- No communication with the electronic automatic temperature control (EATC) module
|
- Circuitry short/open.
- EATC module communication network.
|
|
- The EATC system is inoperative, intermittent or incorrect operation
|
- Circuitry short/open.
- Input sensor (s)/erratic input signals.
- Automatic temperature control aspirator hose and elbow.
|
|
- Incorrect/erratic direction of airflow from outlets
|
- Circuitry short/open.
- Door actuator.
- Mode door binding or stuck.
- EMTC module or EATC module
- Door actuator arm not connected to the door crank.
|
|
- Insufficient, erratic, or no heat
|
- Low engine coolant level.
- Engine overheating.
- Plugged or partially plugged heater core.
- Temperature blend door is binding or stuck.
- Temperature blend door actuator.
- Heater hose is kinked or binding.
|
|
- The A/C is inoperative/does not operate correctly
|
- Open fuse.
- Circuitry short/open.
- A/C system discharged/low charge.
- A/C pressure transducer.
- PCM.
- EATC module.
- EMTC module.
- A/C cycling switch.
- A/C compressor clutch air gap.
- A/C clutch relay.
|
|
|
|
- Circuitry short/open.
- EATC module.
- EMTC module.
- PCM.
- A/C compressor clutch air gap.
- A/C clutch relay.
|
|
- The temperature control is inoperative/does not operate correctly
|
- Circuitry open/shorted.
- EMTC module.
- EATC module.
- Temperature blend door.
- Temperature blend door actuator.
- Door actuator arm not connected to the door crank.
|
|
- The blower motor is inoperative - EMTC
|
- Fuse.
- Circuitry open/shorted.
- A/C blower motor switch.
- Blower motor relay.
- A/C blower motor.
- EMTC module. SJB.
|
|
- The blower motor does not operate correctly - EMTC
|
- Circuitry shorted.
- A/C blower motor resistor.
- A/C blower motor switch.
|
|
- The blower motor is inoperative - EATC
|
- Circuitry short/open.
- Blower motor relay.
- A/C blower motor.
- EATC module.
- SJB.
- A/C blower motor speed control.
|
|
- The blower motor does not operate correctly - EATC
|
- Circuitry short/open.
- A/C blower motor speed control.
- EATC module.
- A/C blower motor speed control.
|
|
- The auxiliary blower motor is inoperative
|
- Fuse.
- Circuitry short/open.
- Auxiliary blower motor resistor.
- Auxiliary blower motor.
|
|
- The auxiliary blower motor does not operate correctly
|
- Fuse.
- Circuitry short/open.
- Auxiliary blower motor relay.
- Auxiliary blower motor speed relay 1.
- Auxiliary blower motor speed relay 2.
- Rear auxiliary control.
- Auxiliary blower motor resistor.
|
|
- The auxiliary temperature control only is inoperative/does not operate correctly
|
- Fuse.
- Circuitry short/open.
- SJB.
- Auxiliary blend door actuator.
- Auxiliary blend door.
|
|
- The auxiliary panel/floor control only is inoperative/does not operate correctly
|
- Fuse.
- Circuitry short/open.
- SJB.
- Auxiliary mode door actuator.
- Auxiliary mode door.
|
|
- The auxiliary temperature and panel/floor control is inoperative/does not operate correctly
|
- Fuse.
- Circuitry short/open.
- Rear auxiliary control.
- SJB.
|
|
- Insufficient air conditioning (A/C) cooling
|
- Low refrigerant level.
- Temperature blend door actuator.
|
|
- The dual temperature control is inoperative/does not operate correctly
|
- Temperature blend door/actuator broken/binding
- EMTC/EATC module
- Low A/C refrigerant charge
|
- Check that the A/C system pressure is above 290 kPa (42 psi). If the pressure is below 290 kPa (42 psi) refer to FLUORESCENT DYE LEAK DETECTION . CHECK the temperature blend doors/actuators for a binding or broken condition. If no condition is found, INSTALL a new EMTC/EATC module.
|
- The temperature set point does not repeat after turning the ignition switch OFF
|
- Open fuse.
- Circuitry short/open.
- EATC module.
|
- CHECK circuit 1001 (WH/YE) for a short or open and repair as necessary. If okay, INSTALL a new EATC module.
|
- The temperature display will not switch between Celsius and Fahrenheit
|
|
- If the instrument cluster does not switch between English and Metric, refer to INFORMATION, GAUGES & WARNING DEVICES
.
- If only the EATC module does not switch between English and Metric, INSTALL a new EATC module.
|