RF-Hub, Pcm And BCM Replacement And Programming Order Guide
WARNING: This page is about a different car, the 2015 Dodge Viper. However, it is still accessible from the selected car via links, so may be relevant.
| Module |
POWERNET MODULE REPLACEMENT GUIDE (RF-HUB, PCM and BCM) |
| Condition 1 |
Condition 2 |
Condition 3 |
Condition 4 |
Condition 5 |
Condition 6 |
Condition 7 |
Condition 8 |
| RF-HUB (and ELV/ESCL if equipped) |
New |
Existing |
Existing |
Existing |
New |
New |
New |
Existing |
| BCM |
Existing |
New |
Existing |
Existing |
New |
Existing |
Existing |
New |
| FOBIKs |
Existing |
Existing |
New |
Existing |
Existing |
New |
Existing |
New |
| PCM |
Existing |
Existing |
Existing |
New |
Existing |
Existing |
New |
Existing |
| PROGRAMMING ORDER |
ASSOCIATED SCAN TOOL FUNCTION |
| 1 |
Program Ignition FOBIKs (ignition off) |
Cycle ignition on and wait 10 seconds |
Program Ignition FOBIKs (ignition off) |
Flash update PCM (if PCM arrives in a generic state) |
Run Restore Vehicle Configuration (should enable PCM and RF-HUB) |
Program Ignition FOBIKs (ignition off) |
Program Ignition FOBIKs (ignition off) |
Program Ignition FOBIKs (ignition off) |
| 2 |
RF-HUB Replace |
BCM Replace (in RFH) |
---- |
Check PCM VIN and other PCM routines |
Program Ignition FOBIKs (ignition off) |
RF-HUB Replace |
Flash PCM (if PCM arrives in a generic state) |
Cycle ignition on and wait 10 seconds |
| 3 |
---- |
---- |
---- |
---- |
Run Restore Vehicle Configuration again to write full configuration |
---- |
Check PCM VIN and other PCM routines |
BCM Replace (in RFH) |
| 4 |
---- |
---- |
---- |
---- |
RF-HUB Replace |
---- |
RF-HUB Replace |
---- |
| 5 |
---- |
---- |
---- |
---- |
BCM Replace (in RFH) |
---- |
---- |
---- |
| Module |
MODULE REPLACEMENT GUIDE (RF-HUB, BCM, PCM, FOBiK and ELV) |
| Condition 9 |
Condition 10 |
Condition 11 |
Condition 12 |
Condition 13 |
Condition 14 |
Condition 15 |
| RF-HUB (and ELV/ESCL if equipped) |
Existing |
Existing |
Existing |
New |
New |
New |
New Part |
| BCM |
New |
Existing |
New |
Existing |
New |
New |
New Part |
| FOBiKs |
Existing |
New |
New |
New |
Existing |
New |
New Part |
| PCM |
New |
New |
New |
New |
New |
Existing |
New Part |
| PROGRAMMING ORDER |
ASSOCIATED SCAN TOOL FUNCTION |
| 1 |
Flash update PCM (if PCM arrives in a generic state) |
Program Ignition FOBIKs (ignition off) |
Program Ignition FOBIKs (ignition off) |
Program Ignition FOBIKs (ignition off) |
Run Restore Vehicle Configuration (should enable PCM and RF-HUB) |
Run Restore Vehicle Configuration (should enable PCM and RF-HUB) |
Run Restore Vehicle Configuration (should enable PCM and RF-HUB) |
| 2 |
Check PCM VIN and other PCM routines |
Flash update PCM (if PCM arrives in a generic state) |
Flash update PCM (if PCM arrives in a generic state) |
Flash update PCM (if PCM arrives in a generic state) |
Program Ignition FOBIKs (ignition off) |
Program Ignition FOBIKs (ignition off) |
Program Ignition FOBIKs (ignition off) |
| 3 |
BCM Replace (in RFH) |
Check PCM VIN and other PCM routines |
Check PCM VIN and other PCM routines |
Check PCM VIN and other PCM routines |
Flash update PCM (if PCM arrives in a generic state) |
Run Restore Vehicle Configuration again to write full configuration |
Flash update PCM (if PCM arrives in a generic state) |
| 4 |
---- |
---- |
BCM Replace (in RFH) |
RF-HUB Replace |
Check PCM VIN and the other needed PCM routines |
RF-HUB Replace |
Check PCM VIN and the other needed PCM routines |
| 5 |
---- |
---- |
---- |
---- |
Run Restore Vehicle Configuration again to write full configuration |
---- |
Run Restore Vehicle Configuration again to write full configuration |
| 6 |
---- |
---- |
---- |
---- |
RF-HUB Replace |
---- |
RF-HUB Replace |
| 7 |
---- |
---- |
---- |
---- |
BCM Replace (in RFH) |
---- |
BCM Replace (in RFH) |