LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Ford >> 2014 >> Focus ST >> Repair and Diagnosis >> Engine Mechanical >> Fuel System >> Fuel System - General Information - 2.0L ECOBOOST >> General Procedures >> Quick Release Coupling >> Disconnect
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Quick Release Coupling: Disconnect

NOTE: When reusing liquid or vapor tube connections, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 1
  1. WARNING: Before beginning any service procedure in this service information, refer to Safety Warnings in GENERAL INFORMATION . Failure to follow this instruction may result in serious personal injury.

    Refer to: GASOLINE AND GASOLINE-ETHANOL FUEL SYSTEMS HEALTH AND SAFETY PRECAUTIONS .

  2. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure.

    Refer to: FUEL SYSTEM PRESSURE RELEASE .

  3. Disconnect the battery ground cable.

    Refer to: BATTERY DISCONNECT AND CONNECT .

  4. Separate the tabs of the retainer clip and pull it to the outward position in the quick release coupling
    G08065057
  5. Depress the retainer clip and disconnect the quick release coupling from the tube.
    G08065058


NOTE: When reusing liquid or vapor tube connections, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 2
  1. WARNING: Before beginning any service procedure in this service information, refer to Safety Warnings in GENERAL INFORMATION . Failure to follow this instruction may result in serious personal injury.

    Refer to: GASOLINE AND GASOLINE-ETHANOL FUEL SYSTEMS HEALTH AND SAFETY PRECAUTIONS .

  2. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure.

    Refer to: FUEL SYSTEM PRESSURE RELEASE .

  3. Disconnect the battery ground cable.

    Refer to: BATTERY DISCONNECT AND CONNECT .

  4. Release the lock tab on the quick release coupling.
    G08065061
  5. Separate the quick release coupling from the fitting.
    G08065062


NOTE: When reusing liquid or vapor tube connections, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 3
  1. WARNING: Before beginning any service procedure in this service information, refer to Safety Warnings in GENERAL INFORMATION . Failure to follow this instruction may result in serious personal injury.

    Refer to: GASOLINE AND GASOLINE-ETHANOL FUEL SYSTEMS HEALTH AND SAFETY PRECAUTIONS .

  2. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure.

    Refer to: FUEL SYSTEM PRESSURE RELEASE .

  3. Disconnect the battery ground cable.

    Refer to: BATTERY DISCONNECT AND CONNECT .

  4. Disconnect the fuel tube quick release coupling.
    G08065065
  5. Separate the quick release coupling from the fitting.
    G08065066


NOTE: When reusing liquid or vapor tube connections, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 4
  1. WARNING: Before beginning any service procedure in this service information, refer to Safety Warnings in GENERAL INFORMATION . Failure to follow this instruction may result in serious personal injury.

    Refer to: GASOLINE AND GASOLINE-ETHANOL FUEL SYSTEMS HEALTH AND SAFETY PRECAUTIONS .

  2. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure.

    Refer to: FUEL SYSTEM PRESSURE RELEASE .

  3. Disconnect the battery ground cable.

    Refer to: BATTERY DISCONNECT AND CONNECT .

  4. Press both retaining tabs inward and remove quick release coupling from fuel tube.
    G08065068
scientia non olet · About LEMON Manuals