Installation Procedure

Courtesy of GENERAL MOTORS COMPANY

NOTE:
Some components not shown for graphic clarity.

Drive Motor Power Inverter Module Cover Gasket (2) @ Drive Motor Power Inverter Module - Install
Drive Motor Power Inverter Module (1) - Install
Courtesy of GENERAL MOTORS COMPANY

CAUTION:
Refer to Fastener Caution .

NOTE:
Some components not shown for graphic clarity.

Drive Motor Power Inverter Module Bolt (1) - Install and tighten in sequence [16x] - Fastener Specifications
Courtesy of GENERAL MOTORS COMPANY

NOTE:
Some components not shown for graphic clarity.

Drive Motor Power Inverter Module Connector Bolt (1) - Install and tighten [3x] - Fastener Specifications
Courtesy of GENERAL MOTORS COMPANY

NOTE:
Some components not shown for graphic clarity.

Drive Motor Power Inverter Module Cover Gasket (3) @ Drive Motor Power Inverter Module Cover - Install
Drive Motor Power Inverter Module Cover (2) - Install
Drive Motor Power Inverter Module Cover Bolt (1) - Install and tighten [4x] - Fastener Specifications
Courtesy of GENERAL MOTORS COMPANY

NOTE:
Some components not shown for graphic clarity.

Install the battery positive and negative cable (5).
Connect the electrical connector. (4)
Install the battery positive and negative cable retainer (3).
Battery Cable Clip Bracket Bolt (2) - Install and tighten [4x] - Fastener Specifications
Connect the electrical connector. (1)
Courtesy of GENERAL MOTORS COMPANY

NOTE:
Some components not shown for graphic clarity.

Install the engine wiring harness.
Install the engine wiring harness retainers.
Connect the electrical connector. (1)
Courtesy of GENERAL MOTORS COMPANY

NOTE:
Some components not shown for graphic clarity.

Front Electric Drive Transmission Module Cooler Coolant Hose (1) - Connect
Courtesy of GENERAL MOTORS COMPANY

NOTE:
Some components not shown for graphic clarity.

Install the high voltage battery heater bracket (3) and the attached cooling hoses.
Install the engine wiring harness retainer (2).
High Voltage Battery Heater Bracket Bolt (1) - Install and tighten [2x] - Fastener Specifications
Courtesy of GENERAL MOTORS COMPANY

NOTE:
Some components not shown for graphic clarity.

Air Conditioning Refrigerant Heat Exchanger (2) - Install
Air Conditioning Evaporator Bracket Bolt (1) - Install and tighten [2x] - Fastener Specifications
Courtesy of GENERAL MOTORS COMPANY

NOTE:
Some components not shown for graphic clarity.

Install the high voltage battery coolant cooler outlet hose retainer (3).
High Voltage Battery Coolant Cooler Outlet Hose (2) - Connect
Connect the electrical connector. (1)
Courtesy of GENERAL MOTORS COMPANY

NOTE:
Some components not shown for graphic clarity.

Install the front electric drive transmission module hose retainer (2).
Front Electric Drive Transmission Module Hose (1) - Connect [2x]
Courtesy of GENERAL MOTORS COMPANY

NOTE:
Some components not shown for graphic clarity.

Install the high voltage battery coolant pump inlet hose retainer (3).
High Voltage Battery Coolant Pump Inlet Hose (2) - Connect
Connect the electrical connector. (1)
Courtesy of GENERAL MOTORS COMPANY

NOTE:
Some components not shown for graphic clarity.

High Voltage Battery Coolant Inlet Hose (2) - Connect
Connect the electrical connector. (1)
Courtesy of GENERAL MOTORS COMPANY

High Voltage Battery Heater Module (3) - Install
High Voltage Battery Heater Bracket Bolt (2) - Install and tighten [4x] - Fastener Specifications
Connect the electrical connectors. (1)
Courtesy of GENERAL MOTORS COMPANY

Front Suspension Strut Housing Brace (1) - Install
Courtesy of GENERAL MOTORS COMPANY

Front End Sheet Metal Cross Brace Bolt (1) - Install and tighten [12x] - Fastener Specifications
Install any wiring harness retainers as necessary.
Enable the high voltage system. High Voltage Enabling
Fill the drive motor battery cooling system. Drive Motor Battery Cooling System Draining and Filling
Run all necessary programming and setup procedures. Control Module References