Common Specs & Procedures Index
COMMON SPECS & PROCEDURES
| SYSTEM | SPECIFICATION/PROCEDURE | ||
|---|---|---|---|
| Air Conditioning | |||
| Torque | General HVAC Service refer to: FASTENER SPECIFICATIONS | ||
| Wheel Drive Shaft Nut | |||
| Front/Rear | First Pass: 330 N.m (244 lb ft) Second Pass: Loosen 45 Degrees Final Pass: 270 N.m (199 lb ft) |
||
| Battery | BATTERY INSPECTION / TEST , or BATTERY ELECTRICAL DRAIN / PARASITIC LOAD TEST | ||
| Brakes | |||
| Bleeding Sequence | RIGHT REAR, LEFT REAR, RIGHT FRONT, LEFT FRONT HYDRAULIC BRAKE SYSTEM BLEEDING (MANUAL) , or HYDRAULIC BRAKE SYSTEM BLEEDING (PRESSURE) |
||
| Disc Brakes | |||
| Service Specifications | DISC BRAKE COMPONENT SPECIFICATIONS | ||
| Torque | Disc Brake Servicing FASTENER SPECIFICATIONS | ||
| Charging | |||
| Generator | CHARGING SYSTEM TEST | ||
| Torque | FASTENER SPECIFICATIONS | ||
| Drive Belts | |||
| Adjustment | Non-Adjustable Serpentine Belt | ||
| Drive Belt Routing | |||
| 2.5L | See appropriate figure under ACCESSORY DRIVE PRIMARY BELT REPLACEMENT | ||
| Engine Cooling | |||
| General Service Specifications | SPECIFICATIONS | ||
| Radiator Cap Pressure | PRESSURE CAP TESTING | ||
| Engine Coolant Flow Control Valve R & I | |||
| 2.5L | ENGINE COOLANT FLOW CONTROL VALVE REPLACEMENT | ||
| Water Pump R & I | |||
| 2.5L | WATER PUMP MODULE REPLACEMENT | ||
| Engine Mechanical | |||
| 2.5L | |||
| Compression | ENGINE COMPRESSION TEST | ||
| Oil Pressure | @ 1500 RPM 100°C - 33.36 - 24.66 Psi | ||
| Overhaul | ENGINE MECHANICAL SPECIFICATIONS | ||
| Torque | FASTENER SPECIFICATIONS | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE/FLUIDS tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flex Plate (2.5L A/T) Torque | First Pass: 15 N.m (11 lb ft) Final Pass: 75 degrees | ||
| Fuel System | |||
| Pressure Specification | |||
| 2.5L | Ignition ON, engine OFF, command the Fuel Pump Enable On. Verify that the scan tool Fuel Pressure Sensor parameter is between 320 to 696 kPa (46 to 101 PSI). After the fuel pump stops operating, verify that the scan tool Fuel Pressure Sensor parameter is between 468 and 614 kPa (68 and 89 PSI). |
||
| Fuel Pressure Test Procedure | |||
| 2.5L | CIRCUIT / SYSTEM VERIFICATION | ||
| Fuel Filter Location | Fuel Filter is Part of the Fuel Tank Fuel Pump Module | ||
| Fuel Filter R & I | |||
| 2.5L | FUEL TANK FUEL PUMP MODULE REPLACEMENT (FWD) , or FUEL TANK FUEL PUMP MODULE REPLACEMENT (F48) | ||
| Ignition | |||
| Firing Order & Cylinder Identification | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires (Resistance) | Individual Ignition Coil/Module Assemblies | ||
| Ignition Wires (Routing) | Coil On Plug | ||
| Spark Plugs | |||
| Spark Plug - For application, see parts catalog. | |||
| 2.5L | |||
| Gap | 0.65 - 0.75 mm (0.025 - 0.029 in) | ||
| Torque | 16 N.m (12 lb ft) | ||
| Starting | |||
| Starter | |||
| 2.5L | STARTER REPLACEMENT | ||
| Torque | FASTENER SPECIFICATIONS | ||
| Wheel Alignment | |||
| Adjustment Specifications | WHEEL ALIGNMENT SPECIFICATIONS | ||
| Torque | FASTENER SPECIFICATIONS | ||
| Wheel & Tire | |||
| Wheel Nut Torque | 190 N.m (140 lb ft) For Wheel Nut Tightening Sequence, see appropriate figure under INSTALLATION PROCEDURE |
||