Common Specs & Procedures Index
VOLT - COMMON SPECS & PROCEDURES
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | Approximate Fluid Capacities | ||
| Torque | Fastener Specifications Automatic: Fastener Specifications |
||
| Front: Wheel Drive Shaft Nut | |||
| First Pass | 150 N.m (111 lb ft) | ||
| Second Pass | Loosen 45 degrees | ||
| Final Pass | 250 N.m (184 lb ft) | ||
| Rear: Wheel Bearing and Hub Bolts | |||
| First Pass | 50 N.m (37 lb ft) | ||
| Final Pass | 30 - 45 degrees | ||
| Battery | Battery Description and Operation | ||
| Brakes | |||
| Bleeding Sequence | Hydraulic Brake System Bleeding | ||
| Disc Brakes | |||
| Service Specifications | Disc Brake Component Specifications | ||
| Torque | Fastener Specifications | ||
| Charging | |||
| Generator | See Drive Motor/Generators under: Charging System Components | ||
| Torque | Fastener Specifications | ||
| Drive Belts | |||
| Adjustment | Serpentine Belt Used, Not Adjustable | ||
| Drive Belt Routing | N/A | ||
| Engine Cooling | |||
| General Service Specifications | Specifications | ||
| Radiator Cap Pressure | Pressure Stamped on Cap | ||
| Thermostat R & I | |||
| 1.5L | Engine Coolant Thermostat Housing Replacement | ||
| Water Pump R & I | |||
| 1.5L | Water Pump Replacement | ||
| Engine Mechanical | |||
| 1.5L | |||
| Compression | Compression Ratio: 12.5:1 Engine Compression Test |
||
| Oil Pressure - @ 1500 RPM 100°C | 200-250 kPa (29-36 psi) | ||
| Overhaul | Specifications | ||
| Torque | Fastener Specifications | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE/FLUIDS tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate/Drive Plate Torque | First Pass - 30 N.m (22 lb ft) Final Pass - Additional 70° |
||
| Fuel System | |||
| Pressure Specification | Engine OFF, Pump Commanded ON - 345-650 kPa (50-94 psi) Engine ON Running - 379-427 kPa (55-62 psi) On Scan Tool |
||
| Fuel Pressure Test Procedure | Circuit/System Verification | ||
| Fuel Filter Location | In the fuel tank, part of the Fuel Tank Fuel Pump Module | ||
| Fuel Filter R & I | Fuel Tank Fuel Pump Module Replacement | ||
| Ignition | |||
| Firing Order & Cylinder Identification | See info and graphic for 4 cylinder engine under: FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires (Resistance) | Individual Ignition Coils | ||
| Ignition Wires (Routing) | |||
| 1.5L | Coil on Plug | ||
| Spark Plug (Type = Refer to Electronic Parts Catalog) | |||
| Gap | 0.60 - 0.70 mm (0.024 - 0.028 in) | ||
| Torque | 17 N.m (13 lb ft) | ||
| Starting | |||
| Starter | Starting System Description and Operation | ||
| Torque | Fastener Specifications | ||
| Wheel Alignment | |||
| Adjustment Specifications | Wheel Alignment Specifications | ||
| Torque | Fastener Specifications | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 140 N.m (103 lb ft) See graphic at "wheel nut tightening sequence" under: Installation Procedure |
||