Common Specs & Procedures Index
TRAVERSE COMMON SPECS & PROCEDURES
| SYSTEM | SPECIFICATION/PROCEDURE | |||
|---|---|---|---|---|
| Air Conditioning | ||||
| Service | APPROXIMATE FLUID CAPACITIES |
|||
| Torque | FASTENER SPECIFICATIONS | |||
| Axle Nut/Hub Nut | ||||
| Front Wheel Drive Shaft Nut | First Pass: 244 lb ft (330 N.m) Second Pass: Loosen 45 degrees Final Pass: 199 lb ft (270 N.m) |
|||
| Rear Wheel Drive Shaft Nut | First Pass: 244 lb ft (330 N.m) Second Pass: Loosen 45 degrees Final Pass: 199 lb ft (270 N.m) |
|||
| Battery | BATTERY REPLACEMENT | |||
| Brakes | ||||
| Bleeding Sequence | RIGHT REAR, LEFT REAR, RIGHT FRONT, LEFT FRONT HYDRAULIC BRAKE SYSTEM BLEEDING (MANUAL) HYDRAULIC BRAKE SYSTEM BLEEDING (PRESSURE) |
|||
| Disc Brakes | ||||
| Service Specifications | DISC BRAKE COMPONENT SPECIFICATIONS | |||
| Torque | FASTENER SPECIFICATIONS | |||
| Charging | ||||
| Generator | GENERATOR REPLACEMENT | |||
| Torque | FASTENER SPECIFICATIONS | |||
| Drive Belts | ||||
| Adjustment | Non-Adjustable Serpentine Belt | |||
| Drive Belt Routing | See Identifying Drive Belt Routing Figure Under DRIVE BELT REPLACEMENT |
|||
| Engine Cooling | ||||
| General Service Specifications | APPROXIMATE FLUID CAPACITIES | |||
| Radiator Cap Pressure | Pressure Stamped On Cap | |||
| Thermostat R & I | ||||
| ENGINE COOLANT THERMOSTAT HOUSING REPLACEMENT or | ||||
| Water Pump R & I | ||||
| WATER PUMP REPLACEMENT | ||||
| Engine Mechanical | ||||
| Compression | The lowest reading should not be less than 70 percent of the highest reading. No cylinder reading should be less than 965 kPa (140 psi). ENGINE COMPRESSION TEST |
|||
| Oil Pressure - Minimum @ Idle: 69 kPa (10 psi) | Oil Pressure - Minimum @ 2000 RPM: 138 kPa (20 psi) | |||
| Overhaul | ENGINE MECHANICAL SPECIFICATIONS | |||
| Torque | FASTENER SPECIFICATIONS | |||
| Fluid Specifications | See FLUIDS under MAINTENANCE/FLUIDS tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | |||
| Flex Plate Torque | First Pass: 30 N.m (22 lb. ft.) Final Pass: Tighten 45° |
|||
| Fuel System | ||||
| Pressure Specification | Ignition ON, Engine OFF - 345-650 kPa (50-94 psi) Engine at IDLE - 300-400 kPa (43-58 psi) |
|||
| Fuel Pressure Test Procedure | FUEL SYSTEM DIAGNOSIS | |||
| Fuel Filter Location | Fuel Filter is Part of the Fuel Tank Fuel Pump Module | |||
| Fuel Filter R & I | FUEL TANK FUEL PUMP MODULE REPLACEMENT (FWD) or FUEL TANK FUEL PUMP MODULE REPLACEMENT (AWD) | |||
| Ignition | ||||
| Firing Order & Cylinder Identification | FIRING ORDER & CYLINDER IDENTIFICATION | |||
| Ignition Wires (Resistance) | Individual Ignition Coil/Module Assemblies | |||
| Ignition Wires (Routing) | ||||
| 3.6L | Coil On Plug | |||
| Spark Plug - For application, see parts catalog | ||||
| Gap | 0.95-1.10 mm (0.0375-0.0433 in) | |||
| Torque | 13 lb ft (18 N.m) | |||
| Starting | ||||
| Starter | STARTER REPLACEMENT | |||
| Torque | FASTENER SPECIFICATIONS | |||
| Wheel Alignment | ||||
| Adjustment Specifications | WHEEL ALIGNMENT SPECIFICATIONS | |||
| Torque | FASTENER SPECIFICATIONS | |||
| Wheel & Tire | ||||
| Wheel Lug Nut Torque | 140 lb ft (190 N.m) For Lug Nut Tightening Sequence, Please See the Figure Under INSTALLATION PROCEDURE |
|||