Common Specifications & Procedures
CRUZE COMMON SPECIFICATIONS & PROCEDURES
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Axle Nut/Hub Nut | |||
| Front | 1st step 111 Ft. Lb. (150 N.m) 2nd step release tension 45 degrees 3rd step 184 Ft. Lb. (250 N.m) |
||
| Battery | BATTERY USAGE | ||
| Brakes | |||
| Bleeding Sequence | RR, LR, RF, LF. See HYDRAULIC BRAKE SYSTEM BLEEDING (MANUAL) | ||
| Disc Brakes | |||
| Service Specifications | DISC BRAKE COMPONENT SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Drum Brakes | |||
| Service Specifications | DRUM BRAKE COMPONENT SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Charging | |||
| Generator | GENERATOR USAGE | ||
| Torque | See FASTENER TIGHTENING SPECIFICATIONS (LUJ) Or FASTENER TIGHTENING SPECIFICATIONS (LUW) | ||
| Drive Belts | |||
| Adjustment | Serpentine drive belts are not adjustable. | ||
| Drive Belt Routing | 1.4L See illustration under DRIVE BELT REPLACEMENT 1.8L See illustration under DRIVE BELT REPLACEMENT |
||
| Engine Cooling | |||
| General Service Specifications | SPECIFICATIONS | ||
| Radiator Cap Pressure | Specificaiton is stamped on pressure cap. | ||
| Thermostat R & I | |||
| 1.4L | ENGINE COOLANT THERMOSTAT HOUSING REPLACEMENT (LUJ) | ||
| 1.8L | ENGINE COOLANT THERMOSTAT REPLACEMENT (LUW) | ||
| Water Pump R & I | |||
| 1.4L | WATER PUMP REPLACEMENT (LUJ) | ||
| 1.8L | WATER PUMP PULLEY REPLACEMENT (LUW) | ||
| Engine Mechanical | |||
| 1.4L | |||
| Compression | Maximum pressure differential 100 kPa (14.5 psi). See ENGINE COMPRESSION TEST | ||
| Oil Pressure | At Idle 22 psi (150 kPa) At 3000 RPM 55-94 psi (380-650 kPa) |
||
| Overhaul | ENGINE MECHANICAL SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| 1.8L | |||
| Compression | Maximum pressure differential 100 kPa (14.5 psi). See ENGINE COMPRESSION TEST | ||
| Oil pressure | N/A | ||
| Overhaul | ENGINE MECHANICAL SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE/FLUIDS tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate/Drive Plate Torque | Step 1 = 44 Ft. Lb. (60 N.m) Step 2 = + 45 degrees Step 3 = + 15 degrees |
||
| Fuel System | |||
| Pressure Specification | 1.4L 36-65 PSI (250-450 kPa) 1.8L 50-60 PSI (345-414 kPa) |
||
| Fuel Pressure Test Procedure | 1.4L FUEL PRESSURE MEASUREMENT 1.8L FUEL PRESSURE MEASUREMENT |
||
| Fuel Filter Location | 1.8L The fuel strainer is attached to the lower end of the fuel pump module. | ||
| Fuel Filter R & I | 1.8L The fuel strainer is attached to the lower end of the fuel pump module and requires no maintenance. | ||
| Ignition | |||
| Firing Order & Cylinder Identification | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires (Resistance) | Engine has coil-on-plug ignition. | ||
| Ignition Wires (Routing) | Engine has coil-on-plug ignition. | ||
| Spark Plug | |||
| 1.4L (Type = Refer to Parts Catalogue) | |||
| Gap | .028 in (.70 mm) | ||
| Torque | 18 Ft. Lb. (25 N.m) | ||
| 1.8L (Type = Refer to Parts Catalogue) | |||
| Gap | .028 in (.70 mm) | ||
| Torque | 18 Ft. Lb. (25 N.m) | ||
| Starting | |||
| Starter | STARTER REPLACEMENT (LUJ) or STARTER REPLACEMENT (LUW) | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Wheel Alignment | |||
| Adjustment Specifications | WHEEL ALIGNMENT SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 100 Ft. Lb. (140 N.m) For Wheel Nut Tightening Sequence, See illustration under INSTALLATION PROCEDURE in Wheels And Tires. |
||