LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Infiniti >> 2013 >> FX37 Base, AWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 3 (Engine Control System (Introduction)) >> System Description >> Diagnosis System (ECM) >> Diagnosis Description >> CONSULT Function >> Active Test Mode
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Active Test Mode

WARNING: This page is about a different car, the 2013 Infiniti FX50. However, it is still accessible from the selected car via links, so may be relevant.
TEST ITEM

TEST ITEM CONDITION JUDGMENT CHECK ITEM (REMEDY)
VENT CONTROL/V
  • Ignition switch: ON (Engine stopped)
  • Turn solenoid valve ON and OFF with the CONSULT and listen to operating sound.
 Solenoid valve makes an operating sound.
  • Harness and connectors
  • Solenoid valve
ENG COOLANT TEMP
  • Engine: Return to the original non-standard condition
  • Change the engine coolant temperature using CONSULT.
 If malfunctioning symptom disappears, see CHECK ITEM.
  • Harness and connectors
  • Engine coolant temperature sensor
  • Fuel injector
FUEL INJECTION
  • Engine: Return to the original non-standard condition
  • Change the amount of fuel injection using CONSULT.
 If malfunctioning symptom disappears, see CHECK ITEM.
  • Harness and connectors
  • Fuel injector
  • Air fuel ratio (A/F) sensor 1
FUEL/T TEMP SEN
  • Change the fuel tank temperature using CONSULT.
PURG VOL CONT/V
  • Engine: After warming up, run engine at 1, 500 rpm.
  • Change the EVAP canister purge volume control solenoid valve opening percent using CONSULT.
 Engine speed changes according to the opening percent.
  • Harness and connectors
  • Solenoid valve
FAN DUTY CONTROL(1)
  • Ignition switch: ON
  • Change duty ratio using CONSULT.
 Cooling fan speed changes.
  • Harness and connectors
  • Cooling fan motor
  • Cooling fan relay
  • Cooling fan control module
  • IPDM E/R
ALTERNATOR DUTY
  • Engine: Idle
  • Change duty ratio using CONSULT.
 Battery voltage changes.
  • Harness and connectors
  • IPDM E/R
  • Alternator
EXH V/T ASSIGN ANGLE
  • Engine: Return to the original non-standard condition
  • Change exhaust valve timing using CONSULT.
 If malfunctioning symptom disappears, see CHECK ITEM.
  • Harness and connectors
  • Exhaust valve timing control magnet retarder
POWER BALANCE
  • Engine: After warming up, idle the engine.
  • A/C switch OFF
  • Selector lever: P or N
  • Cut off each injector signal one at a time using CONSULT.
 Engine runs rough or stops.
  • Harness and connectors
  • Compression
  • Fuel injector
  • Power transistor
  • Spark plug
  • Ignition coil
INT V/T ASSIGN ANGLE
  • Engine: Return to the original non-standard condition
  • Change intake valve timing using CONSULT.
 If malfunctioning symptom disappears, see CHECK ITEM.
  • Harness and connectors
  • Intake valve timing control solenoid valve
IGNITION TIMING
  • Engine: Return to the original non-standard condition
  • Timing light: Set
  • Retard the ignition timing using CONSULT.
 If malfunctioning symptom disappears, see CHECK ITEM.
  • Perform Idle Air Volume Learning.
(1) Leaving cooling fan OFF with CONSULT while engine is running may cause the engine to overheat.
scientia non olet · About LEMON Manuals