LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Fiat >> 2020 >> 500L Pop >> Repair and Diagnosis >> External Pages >> Different car >> Section 10 (Electronic Control Modules (Service Information)) >> Module, Anti-Lock Brake System (Abs) >> Installation >> Left-Hand Drive
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Left-Hand Drive

WARNING: This page is about a different car, the 2020 Dodge Journey. However, it is still accessible from the selected car via links, so may be relevant.
  1. Clean any debris off the mating surfaces of the HCU and ABM.
    CAUTION:

    When installing new O-rings or solenoid valve stem seals, do not use any type of lubricant.

    GC0124493Courtesy of CHRYSLER GROUP, LLC
    1 - SEAL
    2 - SOLENOID VALVE STEM
  2. If the seals (1) on the solenoid valve stems (2) are not new, replace them all  . Each of the solenoid valve stem seals must be new  to keep out moisture and debris;do not reuse solenoid valve stem seals. 
    GC0124494Courtesy of CHRYSLER GROUP, LLC
    1 - O-RING
    2 - O-RING MOUNTING GROOVE
  3. Replace the pump/motor connector O-ring (1) if it is not new. Be sure the O-ring is properly seated in the mounting groove (2).
    GC0081324Courtesy of CHRYSLER GROUP, LLC
    1 - ABM
    2 - HCU
    3 - SOLENOID VALVE STEM
  4. Align components and install the ABM (1) on the HCU (2).
    GC0128570Courtesy of CHRYSLER GROUP, LLC
  5. Install the fasteners (1) attaching the ABM (2) to the HCU. Tighten the ABS ABM fasteners to the proper torque specifications. Refer to TORQUE SPECIFICATIONS .
    GC0081322Courtesy of CHRYSLER GROUP, LLC
    1 - ABM (PART OF ICU)
    2 - WIRING HARNESS CONNECTOR
    CAUTION:

    Before installing the ABM harness connector on the ABM, be sure the seal is properly installed in the connector.

  6. Insert the ABM wiring harness connector (2) into the socket of the ABM (1) and close the cover, locking the connector in place.
  7. Raise and support the vehicle Refer to HOISTING, STANDARD PROCEDURE .
    GC0082347Courtesy of CHRYSLER GROUP, LLC
  8. Loosen the fasteners (2) as necessary and allow the ICU (1) mounting bracket to slide down over the fasteners and hang the assembly in place. Tighten the ABS ICU mounting bracket fasteners (2) to the proper torque specifications. Refer to .
  9. Lower the vehicle.
  10. Position the fresh air plenum and install the fasteners.
    GC0128486Courtesy of CHRYSLER GROUP, LLC
  11. Install the wheelhouse brace (2). Install and tighten the wheelhouse brace fasteners (1) to the proper torque specifications. Refer to TECHNICAL SPECIFICATIONS .
    GC0128455Courtesy of CHRYSLER GROUP, LLC
  12. Install the cowl screen. Install the fasteners (1) securing the cowl screen to the wheelhouse brace and cowl. Rotate the fasteners (2) in the center of the cowl screen 90° counterclockwise to lock the screen in place.
  13. Install the wiper arms Refer to ARM, WIPER, INSTALLATION .
    GC0128454Courtesy of CHRYSLER GROUP, LLC
  14. Install the cowl top screen (3). Install the fasteners (1) securing the cowl top screen at the ends. Install the remaining fasteners (2).
  15. Install the engine appearance cover.
  16. Connect the negative battery cable. If equipped with an Intelligent Battery Sensor (IBS), connect the IBS connector.
  17. Connect the diagnostic scan tool to initialize the ABM and perform the following:
    1. Clear any faults.
    2. Perform the ABS Verification Test and road test the vehicle. Refer to ABS VERIFICATION TEST .
scientia non olet · About LEMON Manuals