Work Procedure

WARNING: This page is about a different car, the 2012 Infiniti M35h. However, it is still accessible from the selected car via links, so may be relevant.

CAUTION: Make sure to use CONSULT when performing stroke sensor 0 point learning. (It cannot be performed by any means other than CONSULT.)

VEHICLE CONDITION
1. Stop the vehicle.
2. Turn the ignition switch OFF.
  : GO TO 2.
CHECK 12V BATTERY
Check the 12V battery. Refer to "WORK FLOW ".

Is the inspection result normal?

YES: GO TO 3.

NO: Charge or replace the 12V battery. Refer to "HOW TO HANDLE 12V BATTERY ". GO TO 3.
CHECKING INSTALLATION CONDITIONS OF BRAKE COMPONENTS
Check the installation conditions of brake components.

Is the inspection result normal?

YES: GO TO 4.

NO: Repair or replace error-detected parts and GO TO 4.
CHECK BRAKE PEDAL
Check each brake pedal height. Refer to "INSPECTION AND ADJUSTMENT ".

Is the inspection result normal?

YES: GO TO 5.

NO: Adjust each brake pedal height. Refer to "INSPECTION AND ADJUSTMENT ". GO TO 5.
PERFORM THE SELF-DIAGNOSIS
◦ With CONSULT-III.
1. Turn the ignition switch OFF to ON.
  CAUTION: Never set the vehicle to READY/Never start the engine.
2. Repeat step 1 two times or more.
  CAUTION: Be sure to wait for 5 seconds or more after turning the ignition switch OFF.
3. Turn the ignition switch OFF.
4. Close all doors including the trunk lid, and wait outside of vehicle for 5 minutes or more.
5. Turn the ignition switch ON.
  CAUTION: Never set the vehicle to READY/Never start the engine.
6. Erase self-diagnosis result of "BRAKE".
  CAUTION: Turn the ignition switch OFF and wait 5 minutes or more after erase self-diagnosis result.
7. Depress brake pedal by 100 mm (3.94 in) or more, and hold the position for 5 seconds or more.
8. Release brake pedal.
9. Repeat steps 7 to 8 three times.
10. Perform "BRAKE" self-diagnosis.
  Is a malfunction detected?
  
  YES: Check the DTC. Refer to "DTC INDEX ". GO TO 6.
  
  NO: GO TO 6.
PERFORM PEDAL STROKE SENSOR 0 POINT LEARNING
◦ With CONSULT-III.
1. Turn the ignition switch OFF and wait for 10 seconds.
2. Turn the ignition switch ON.
  CAUTION: Never set the vehicle to READY/Never start the engine.
3. Select "BRAKE", "WORK SUPPORT" and "STROKE SENSOR 0 POINT LEARNING" according to this order.
  CAUTION: Never depress brake pedal.
4. Touch "START".
  Was either "COMPLETED" or "The operation is incomplete. Try again after confirming the operation condition." displayed?
  
  "COMPLETED": Touch the "END". GO TO 7.
  
  "The operation is incomplete. Try again after confirming the operation condition.": GO TO 2.
CHECK DATA MONITOR
◦ With CONSULT-III.

Select "BRAKE", "DATA MONITOR" and "STROKE SEN 1 OUTPUT VOLT" according to this order. Check that this signal is within the specified value.

STROKE SEN 1 OUTPUT VOLT: 0.8 - 1.7 V

Is the inspection result normal?

YES: GO TO 8.

NO: GO TO 1.
ERASE SELF-DIAGNOSIS MEMORY
◦ With CONSULT-III.
1. Turn the ignition switch OFF, and then turn it ON again.
  CAUTION: Be sure to perform the operation above.
2. Erase self-diagnosis result of "BRAKE".
  CAUTION: Turn the ignition switch OFF and wait 5 minutes or more after erase self-diagnosis result.
  
  Are the memories erased?
  
  YES: INSPECTION END
  
  NO: Check the items indicated by the self-diagnosis.