Common Specs & Procedures Index

COMMON SPECS & PROCEDURES

SYSTEM			SPECIFICATION/PROCEDURE
Air Conditioning
	Service		APPROXIMATE FLUID CAPACITIES
	Torque		FASTENER SPECIFICATIONS
Wheel Drive Shaft Nut
			Front or Rear: First Pass: 330 N.m (244 lb ft) Second Pass: loosen 45 degrees Final Pass: 270 N.m (199 lb ft)
Battery			BATTERY ELECTRICAL DRAIN/PARASITIC LOAD TEST
Brakes
	Bleeding Sequence		RIGHT REAR, LEFT REAR, RIGHT FRONT, LEFT FRONT HYDRAULIC BRAKE SYSTEM BLEEDING (MANUAL WITHOUT JEO) , or HYDRAULIC BRAKE SYSTEM BLEEDING (PRESSURE WITHOUT JEO) , or HYDRAULIC BRAKE SYSTEM BLEEDING (PRESSURE WITH JEO)
	Disc Brakes
		Service Specifications	DISC BRAKE COMPONENT SPECIFICATIONS
		Torque	FASTENER SPECIFICATIONS
Charging
	Generator		CHARGING SYSTEM TEST
	Torque		12 V STARTING AND CHARGING - FASTENER SPECIFICATIONS
Drive Belts
	Adjustment		Non-Adjustable Serpentine Belt
	Drive Belt Routing		See Identifying Drive Belt Routing Figure Under ACCESSORY DRIVE PRIMARY BELT REPLACEMENT (LSY) , or DRIVE BELT REPLACEMENT (LCV) , or DRIVE BELT REPLACEMENT (LGX)
Engine Cooling
	General Service Specifications		SPECIFICATIONS
		Radiator Cap Pressure	RADIATOR SURGE TANK CAP TESTING
		Thermostat R & I
		ENGINE COOLANT THERMOSTAT HOUSING INLET PIPE REPLACEMENT (LSY) , or ENGINE COOLANT THERMOSTAT HOUSING REPLACEMENT (LCV) , or WATER PUMP INLET PIPE REPLACEMENT (LGX)
		Water Pump R & I
		ELECTRIC ENGINE COOLANT PUMP REPLACEMENT (LSY) , or WATER PUMP REPLACEMENT (LCV) , or WATER PUMP REPLACEMENT (LGX)
Engine Mechanical
	2.0L
		Compression	ENGINE COMPRESSION TEST
		Oil Pressure	@ 1500 RPM 100° C: 199.95 kPa (29 psi)
		Overhaul	ENGINE MECHANICAL SPECIFICATIONS
		Torque	FASTENER SPECIFICATIONS
	2.5L
		Compression	ENGINE COMPRESSION TEST
		Oil Pressure	@ 700 RPM 100° C: 154 - 220 kPa (22 - 32 psi)
		Overhaul	ENGINE MECHANICAL SPECIFICATIONS
		Torque	FASTENER SPECIFICATIONS
	3.6L
		Compression	ENGINE COMPRESSION TEST
		Oil Pressure	Minimum @ Idle: 69 kPa (10 psi) Minimum @ 2,000 RPM: 136 kPa (20 psi)
		Overhaul	ENGINE MECHANICAL SPECIFICATIONS
		Torque	FASTENER SPECIFICATIONS
Fluid Specifications			See FLUIDS under MAINTENANCE/FLUIDS tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button.
Flex plate (2.0) Torque			First Pass: 20 N.m (15 lb ft) Final Pass: Tighten 70°
Flex plate (2.5L) Torque			First Pass: 30 N.m (22 lb ft) Final Pass: Tighten 40°
Flex Plate (3.6L) Torque			First Pass: 30 N.m (22 lb ft.) Final Pass: Tighten 45°
Fuel System
		Fuel Pressure Test Procedure	CIRCUIT/SYSTEM VERIFICATION (LSY) , or CIRCUIT/SYSTEM VERIFICATION (LCV) , or CIRCUIT/SYSTEM VERIFICATION (LGX)
		Fuel Filter Location	Fuel Filter is Part of the Fuel Tank Fuel Pump Module
		Fuel Filter R & I	(LSY) FUEL TANK FUEL PUMP MODULE REPLACEMENT (FWD) , or FUEL TANK FUEL PUMP MODULE WIRING HARNESS REPLACEMENT (AWD) (LCV) FUEL TANK FUEL PUMP MODULE REPLACEMENT (LGX) FUEL TANK FUEL PUMP MODULE REPLACEMENT (FWD) , or FUEL TANK FUEL PUMP MODULE REPLACEMENT (AWD)
Ignition
	Firing Order & Cylinder Identification		FIRING ORDER & CYLINDER IDENTIFICATION
	Ignition Wires (Resistance)		Individual Ignition Coil/Module Assemblies
	Ignition Wires (Routing)		Coil On Plug
Spark Plug - For application, see parts catalog
	2.0L
		Gap	0.70 - 0.80 mm (0.028 - 0.031 in)
		Torque	13 lb ft (17 N.m)
	2.5L
		Gap	0.95-1.1 mm (0.037-0.043 in)
		Torque	15 lb ft (20 N.m)
	3.6L
		Gap	0.90 mm (0.035 in)
		Torque	(13 lb ft) 18 N.m
Starting
	Starter		STARTER REPLACEMENT (LGX) , or STARTER REPLACEMENT (LCV) , or STARTER REPLACEMENT (LSY)
	Torque		12 V STARTING AND CHARGING - FASTENER SPECIFICATIONS
Wheel Alignment
		Adjustment Specifications	WHEEL ALIGNMENT SPECIFICATIONS
		Torque	FASTENER SPECIFICATIONS
Wheel & Tire
	Wheel Lug Nut Torque		140 lb ft (190 N.m) For Lug Nut Tightening Sequence, Please See the Figure Under INSTALLATION PROCEDURE