LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Chrysler >> 2007 >> 300 Base >> Repair and Diagnosis >> External Pages >> Different car >> Section 165 (Electronic Control Modules (Service Information)) >> Electronic Control Modules - Service Information >> Module-Engine Control >> Standard Procedure >> Pcm/ECM Programming - Diesel >> Section 2 - Additional Pcm / TCM Replacement Procedures
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Section 2 - Additional Pcm / TCM Replacement Procedures

WARNING: This page is about a different car, the 2007 Chrysler PT Cruiser. However, it is still accessible from the selected car via links, so may be relevant.

STEPS-BY-STEP INSTRUCTIONS 

Check PCM VIN  

From the "Home" screen, select "ECU View"

  1. Select "PCM"
  2. Select "Misc. Functions"
  3. Select "Check PCM VIN" and follow the on screen instructions.
  4. When complete, select "Finish"

Diesel Particulate Filter (Used) Learning 

From the "Home" screen, select "ECU View"

  1. Select "PCM"
  2. Select "Misc. Functions"
  3. Select "Diesel Particulate Filter (Used) Learning" and follow the on screen instructions.
  4. When complete, select "Finish"

ECU Replacement with Value Transfer 

From the "Home" screen, select "ECU View"

  1. Select "PCM"
  2. Select "Misc. Functions"
  3. Select "ECU Replacement with Value Transfer" and follow the on screen instructions.
  4. When complete, select "Finish"

ECU Replacement without Value Transfer 

From the "Home" screen, select "ECU View"

  1. Select "PCM"
  2. Select "Misc. Functions"
  3. Select "ECU Replacement without Value Transfer" and follow the on screen instructions.
  4. When complete, select "Finish"

Enable / Disable Vehicle Features 

From the "Home" screen, select "ECU View"

  1. Select "PCM"
  2. Select "Misc. Functions"
  3. Select "Enable / Disable Vehicle Features" and follow the on screen instructions.
  4. When complete, select "Finish"

Exhaust Throttle Plate Adaptive Learn Position 

From the "Home" screen, select "ECU View"

  1. Select "PCM"
  2. Select "Misc. Functions"
  3. Select "Exhaust Throttle Plate Adaptive Learn Position" and follow the on screen instructions.
  4. When complete, select "Finish"

Fuel Mean Value Adaptation Initialization  

From the "Home" screen, select "ECU View"

  1. Select "PCM"
  2. Select "Misc. Functions"
  3. Select "Fuel Mean Value Adaptation Initialization" and follow the on screen instructions.
  4. When complete, select "Finish"

IMA Rapid Calibration  

From the "Home" screen, select "ECU View"

  1. Select "PCM"
  2. Select "Misc. Functions"
  3. Select "IMA Rapid Calibration Test" and follow the on screen instructions.
  4. When complete, select "Finish"

Initialize EGS 

From the "Home" screen, select "ECU View"

  1. Select "PCM"
  2. Select "Misc. Functions"
  3. Select "Initialize EGS" and follow the on screen instructions.
  4. When complete, select "Finish"

Injector Quantity Adjustment 

From the "Home" screen, select "ECU View"

  1. Select "PCM"
  2. Select "Misc. Functions"
  3. Select "Injector Quantity Adjustment" and follow the on screen instructions.
  4. When complete, select "Finish"

Mobile DeSoot - NO Minimum Required Soot Load 

From the "Home" screen, select "ECU View"

  1. Select "PCM"
  2. Select "Misc. Functions"
  3. Select "Mobile DeSoot - NO Minimum Required Soot Load" and follow the on screen instructions.
  4. When complete, select "Finish"

NOx Catalyst(New) Initialization 

From the "Home" screen, select "ECU View"

  1. Select "PCM"
  2. Select "Misc. Functions"
  3. Select "NOx Catalyst(New) Initialization" and follow the on screen instructions.
  4. When complete, select "Finish"

PCM Replaced  

The vehicle pin (Personal Identification Number) will be required to complete the routine. This information may be obtained in three ways:

  1. The original selling invoice
  2. DealerCONNECT > Parts > Key Codes
  3. Contacting the District Manager.

From the "Home" screen, select "ECU View"

  1. Select "WCM"
  2. Select "Misc. Functions"
  3. Select "PCM Replaced" and follow the on screen instructions.
  4. When complete, select "Finish"

Program Variant Code 

From the "Home" screen, select "ECU View"

  1. Select "PCM"
  2. Select "Misc. Functions"
  3. Select "Program Variant Code" and follow the on screen instructions.
  4. When complete, select "Finish"

Quicklearn 

From the "Home" screen, select "ECU View"

  1. Select "PCM"
  2. Select "Misc. Functions"
  3. Select "Quicklearn" and follow the on screen instructions.
  4. When complete, select "Finish"

Reset Regenerative Filter Timers 

From the "Home" screen, select "ECU View"

  1. Select "PCM"
  2. Select "Misc. Functions"
  3. Select "Reset Regenerative Filter Times" and follow the on screen instructions.
  4. When complete, select "Finish"

Set Oil Dilution Mass Value 

From the "Home" screen, select "ECU View"

  1. Select "PCM"
  2. Select "Misc. Functions"
  3. Select "Set Oil Dilution Mass Value" and follow the on screen instructions.
  4. When complete, select "Finish"

If an EDC16-U31 PCM was replaced, perform the following additional steps and/or routines: 

  1. PCM Replaced - if WCM equipped
  2. Check PCM VIN - if NOT WCM equipped
  3. Program Variant Code

    If an EDC16-C2 PCM was replaced, perform the following additional steps and/or routines: 

  4. PCM Replaced - if WCM equipped
  5. Check PCM VIN - if NOT WCM / SKREEM equipped
  6. IMA Rapid Calibration Test - Only on 06 PT & up
  7. Injector Quantity Adjustment - Only on 06 PT & up

    If an EDC16-CP31 was replaced, perform the following additional steps and/or routines: 

  8. PCM Replaced - if WCM equipped
  9. Check PCM VIN - if NOT WCM equipped
  10. Diesel Particulate Filter (Used) Learning
  11. NOx Catalyst(New) Initialization
  12. Injector Quantity Adjustment
  13. IMA Rapid Calibration Test
  14. Fuel Mean Value Adaptation Initialization
  15. Exhaust Throttle Plate Adaptive Learn Position

    If an EDC16-CP31-2 was replaced, perform the following additional steps and/or routines: 

  16. PCM Replaced - if WCM equipped
  17. Check PCM VIN - if NOT WCM equipped
  18. Injector Quantity Adjustment
  19. Program Variant Code
  20. ECU Replacement With Value Transfer - if the ECU to be replaced is still responsive
  21. ECU Replacement Without Value Transfer - if the ECU to be replaced is NOT responsive
  22. Fuel Mean Value Adaptation Initialization
  23. IMA Rapid Calibration Test
  24. Set Oil Dilution Mass Value

    If a CM849 PCM was replaced, perform the following additional steps and/or routines: 

  25. PCM Replaced - if WCM equipped
  26. Check PCM VIN - if NOT WCM equipped

    If a CM2100 PCM was replaced, perform the following additional steps and/or routines: 

  27. PCM Replaced - if WCM equipped
  28. Check PCM VIN - if NOT WCM equipped
  29. Enable / Disable Vehicle Features - need to enable features
  30. Injector Quantity Adjustment
  31. Reset Regenerative Filter Timers
  32. Mobile DeSoot - NO Minimum Required Soot Load

    If an Aisin TCM was replaced, perform the following additional steps and/or routines: 

  33. Quicklearn

    If an EGS TCM was replaced, perform the following additional steps and/or routines: 

  34. Initialize EGS

    If an NGC4 TCM ONLY was replaced, perform the following additional steps and/or routines: 

  35. Quicklearn

    If an NGC3 TCM ONLY was replaced, perform the following additional steps and/or routines: 

  36. Quicklearn

    If an EATX TCM was replaced, perform the following additional steps and/or routines: 

  37. Quicklearn
scientia non olet · About LEMON Manuals