Common Specs & Procedures Index

CAMARO COMMON SPECS & PROCEDURES

System		Specification/Procedure
Air Conditioning
Service		APPROXIMATE FLUID CAPACITIES
Torque		FASTENER SPECIFICATIONS
Axle Nut/Hub Nut
Front		250 N.m (184 lb in)
Rear		Srep 1: 50 N.m (37 lb ft) Step 2: Additional 45 degrees
Battery		N/A
Brakes
Bleeding Sequence		Manual - RIGHT REAR, LEFT REAR, RIGHT FRONT, LEFT FRONT HYDRAULIC BRAKE SYSTEM BLEEDING (MANUAL J55, J6G) HYDRAULIC BRAKE SYSTEM BLEEDING (MANUAL JL9) Pressure - RIGHT REAR, LEFT REAR, RIGHT FRONT, LEFT FRONT See HYDRAULIC BRAKE SYSTEM BLEEDING (PRESSURE J55, J6G) HYDRAULIC BRAKE SYSTEM BLEEDING (PRESSURE JL9) .
Disc Brakes
	Service Specifications	DISC BRAKE COMPONENT SPECIFICATIONS
	Torque	FASTENER SPECIFICATIONS
Charging
Generator		CHARGING SYSTEM TEST
Torque		FASTENER SPECIFICATIONS
Drive Belts
Adjustment		Non-Adjustable Serpentine Belt
Drive Belt Routing		See illustration under DRIVE BELT REPLACEMENT for 2.0L, DRIVE BELT REPLACEMENT for 3.6L or DRIVE BELT REPLACEMENT - ACCESSORY (LT1) DRIVE BELT REPLACEMENT - ACCESSORY (LT4) SUPERCHARGER BELT REPLACEMENT for 6.2L
Engine Cooling
General Service Specifications		N/A
	Radiator Cap Pressure	Pressure Stamped On Cap
	Thermostat R & I
	2.0L	ENGINE COOLANT THERMOSTAT HOUSING REPLACEMENT (LTG)
	3.6L	ENGINE COOLANT THERMOSTAT HOUSING REPLACEMENT (LGX)
	6.2L	N/A
	Water Pump R & I
	2.0L	WATER PUMP REPLACEMENT (LTG)
	3.6L	WATER PUMP REPLACEMENT (LGX)
	6.2L	WATER PUMP REPLACEMENT (LT1, LT4)
Engine Mechanical
2.0L
	Compression	No cylinder reading should be less than 690 kPa (100 psi). The lowest reading should not be less than 70 percent of the highest reading See ENGINE COMPRESSION TEST
	Oil Pressure - at 700 RPM 100°C	140-200 kPa (20-29 psi)
	Overhaul	ENGINE MECHANICAL SPECIFICATIONS
	Torque	FASTENER SPECIFICATIONS
3.6L
	Compression	No cylinder reading should be less than 690 kPa (100 psi). The lowest reading should not be less than 70 percent of the highest reading See ENGINE COMPRESSION TEST
	Oil Pressure	Minimum @ Idle 69kPa 10psi Minimum @ 2,000 RPM 136 kPa 20psi
	Overhaul	ENGINE MECHANICAL SPECIFICATIONS
	Torque	FASTENER SPECIFICATIONS
6.2L
	Compression	The lowest reading should not be less than 70 percent of the highest reading See ENGINE COMPRESSION TEST
	Oil pressure	152kPa @ 1,000 RPM 22 psig 207 kPa @ 2,000 RPM 30 psig 228 kPa @ 4,000 RPM 33 psig
Overhaul		ENGINE MECHANICAL SPECIFICATIONS (LT1) ENGINE MECHANICAL SPECIFICATIONS (LT4)
	Torque	FASTENER SPECIFICATIONS
Fluid Specifications		See FLUIDS under MAINTENANCE/FLUIDS tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button.
Flywheel/Flex Plate/Drive Plate Torque		2.0L, 3.6L (67 N.m) 49 lb ft 6.2L First Pass 15 N.m 11 lb ft 6.2L Second Pass 30 N.m 22 lb ft 6.2L Final Pass Additional 45 degrees
Fuel System
Pressure Specifications		2.0L KOEO 345-650 kPa (50-94 psi) 3.6L Engine at Idle 300-400 kPa (50-100 psi) 6.2L KOEO 320-608 kPa (46-88 psi)
	Fuel Pressure Test Procedure	2.0L CIRCUIT/SYSTEM VERIFICATION 3.6L CIRCUIT/SYSTEM VERIFICATION 6.2L CIRCUIT/SYSTEM VERIFICATION
	Fuel Filter Location	2.0L Fuel Filter is Part of the Fuel Tank Fuel Pump Module 3.6L Fuel Filter is Part of the Fuel Tank Fuel Pump Module 6.2L Fuel Filter is Part of the Fuel Tank Fuel Pump Module
	Fuel Filter R & I	2.0L FUEL TANK FUEL PUMP MODULE REPLACEMENT 3.6L FUEL TANK FUEL PUMP MODULE REPLACEMENT (SINGLE TRANSFER HOSE) 3.6L FUEL TANK FUEL PUMP MODULE REPLACEMENT (DUAL TRANSFER PIPE) 6.2L FUEL TANK FUEL PUMP MODULE REPLACEMENT (SINGLE TRANSFER PIPE) 6.2L FUEL TANK FUEL PUMP MODULE REPLACEMENT (DUAL TRANSFER PIPE)
Ignition
Firing Order & Cylinder Identification		FIRING ORDER & CYLINDER IDENTIFICATION
Ignition Wires (Resistance)		2.0L Individual Ignition Coil/Module Assemblies 3.6L Individual Ignition Coil/Module Assemblies 6.2L Individual Ignition Coil/Module Assemblies
Ignition Wires (Routing)
2.0L		Coil on Plug
3.6L		Coil on Plug
6.2L		Coil on Plug
Spark Plug
2.0L - Type See parts catalog
	Gap	(0.95-1.10 mm) 0.037-0.043 in
	Torque	(20 N.m) 15 lb ft
3.6L - Type See parts catalog
	Gap	(0.90 mm) 0.035 in
	Torque	(18 N.m) 13 lb ft
6.2L - Type See parts catalog
	Gap	(0.95-1.10 mm) 0.037-0.043 in
	Torque	(20 N.m) 15 lb ft
6.2L - Type See parts catalog
	Gap	(0.95-1.10 mm) 0.037-0.043 in
	Torque	(20 N.m) 15 lb ft
Starting
Starter		N/A
Torque		FASTENER SPECIFICATIONS
Wheel Alignment
	Adjustment Specifications	WHEEL ALIGNMENT SPECIFICATIONS
	Torque	FASTENER SPECIFICATIONS
Wheel & Tire
Wheel Lug Nut Torque		190 N.m (140 lb ft) For wheel nut tightening sequence, see illustration under INSTALLATION PROCEDURE