LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Ford >> 2023 >> Escape Plug-In Hybrid >> Repair and Diagnosis >> External Pages >> Different car >> Section 1528 (MULTIFUNCTION Electronic Modules) >> Diagnosis And Testing >> Body Control Module (BCM) >> Pinpoint Tests >> Pinpoint Test M: U0230:87
July 1: So it begins. Don't worry, this is not in the correct legal jurisdiction!

Pinpoint Test M: U0230:87

WARNING: This page is about a different car, the 2023 Lincoln Nautilus. However, it is still accessible from the selected car via links, so may be relevant.
  1. Refer to MODULE COMMUNICATIONS NETWORK for schematic and connector information.

    Normal Operation and Fault Conditions 

    DTC Fault Trigger Conditions 

    DTC Description Fault Trigger Condition
    BCM U0230:87 Lost Communication With Rear Gate Module: Missing Message A continuous memory DTC that sets in the BCM if messages from the RGTM through the GWM are missing.

    Possible Sources 

    • Communication network concern
    • Battery voltage concern
    • RGTM module
    • BCM

  2. M1 CHECK THE COMMUNICATION NETWORK

    • Using a diagnostic scan tool, perform a network test.

    Does the RGTM pass the network test? 

    Yes  GO to  M2
    No 

  3. M2 CHECK THE BCM (BODY CONTROL MODULE) CONTINUOUS MEMORY DIAGNOSTIC TROUBLE CODES (CMDTCS)

    • Using a diagnostic scan tool, clear the Diagnostic Trouble Codes (DTCs).

    • Wait 10 seconds.

    • Using a diagnostic scan tool, check the BCM Continuous Memory Diagnostic Trouble Codes (CM DTCs).

    Is DTC U3006:16, U3006:17, U3007:16, U3007:17, U3013:16, U3013:17, U3014:16 or U3014:17 recorded? 

    Yes  For DTC U3006:16, U3007:16, U3013:16 or U3014:16, GO to Pinpoint Test U 
    For DTC U3006:17, U3007:17, U3013:17 or U3014:17, GO to Pinpoint Test W 
    No  GO to  M3

  4. M3 RETRIEVE THE RGTM (REAR GATE TRUNK MODULE) DIAGNOSTIC TROUBLE CODES (DTCS) FROM THE SELF-TEST

    • Using a diagnostic scan tool, perform the RGTM self-test.

    Are any Diagnostic Trouble Codes (DTCs) recorded? 

    Yes  REFER to: Body Closures .
    No  GO to  M4

  5. M4 RECHECK THE BCM (BODY CONTROL MODULE) CONTINUOUS MEMORY DIAGNOSTIC TROUBLE CODES (CMDTCS)

    • Using a diagnostic scan tool, clear the Diagnostic Trouble Codes (DTCs).

    • Wait 10 seconds.

    • Using a diagnostic scan tool, check the BCM Continuous Memory Diagnostic Trouble Codes (CM DTCs).

    Is DTC U0230:87 still present? 

    Yes  GO to  M5
    No  The system is operating correctly at this time. The DTC may have been set due to high network traffic or an intermittent fault condition.

  6. M5 CHECK FOR DTC (DIAGNOSTIC TROUBLE CODE) U0230:87 SET IN OTHER MODULES

    • Using a diagnostic scan tool, clear the Diagnostic Trouble Codes (DTCs).

    • Ignition OFF.

    • Ignition ON.

    • Wait 10 seconds.

    • Using a diagnostic scan tool, retrieve all 

      Continuous Memory Diagnostic Trouble Codes (CM DTCs).

    Is DTC U0230:87 set in other moduleS? 

    Yes  GO to  M6
    No  GO to  M7

  7. M6 CHECK FOR CORRECT RGTM (REAR GATE TRUNK MODULE) OPERATION

    • Disconnect and inspect the RGTM connector.

    • Repair:

      • corrosion (install new connector or terminals - clean module pins)
      • damaged or bent pins - install new terminals/pins
      • pushed-out pins - install new pins as necessary

    • Reconnect the RGTM connector. Make sure it seats and latches correctly.

    • Operate the system and determine if the concern is still present.

    Is the concern still present? 

    Yes  CHECK OASIS for any applicable service articles: TSB, GSB, SSM or FSA. If a service article exists for this concern, DISCONTINUE this test and FOLLOW the service article instructions. If no service articles address this concern, INSTALL a new RGTM. REFER to: Rear Gate Trunk Module (RGTM) .
    No  The system is operating correctly at this time. The concern may have been caused by module connections. ADDRESS the root cause of any connector or pin issues.

  8. M7 CHECK FOR CORRECT BCM (BODY CONTROL MODULE) OPERATION

    • Disconnect and inspect all BCM connectors.

    • Repair:

      • corrosion (install new connector or terminals - clean module pins)
      • damaged or bent pins - install new terminals/pins
      • pushed-out pins - install new pins as necessary

    • Reconnect the BCM connectors. Make sure they seat and latch correctly.

    • Operate the system and determine if the concern is still present.

    Is the concern still present? 

    Yes  CHECK OASIS for any applicable service articles: TSB, GSB, SSM or FSA. If a service article exists for this concern, DISCONTINUE this test and FOLLOW the service article instructions. If no service articles address this concern, INSTALL a new BCM. REFER to: Body Control Module (BCM)  .
    No  The system is operating correctly at this time. The concern may have been caused by module connections. ADDRESS the root cause of any connector or pin issues.
scientia non olet · About LEMON Manuals