(Front Axle Assembly Removal And Installation)
Abbreviated Procedures
| Work | H/W | Tightening torque N.m (kgf.m/lb-ft) | SST/Equipment | Chemical | etc | |
|---|---|---|---|---|---|---|
|
||||||
| 1 | Disconnect the 12V battery negative (-) terminal | - | - | - | - | - |
| 2 | Remove the front wheel and tire | Bolt | 137.3 - 156.9 (14.0 - 16.0/101.3 - 115.7) | - | - | Remove the wheel and tire using the centering pin |
| 3 | Disconnect the front brake hose | Bolt | 24.5 - 29.4 (2.5 - 3.0/18.1 - 21.7) | - | - | Do not reuse washer |
| 4 | Remove the front brake caliper | Bolt | 98.1 - 117.7 (10.0 - 12.0/72.3 - 86.8) | - | - | Do not reuse bolt |
| 5 | Remove the front brake disc | Screw | 4.9 - 5.8 (0.5 - 0.6/3.6 - 4.3) | - | - | - |
| 6 | Unlock the driveshaft lock hub nut caulking | - | - | - | - | Refer to Shop Information |
| 7 | Remove the caulking nut | Nut | 294.2 - 313.8 (30.0 - 32.0/217.0 - 231.5) | - | - | Refer to Shop Information |
| 8 | Remove the dust cover | Bolt | 6.9 - 10.8 (0.7 - 1.1/5.1 - 8.0) | - | - | - |
| 9 | Disconnect the front wheel speed sensor | Bolt | 8.8 - 13.7 (0.9 - 1.4/6.5 - 10.1) | - | - | - |
| 10 | Remove the brake hose bracket bolt | Bolt | 8.8 - 13.7 (0.9 - 1.4/6.5 - 10.1) | - | - | - |
| 11 | Remove the tie rod end split pin and nut | Nut | 98.1 - 117.7 (10.0 - 12.0/72.3 - 86.8) | - | - | - |
| 12 | Remove the tie rod end ball joint | - | - | 09568-2J100 | - | - |
| 13 | Remove the lateral arm bolt and nut from the sub frame | Bolt/Nut | 156.9 - 176.5 (16.0 - 18.0/115.7 - 130.2) | - | - | - |
| 14 | Remove the front under cover | Bolt | 7.8 - 9.8 (0.8 - 1.0/5.8 - 7.2) | - | - | - |
| 15 | Remove the side cover | Bolt | 8.8 - 13.7 (0.9 - 1.4/6.5 - 10.1) | - | - | - |
| 16 | Remove the tension arm bolt and nut from the sub frame | Bolt/Nut | 156.9 - 176.5 (16.0 - 18.0/115.7 - 130.2) | - | - | - |
| 17 | Separate the front drive shaft from the hub bearing | - | - | - | - | - |
| 18 | Remove the tension arm split pin and nut | Nut | 98.1 - 117.7 (10.0 - 12.0/72.3 - 86.8) | - | - | - |
| 19 | Remove the tension arm ball joint | - | - | 09568-2J100 | - | - |
| 20 | Remove the lateral arm split pin and nut | Nut | 98.1 - 117.7 (10.0 - 12.0/72.3 - 86.8) | - | - | - |
| 21 | Remove the lateral arm ball joint | - | - | 09568-2J100 | - | - |
| 22 | Remove the knuckle upper bolt and nut | Bolt/Nut | 107.9 - 127.5 | |||
| (11.0 - 13.0/79.6 - 94.0) | ||||||
| 23 | Remove the front knuckle from the front strut | - | - | 0K517-J5100 | - | Below than 8.0 mm |
| 24 | Remove the hub bearing from the knuckle | Bolt | 88.3 - 107.9 (9.0 - 11.0/65.1 - 79.6) | - | - | - |
|
||||||
| Install in the reverse order of removal | ||||||
|
||||||
|
||||||