Common Specs & Procedures Index
(SPARK) COMMON SPECS & PROCEDURES
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | REFRIGERANT SYSTEM SPECIFICATIONS (1.2L LL0) | ||
| Torque | N/A | ||
| Axle Nut/Hub Nut | |||
| Front | 177 lb ft (240 N.m) | ||
| Rear | 140 lb ft (190 N.m) | ||
| Battery | BATTERY USAGE | ||
| Brakes | |||
| Bleeding Sequence | RR, LF, LR, RF See HYDRAULIC BRAKE SYSTEM BLEEDING (MANUAL) | ||
| Disc Brakes | |||
| Service Specifications | DISC BRAKE COMPONENT SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Drum Brakes | |||
| Service Specifications | DRUM BRAKE COMPONENT SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Charging | |||
| Generator | GENERATOR USAGE | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Drive Belts | |||
| Adjustment | Non-Adjustable Serpentine Belt | ||
| Drive Belt Routing | See routing illustration under INSTALLATION PROCEDURE | ||
| Engine Cooling | |||
| General Service Specifications | N/A | ||
| Radiator Cap Pressure | Pressure is stamped on pressure cap | ||
| Thermostat R & I | |||
| 1.2L | ENGINE COOLANT THERMOSTAT REPLACEMENT | ||
| Water Pump R & I | |||
| 1.2L | WATER PUMP REPLACEMENT | ||
| Engine Mechanical | |||
| 1.2L | |||
| Compression | ENGINE COMPRESSION TEST | ||
| Oil Pressure | idling oil temperature less than or equal to 120°C (170°F), at least 110 kPa (15.95 psi) | ||
| Overhaul | ENGINE MECHANICAL SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE/FLUIDS tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate/Drive Plate Torque | 15 lb ft + 25° (20 N.m + 25°) | ||
| Fuel System | |||
| Pressure Specification | KOEO 276-345 kPa (40-50 psi) | ||
| Fuel Pressure Test Procedure | CIRCUIT/SYSTEM VERIFICATION | ||
| Fuel Filter Location | fuel filter is contained in the fuel sender assembly inside the fuel tank | ||
| Fuel Filter R & I | FUEL LEVEL SENSOR REPLACEMENT | ||
| Ignition | |||
| Firing Order & Cylinder Identification | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires (Resistance) | Coil On Plug | ||
| Ignition Wires (Routing) | |||
| 1.2L | Coil On Plug | ||
| Spark Plug | |||
| 1.2L (Type = Refer to Electronic Parts Catalogue) | |||
| Gap | 0.8-0.9 mm (0.031-0.035 in) | ||
| Torque | 15 lb ft (20 N.m) | ||
| Starting | |||
| Starter | STARTER USAGE | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Wheel Alignment | |||
| Adjustment Specifications | WHEEL ALIGNMENT SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 140 N.m (103 lb ft) See tightening sequence illustration under INSTALLATION PROCEDURE | ||