Common Specifications & Procedures

EDGE/MKX COMMON SPECIFICATIONS & PROCEDURES

System				Specifications/Procedures
Air Conditioning
	Service			SPECIFICATIONS
	Torque			SPECIFICATIONS
Axle Nut/Hub Nut
	Front			98 lb.ft (133 Nm)
	Rear
		AWD		98 lb.ft (133 Nm)
		FWD		98 lb.ft (133 Nm)
Battery				SPECIFICATIONS
Brakes
	Bleeding Sequence			BRAKE SYSTEM PRESSURE BLEEDING
	Front Disc Brakes w/Torque			BRAKE DISC
	Rear Disc Brakes w/Torque			BRAKE DISC
Charging
	Generator w/Torque			SPECIFICATIONS
Drive Belts
	Adjustment
		2.0L ECOBOOST (184KW/250PS) - MI4		ACCESSORY DRIVE
		2.7L EcoBoost (238kW/324PS)		ACCESSORY DRIVE
		3.5L Duratec (212kW/278PS)		ACCESSORY DRIVE
	Belt Routing
		2.0L ECOBOOST (184KW/250PS) - MI4		ACCESSORY DRIVE - COMPONENT LOCATION
		2.7L EcoBoost (238kW/324PS)		ACCESSORY DRIVE - COMPONENT LOCATION
		3.5L Duratec (212kW/278PS)		ACCESSORY DRIVE - COMPONENT LOCATION
Engine Cooling
	General Service Specifications
		2.0L ECOBOOST (184KW/250PS) - MI4		SPECIFICATIONS
		2.7L EcoBoost (238kW/324PS)		SPECIFICATIONS
		3.5L Duratec (212kW/278PS)		SPECIFICATIONS
	Radiator Cap Pressure			145 kPa (21 psi)
	Thermostat R & I
		2.0L GDTI		THERMOSTAT HOUSING
		2.7L		THERMOSTAT
		3.5L		THERMOSTAT HOUSING
	Water Pump R & I
		2.0L GDTI		COOLANT PUMP
		2.7L		COOLANT PUMP
		3.5L		COOLANT PUMP
Engine Mechanical
	2.0L GDTI
		Compression		SPECIFICATIONS
		Oil Pressure (Hot @ 2000 RPM)		29-60 psi (200-414 kPa)
		Overhaul		SPECIFICATIONS
			Torque
	2.7L
		Compression		SPECIFICATIONS
		Oil Pressure (minimum at 1, 500 RPM with engine at normal operating temperature.)		20 psi (137.8 kPa)
		Overhaul		SPECIFICATIONS
			TorqueSPECIFICATIONS
	3.5L
		Compression		SPECIFICATIONS
		Oil Pressure (minimum at 1, 500 RPM with engine at normal operating temperature.)		30.0psi (206.8kPa)
		Overhaul		SPECIFICATIONS
			Torque
Fluid Specifications				See FLUIDS under MAINTENANCE tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button.
Flywheel/Flex Plate Torque
	2.0L GDTI			Stage 1: 50 Nm (37 lb-ft). Stage 2: 80 Nm (50 lb-ft). Stage 3: 112 Nm (83 lb-ft).
	2.7L			59 lb.ft (80 Nm)
	3.5L			59 lb.ft (80 Nm)
Fuel System
	Fuel Filter Location			Located in fuel tank as part of Fuel Pump Module.
	Fuel Filter R & I
		2.0L GDTI		FUEL PUMP AND SENDER UNIT
		2.7L		FUEL PUMP AND SENDER UNIT
		3.5L		FUEL PUMP AND SENDER UNIT
	Pressure Release Procedure
		2.0L GDTI		FUEL SYSTEM PRESSURE RELEASE
		2.7L		FUEL SYSTEM PRESSURE RELEASE
		3.5L		FUEL SYSTEM PRESSURE RELEASE
	Pressure Specification
		2.0L GDTI		SPECIFICATIONS
		2.7L		SPECIFICATIONS
		3.5L		SPECIFICATIONS
		Fuel Pressure Test Procedure
		2.0L GDTI		FUEL SYSTEM PRESSURE CHECK
		2.7L		FUEL SYSTEM PRESSURE CHECK
		3.5L		FUEL SYSTEM PRESSURE CHECK
Ignition
	Firing Order & Cylinder Identification			FIRING ORDER & CYLINDER IDENTIFICATION
	Ignition Wires (Routing)			Engines are equipped with Coil-on-plug ignition.
Spark Plugs
	2.0L GTDI
		Type		CYFS12Y-2
		Gap		.031 In. (0.8 mm) (2.0L EcoBoost (184kW/250PS) - MI4 ) 0.030 in (.75 mm) (2.0L EcoBoost (184kW/250PS))
		Torque		106 In. Lbs. (12 N.m)
	2.7L
		Type		Motorcraft CYFS12F-5
		Gap		0.028-0.031 in (0.7-0.8 mm)
		Torque		133 In. Lbs. (15 N.m)
	3.5L
		Type		Motorcraft CYFS12F-5
		Gap		.049-.053 In. (1.25-1.35 mm)
		Torque		133 In. Lbs. (15 N.m)
Starting
	Starter
		2.0L		SPECIFICATIONS
		2.7L		SPECIFICATIONS
		3.5L		SPECIFICATIONS
	Torque
		2.0L		STARTER MOTOR
		2.7L		STARTER MOTOR
		3.5L		STARTER MOTOR
Wheel Alignment
	Adjustment Specifications			SPECIFICATIONS
	Torque			TORQUE SPECIFICATIONS
Wheel & Tire
	Wheel Lug Nut Torque			: 162 lb.ft (220 Nm)