LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Honda >> 2014 >> Fit >> Repair and Diagnosis >> External Pages >> Different car >> Section 27 (Cruise Control) >> Symptom Troubleshooting Index
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Symptom Troubleshooting Index

WARNING: This page is about a different car, the 2013 Honda Fit, 2012 Honda Fit, 2011 Honda Fit, 2010 Honda Fit, and 2009 Honda Fit. However, it is still accessible from the selected car via links, so may be relevant.
TROUBLESHOOTING TABLE

Symptom Diagnostic procedure Also check for
Cruise control cannot be set
  1. Check the No. 24 (10 A) fuse in the under-dash fuse/relay box.
  2. Do CRUISE CONTROL COMBINATION SWITCH TEST  .
  3. Do CRUISE CONTROL INPUT TEST  .
  4. Check for PGM-FI DTCs (see GENERAL TROUBLESHOOTING INFORMATION ).
  • Poor ground G101 (A/T model) or G401 (M/T model)
Cruise control can be set, but the cruise main indicator does not come on
  1. Do the gauge control module self-diagnostic function procedure (see SELF-DIAGNOSTIC FUNCTION ).
  2. Do CRUISE CONTROL INPUT TEST  . Test the cruise control main switch signal input.
  3. Check for PGM-FI DTCs (see GENERAL TROUBLESHOOTING INFORMATION ).
 Faulty gauge control module
Cruise control can be set, but the cruise control indicator does not come on
  1. Do the gauge control module self-diagnostic function procedure (see SELF-DIAGNOSTIC FUNCTION ).
  2. Do CRUISE CONTROL INPUT TEST  ). Test the cruise control indicator signal input.
  3. Check for PGM-FI DTCs (see GENERAL TROUBLESHOOTING INFORMATION ).
 Faulty gauge control module
Vehicle does not accelerate accordingly when the resume/accel button is pressed
  1. Do CRUISE CONTROL COMBINATION SWITCH TEST  .
  2. Do CRUISE CONTROL INPUT TEST  . Test the cruise control resume/accel switch signal input.
  3. Check for PGM-FI DTCs (see GENERAL TROUBLESHOOTING INFORMATION ).
 Open circuit, loose or disconnected terminals: LT GRN/BLK, or BLU wire
Set speed does not cancel when the brake pedal is pressed
  1. Do the brake pedal position switch test (see HIGH MOUNT BRAKE LIGHT REPLACEMENT ).
  2. Do CRUISE CONTROL INPUT TEST  . Test the brake pedal position switch signal input.
  3. Check for PGM-FI DTCs (see GENERAL TROUBLESHOOTING INFORMATION ).
  • Short to power on the BRN wire
  • Faulty brake pedal position switch
Set speed does not cancel (engine rpm stays high) when the clutch pedal is pressed (M/T model)
  1. Do CLUTCH PEDAL POSITION SWITCH TEST  .
  2. Do CRUISE CONTROL INPUT TEST  . Test the clutch pedal position switch signal input.
  3. Check for PGM-FI DTCs (see GENERAL TROUBLESHOOTING INFORMATION ).
  • Short to ground on the PUR wire
  • Faulty clutch pedal position switch
Set speed does not cancel when the cruise control main button is pressed
  1. Do CRUISE CONTROL COMBINATION SWITCH TEST  .
  2. Do CRUISE CONTROL INPUT TEST  . Test the cruise control main switch signal input.
  3. Check for PGM-FI DTCs (see GENERAL TROUBLESHOOTING INFORMATION ).
 Short to power on the PNK, or LT GRN wire
Set speed does not cancel when the cancel button is pressed
  1. Do CRUISE CONTROL COMBINATION SWITCH TEST  .
  2. Do CRUISE CONTROL INPUT TEST  . Test the cruise control cancel switch signal input.
  3. Check for PGM-FI DTCs (see GENERAL TROUBLESHOOTING INFORMATION ).
 Open circuit, loose or disconnected terminals: YEL/RED, RED or LT GRN/BLK, BLU wire
Set speed does not resume when the resume/accel button is pressed (with the cruise control main switch turned on, and set speed temporarily canceled by pressing the brake pedal)
  1. Do CRUISE CONTROL COMBINATION SWITCH TEST  ).
  2. Do CRUISE CONTROL INPUT TEST  ). Test the cruise control resume/accel switch signal input.
  3. Check for PGM-FI DTCs (see GENERAL TROUBLESHOOTING INFORMATION ).
 Open circuit, loose or disconnected terminals: LT GRN/BLK, or BLU wire
Set speed does not resume when the resume/accel button is pressed (with the cruise control main switch turned on, and set speed temporarily canceled by pressing the clutch pedal) (M/T model)
  1. Do CRUISE CONTROL COMBINATION SWITCH TEST  .
  2. Do CRUISE CONTROL INPUT TEST  . Test the cruise control resume/accel switch signal input.
  3. Check for PGM-FI DTCs (see GENERAL TROUBLESHOOTING INFORMATION ).
 Open circuit, loose or disconnected terminals: LT GRN/BLK, or BLU wire
Light switch turned on, the cruise control combination switch illumination does not come on
  1. Check the No. 29 (10 A) fuse in the under-dash fuse/relay box
  2. Do CRUISE CONTROL COMBINATION SWITCH TEST  ). Test the cruise control resume/accel switch signal input..
 Open circuit, loose or disconnected terminals: GRY, RED/BLK, GRN, and RED wire
scientia non olet · About LEMON Manuals