Common Specs & Procedures Index
COMMON SPECS & PROCEDURES
| SYSTEM | SPECIFICATION/PROCEDURE | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | Approximate Fluid Capacities | ||
| Torque | Fastener Specifications | ||
| Wheel Drive Shaft Nut | |||
| Front or Rear: | First Pass: 330 N.m (244 lb ft) Second Pass: loosen 45 degrees Final Pass: 270 N.m (199 lb ft) |
||
| Battery | Battery Electrical Drain/Parasitic Load Test | ||
| Brakes | |||
| Bleeding Sequence | RIGHT REAR, LEFT REAR, RIGHT FRONT, LEFT FRONT Hydraulic Brake System Bleeding (Manual without JEO) , or Hydraulic Brake System Bleeding (Pressure without JEO) , or Hydraulic Brake System Bleeding (Pressure with JEO) |
||
| Disc Brakes | |||
| Service Specifications | Disc Brake Component Specifications | ||
| Torque | Fastener Specifications | ||
| Charging | |||
| Generator | Charging System Test | ||
| Torque | Fastener Specifications | ||
| Drive Belts | |||
| Adjustment | Non-Adjustable Serpentine Belt | ||
| Drive Belt Routing | See Identifying Drive Belt Routing Figure Under Accessory Drive Primary Belt Replacement - 2.0 , or Drive Belt Replacement - 3.6 |
||
| Engine Cooling | |||
| General Service Specifications | Specifications | ||
| Radiator Cap Pressure | Radiator Surge Tank Cap Testing | ||
| Thermostat R & I | |||
| Engine Coolant Thermostat Housing Inlet Pipe Replacement (LSY) , or Engine Coolant Thermostat Housing Inlet Pipe Replacement (LGX) | |||
| Water Pump R & I | |||
| Electric Engine Coolant Pump Replacement (LSY) , or Water Pump Replacement (LGX) | |||
| Engine Mechanical | |||
| 2.0L | |||
| Compression | Engine Compression Test - 2.0 | ||
| Oil Pressure | @ 1500 RPM 100°C: 199.95 kPa (29 psi) | ||
| Overhaul | Engine Mechanical Specifications | ||
| Torque | Fastener Specifications | ||
| 3.6L | |||
| Compression | Engine Compression Test | ||
| Oil Pressure | Minimum @ Idle: 69 kPa (10 psi) Minimum @ 2000 RPM: 136 kPa (20 psi) |
||
| Overhaul | Engine Mechanical Specifications | ||
| Torque | Fastener Specifications | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE/FLUIDS tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flex Plate (2.0) Torque | First Pass: 20 N.m (15 lb ft) Final Pass: Tighten 70° |
||
| Flex Plate (3.6L) Torque | First Pass: 30 N.m (22 lb ft.) Final Pass: Tighten 45° |
||
| Fuel System | |||
| Fuel Pressure Test Procedure | CIRCUIT/SYSTEM VERIFICATION - 2.0 , or CIRCUIT/SYSTEM VERIFICATION - 3.6 | ||
| Fuel Filter Location | Fuel Filter is Part of the Fuel Tank Fuel Pump Module | ||
| Fuel Filter R & I | (LSY) Fuel Tank Fuel Pump Module Replacement (FWD)
or Fuel Tank Fuel Pump Module Replacement (AWD) (LGX) Fuel Tank Fuel Pump Module Replacement (FWD) or Fuel Tank Fuel Pump Module Replacement (AWD) |
||
| Ignition | |||
| Firing Order & Cylinder Identification | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires (Resistance) | Individual Ignition Coil/Module Assemblies | ||
| Ignition Wires (Routing) | Coil On Plug | ||
| Spark Plug - For application, see parts catalog | |||
| 2.0L | |||
| Gap | 0.70 - 0.80 mm (0.028 - 0.031 in) | ||
| Torque | 17 N.m (13 lb ft) | ||
| 3.6L | |||
| Gap | 0.90 mm (0.035 in) | ||
| Torque | 18 N.m (13 lb ft) | ||
| Starting | |||
| Starter | Starter Replacement (LSY) , or Starter Replacement (LGX) | ||
| Torque | Fastener Specifications | ||
| Wheel Alignment | |||
| Adjustment Specifications | Wheel Alignment Specifications | ||
| Torque | Fastener Specifications | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 190 N.m (140 lb ft) For Lug Nut Tightening Sequence, Please See The Figure Under Installation Procedure |
||