LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Infiniti >> 2006 >> M35 Base >> Repair and Diagnosis >> Body & Frame >> Door Locks >> Body, Lock & Security System >> Intelligent Key System >> Check Park Position Switch
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Check Park Position Switch

  1. CHECK PARK POSITION SWITCH INPUT SIGNAL 

    With CONSULT-II 

    Check ("P RANGE SW") in "DATA MONITOR" mode.

    MONITOR ITEM CONDITION

    Monitor item Condition
    P RANGE SW A/T device P position: ON
    Other than above: OFF
    Fig 1: Display DATA MONITOR Mode
    G04145252Courtesy of NISSAN MOTOR CO., U.S.A.

    Without CONSULT-II 

    1. Turn ignition switch OFF.
    2. Check voltage between Intelligent Key unit connector and ground.
      VOLTAGE SPECIFICATIONS

      Terminals A/T device position Voltage (V) (Approx.)
      (+) (-)
      Intelligent Key unit connector Terminal
      M32 27 Ground P 0
      Other than above Battery voltage
    Fig 2: Checking Voltage Between Intelligent Key Unit Connector And Ground
    G04145253Courtesy of NISSAN MOTOR CO., U.S.A.

    OK or NG 

    OK: Park position switch circuit is OK.

    NG: GO TO 2.

  2. CHECK INTELLIGENT KEY UNIT OUTPUT SIGNAL 

    Check voltage between Intelligent Key unit connector and ground.

    VOLTAGE SPECIFICATIONS

    Terminals Condition Voltage (V) (Approx.)
    (+) (-)
    Intelligent Key unit connector Terminal
    M33 58 Ground Wake-up state (Open drive side door) Battery voltage
    Sleep state (After 30 seconds or more since all doors are closed under the condition that the ignition switch is in the LOCK position) 0
    Fig 3: Checking Voltage Between Intelligent Key Unit Connector And Ground
    G04145254Courtesy of NISSAN MOTOR CO., U.S.A.

    OK or NG 

    OK: GO TO 3.

    NG: Check the condition of harness and connector.

  3. CHECK PARK POSITION SWITCH 
    1. Disconnect A/T device connector.
    2. Check A/T device.
      CONTINUITY CONDITIONS

      Terminal A/T device position Continuity
      A/T device
      9 10 P Yes
      Other than above No

    OK or NG 

    OK: GO TO 4.

    NG: Check A/T shift lock system. Refer to "A/T SHIFT LOCK SYSTEM ".

    Fig 4: Checking A/T Device
    G04145255Courtesy of NISSAN MOTOR CO., U.S.A.
  4. CHECK HARNESS CONTINUITY 1 
    1. Disconnect A/T device connector.
    2. Check continuity between Intelligent Key unit connector and A/T device connector.
      CONTINUITY CONDITIONS

      A B Continuity
      Intelligent Key unit connector Terminal A/T device connector Terminal
      M32 27 M133 10 Yes
    3. Check continuity between Intelligent Key unit connector and ground.
      CONTINUITY CONDITIONS

      A Ground Continuity
      Intelligent Key unit connector Terminal
      M32 27 No
    Fig 5: Checking Harness Continuity 1
    G04145256Courtesy of NISSAN MOTOR CO., U.S.A.

    OK or NG 

    OK: GO TO 5.

    NG: Repair or replace harness between Intelligent Key and A/T device.

  5. CHECK HARNESS CONTINUITY 2 
    1. Check continuity between Intelligent Key unit connector and A/T device connector.
      CONTINUITY CONDITIONS

      A B Continuity
      Intelligent Key unit connector Terminal A/T device connector Terminal
      M33 58 M133 9 Yes
    2. Check continuity between Intelligent Key unit connector and ground.
      CONTINUITY CONDITIONS

      A Ground Continuity
      Intelligent Key unit connector Terminal
      M33 58 No
    Fig 6: Checking Harness Continuity 2
    G04145257Courtesy of NISSAN MOTOR CO., U.S.A.

    OK or NG 

    OK: Check the condition of harness and connector.

    NG: Repair or replace harness between Intelligent Key and A/T device.

scientia non olet · About LEMON Manuals