Rear Differential Clutch Control Module Scan Tool Information
WARNING: This page is about a different car, the 2015 Chevrolet Trax and 2015 Buick Encore. However, it is still accessible from the selected car via links, so may be relevant.
Rear Differential Clutch Control Module Scan Tool Data Parameters
| Parameter | System State | Expected Value | Definition |
|---|---|---|---|
| Operating Conditions: Ignition is ON, engine OFF, vehicle stationary | |||
| All Wheel Drive | Enabled/ Disabled | Disabled | The scan tool displays Enabled when front wheel slippage occurs. |
| Base Model Part Number | - | Varies | The scan tool displays the base model part number of the module |
| Base Model Part Number Alpha Code | - | Varies | The scan tool displays the Base Model Part Number Alpha Code |
| Battery Voltage | - | Varies | The scan tool displays volts. The scan tool displays the battery voltage monitored by the module. |
| Calculated Rear Differential Clutch Speed Variation | RPM | Varies | The scan tool displays the RPM difference between the front and rear axles. |
| Date Programed | Julian Date | Varies | The scan tool displays the date the module was programed. |
| Diagnostic Data Identifier | - | - | The scan tool displays XXXX |
| End Model Part Number | - | Varies | The scan tool displays the End Model Part Number. |
| End Model Part Number Alpha Code | - | Varies | The scan tool displays the End Model Part Number Alpha Code. |
| GMLAN Identification Data - Bus 1 Type | - | Varies | The scan tool displays the GMLAN Identification Data - Bus 1 Type. |
| GMLAN Identification Data - Data Dictionary 1 Version | - | Varies | The scan tool displays the GMLAN Identification Data - Data Dictionary 1 Version. |
| GMLAN Identification Data - GMLAN Kernal1 Version | - | Varies | The scan tool displays the GMLAN Identification Data - GMLAN Kernal1 Version. |
| Left Front Wheel Speed Sensor | - | 0.0 KPH/MPH | The scan tool displays 0-160 km/h (0-99.5 mph). |
| Left Rear Wheel Speed Sensor | - | 0.0 KPH/MPH | The scan tool displays 0-160 km/h (0-99.5 mph). |
| Manufacturer Enable Counter | - | Varies | The scan tool displays the Manufacturer Enable Counter. |
| Manufacturer's Traceability Number | - | Varies | The scan tool displays the Manufacturer's Traceability Character |
| Rear Differential Actuator Estimated Torque | XX | The scan tool displays the estimated clutch torque value. | |
| Rear Differential Actuator External Control | Yes / No | No | The scan tool displays Yes when external control is requested, and No when external control is requested. |
| Rear Differential Actuator Torque Command | XX | The scan tool displays the Rear Differential Actuator commanded torque value. | |
| Rear Differential Clutch Calibration Factory Value | - | Varies | The scan tool displays the Rear Differential Clutch Calibration Factory Value. |
| Rear Differential Clutch Calibration Service Value | - | Varies | The scan tool displays the Rear Differential Clutch Calibration Service Value. |
| Rear Differential Clutch Circuit Voltage | Volts | Varies | The scan tool displays the Rear Differential Clutch Circuit Voltage. |
| Rear Differential Clutch Temperature | °C (°F) | Varies | The scan tool displays the Clutch Oil Temperature. |
| Rear Drive Clutch Status | Normal, Temporarily Disabled, Temporarily Limited, Malfunctioned | Temporarily Limited | The scan tool displays Normal/Temporarily Disabled/Temporarily Limited/Malfunctioned. |
| Rear Drive Clutch Temperature | °C (°F) | Varies | The scan tool displays the Clutch Plate Temperature. |
| Rear Electronic Limited Slip Differential External Control | Yes / No | No | The scan tool displays the command of the Rear Electronic Limited Slip Differential External Control. |
| Rear Electronic Limited Slip Differential Mode | Normal / Limited Slip | Normal | The scan tool displays if there is slip detected of the rear wheels. |
| Rear Electronic Limited Slip Differential Status | Enabled / Disabled | Enabled | The scan tool displays the Rear Electronic Limited Slip Differential Status. |
| Right Front Wheel Speed Sensor | - | 0.0 KPH/MPH | The scan tool displays 0-160 km/h (0-99.5 mph). |
| Right Rear Wheel Speed Sensor | - | 0.0 KPH/MPH | The scan tool displays 0-160 km/h (0-99.5 mph). |
| Software Module 1 Identifier | - | Varies | The scan tool displays the Software Module 1 Identifier. |
| Software Module 1 Identifier Alpha Code | - | Varies | The scan tool displays the Software Module 1 Identifier Alpha Code. |
| Software Module 2 Identifier | - | Varies | The scan tool displays the Software Module 2 Identifier |
| Software Module 2 Alpha Code | - | Varies | The scan tool displays the Software Module 2 Alpha Code |
| Subscriber ID | - | Varies | The scan tool displays the Subscriber ID. |
| System Identification | - | Varies | The scan tool displays the System Supplier ID. |
| System Name or Engine Type | - | Varies | The scan tool displays the System Name or Engine Type. |
| Vehicle Identification Number | - | Varies | The scan tool displays the Vehicle Identification Number. |
| XML Configuration Compatibility Identifier | - | Varies | The scan tool displays the XML Configuration Compatibility Identifier. |
| XML Data File Alpha Code | - | Varies | The scan tool displays the XML Data File Alpha Code. |
| XML Data File Part Number | - | Varies | The scan tool displays the XML Data File Part Number. |
Rear Differential Clutch Control Module Scan Tool Configuration and Setup
| Scan Tool Configuration | Description |
|---|---|
| Program Rear Differential Clutch Calibration Service Value | Function will enter the Rear Differential Clutch Service Calibration Value. |