Common Specs & Procedures Index
CORVETTE COMMON SPECS & PROCEDURES
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | REFRIGERANT SYSTEM SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Axle Nut/Hub Nut | |||
| Front | N/A | ||
| Rear | 205 N.m (151 lb ft.) | ||
| Battery | BATTERY USAGE | ||
| Brakes | |||
| Bleeding Sequence | Manual - Right Rear, Left Front, Left Rear, Right Front (see HYDRAULIC BRAKE SYSTEM BLEEDING (MANUAL)
.) Pressure - Right Rear, Left Front, Left Rear, Right Front (see HYDRAULIC BRAKE SYSTEM BLEEDING (PRESSURE) .) |
||
| Disc Brakes | |||
| Service Specifications | DISC BRAKE COMPONENT SPECIFICATIONS (JL9, J55, J56)DISC BRAKE COMPONENT SPECIFICATIONS (J57) | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Charging | |||
| Generator | GENERATOR USAGE | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Drive Belts | |||
| Adjustment | Non-Adjustable Serpentine Belt | ||
| Drive Belt Routing | See illustration under DRIVE BELT REPLACEMENT - ACCESSORY (W/O LS9) or DRIVE BELT REPLACEMENT - ACCESSORY (LS9) | ||
| Engine Cooling | |||
| General Service Specifications | N/A | ||
| Radiator Cap Pressure | Pressure Stamped On Cap | ||
| Thermostat R & I | |||
| 6.2 L Or 7.0L | ENGINE COOLANT THERMOSTAT REPLACEMENT | ||
| Water Pump R & I | |||
| 6.2 L Or 7.0L | WATER PUMP REPLACEMENT | ||
| Engine Mechanical | |||
| 6.2 L | |||
| Compression | ENGINE COMPRESSION TEST | ||
| Oil Pressure | 165 kPa @ 1,000 RPM (24 psig) @ 1,000 RPM 241 kPa @ 2,000 RPM (35 psig) @ 2,000 RPM 262 kPa @ 3,000 RPM (38 psig) @ 3,000 RPM |
||
| Overhaul | ENGINE MECHANICAL SPECIFICATIONS (6.2L LS3)ENGINE MECHANICAL SPECIFICATIONS (6.2L LS9) | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS (6.2L LS3)FASTENER TIGHTENING SPECIFICATIONS (6.2L LS9) | ||
| 7.0 L | |||
| Compression | ENGINE COMPRESSION TEST | ||
| Oil pressure | 165 kPa @ 1,000 RPM (24 psig) @ 1,000 RPM 241 kPa @ 2,000 RPM (35 psig) @ 2,000 RPM 262 kPa @ 3,000 RPM (38 psig) @ 3,000 RPM |
||
| Overhaul | ENGINE MECHANICAL SPECIFICATIONS (7.0L) | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS (7.0L LS7) | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE/FLUIDS tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate/Drive Plate Torque | 6.2 L Or 7.0L First Pass - 20 N.m (15 lb ft) Second Pass - 50 N.m (37 lb ft) Final Pass - 100 N.m (74 lb ft) |
||
| Fuel System | |||
| Pressure Specification | 6.2 L Or 7.0L - Ignition ON, Engine OFF 384-425 kPa (55-62 psi) (see CIRCUIT/SYSTEM VERIFICATION .) | ||
| Fuel Pressure Test Procedure | 6.2 L LS3 Or 7.0L FUEL SYSTEM DIAGNOSIS (LS3 OR LS7) 6.2L LS9 FUEL SYSTEM DIAGNOSIS (LS9) |
||
| Fuel Filter Location | 6.2 L Fuel Filter Is Part of the Fuel Tank Fuel Pump Module 7.0 L Fuel Filter Is Part of the Fuel Tank Fuel Pump Module |
||
| Fuel Filter R & I | 6.2L LS3 Or 7.0L FUEL TANK FUEL PUMP MODULE REPLACEMENT - LEFT SIDE (LS3, LS7) 6.2L LS9 FUEL TANK FUEL PUMP MODULE REPLACEMENT - LEFT SIDE (LS9) |
||
| Ignition | |||
| Firing Order & Cylinder Identification | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires (Resistance) | IGNITION SYSTEM SPECIFICATIONS | ||
| Ignition Wires (Routing) | |||
| 6.2 L | Coil On Plug | ||
| 7.0 L | Coil On Plug | ||
| Spark Plug | |||
| 6.2 L | |||
| Gap | 1.02 mm (0.040 in) | ||
| Torque | 15 N.m (11 lb ft) | ||
| 7.0 L | |||
| Gap | 1.02 mm (0.040 in) | ||
| Torque | 15 N.m (11 lb ft) | ||
| Starting | |||
| Starter | N/A | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Wheel Alignment | |||
| Adjustment Specifications | WHEEL ALIGNMENT SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 140 N.m (100 lb ft.) For tightening sequence, see illustration under INSTALLATION PROCEDURE | ||