) | ||
| Battery | BATTERY USAGE | ||
| Brakes | |||
| Bleeding Sequence | RR, LR, RF, LF. See HYDRAULIC BRAKE SYSTEM BLEEDING (MANUAL) | ||
| Disc Brakes | |||
| Service Specifications | DISC BRAKE COMPONENT SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Charging | |||
| Generator | GENERATOR USAGE | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Drive Belts | |||
| Adjustment | Non-Adjustable Serpentine Belt | ||
| Drive Belt Routing | See illustration under DRIVE BELT REPLACEMENT | ||
| Engine Cooling | |||
| General Service Specifications | N/A | ||
| Radiator Cap Pressure | Pressure is stamped on pressure cap | ||
| Thermostat R & I | |||
| 3.6L | ENGINE COOLANT THERMOSTAT REPLACEMENT | ||
| Water Pump R & I | |||
| 3.6L | WATER PUMP REPLACEMENT | ||
| Engine Mechanical | |||
| 3.6L | |||
| Compression | No cylinder reading should be less than 965 kPa (140 psi). Lowest reading should not be less than 70 percent of highest reading. See ENGINE COMPRESSION TEST | ||
| Oil Pressure | Oil Pressure - Minimum @ Idle 10 psi (69 kPa) Oil Pressure - Minimum @ 2,000 RPM 20 psi (138 kPa) |
||
| Overhaul | ENGINE MECHANICAL SPECIFICATIONS | ||
| Torque | FASTENER SPECIFICATIONS | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE/FLUIDS tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate/Drive Plate Torque | First Pass 22 ft lb (30 N.m) Final Pass an additional 45 degrees |
||
| Fuel System | |||
| Pressure Specification | Ignition ON, engine OFF, fuel pump ON with a scan tool. Fuel pressure 345-690 kPa (50-100 psi) Engine idling at normal operating temperature, Fuel Pump Flow Control Module Fuel Pressure Sensor parameter should read 300-400 kPa (43-58 psi) |
||
| Fuel Pressure Test Procedure | CIRCUIT/SYSTEM VERIFICATION | ||
| Fuel Filter Location | Fuel filter is contained in fuel sender assembly (fuel tank module) inside the fuel tank. | ||
| Fuel Filter R & I | FUEL TANK MODULE REPLACEMENT | ||
| Ignition | |||
| Firing Order & Cylinder Identification | |||
| 3.6L | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires (Resistance) | Coil On Plug | ||
| Ignition Wires (Routing) | Coil On Plug | ||
| Spark Plug | |||
| 3.6L (Type = Refer to Electronic Parts Catalogue) | |||
| Gap | 0.043 in (1.1 mm) | ||
| Torque | 15 ft lb (20 N.m) | ||
| Starting | |||
| Starter | N/A | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Wheel Alignment | |||
| Adjustment Specifications | WHEEL ALIGNMENT SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 140 ft lb (190 N.m). See nut tightening sequence under Wheel And Tire INSTALLATION PROCEDURE | ||